Garden swing broke

Mosquito net - for a comfortable stay

Sitting on the street in the evening reading a book or handicraft, without fear of becoming a prey for mosquitoes? Put a swing by the flower garden without worrying about the bees climbing around? Easy if you have a mosquito net. It will also slightly muffle the sun's rays in the midday heat, protect from dust raised by the wind, and even save you from fine drizzling rain.

There are several types of mesh:

on one zipper in the center (swinging open according to the curtain principle), on two zippers on the sides (where the front part folds up) and solid (which needs to be lifted to go inside);

Garden swing with mosquito net

• stretching onto the roof under the awning, falling onto the awning from above, sewn into the awning;
• white or colored.

Choice of fabric, attention to detail

Variety of upholstery fabrics for armchairs

When choosing a finishing material, first of all, you need to pay attention to how to pull the chair, as well as indicators of strength and durability

1. For the living room, leather or fabrics with a distinct pattern are great: tapestry or jacquard. Correctly selected material will show guests the good taste of the owners of the house and will retain a good appearance for a long time.

2. The most durable and easy-care fabrics are suitable for a children's room. Such properties are possessed by flock or chenille - they are easily cleaned from various contaminants.

3. If you have pets such as a dog or cat, flock is great. This material is resistant to scratches and holes from sharp claws.

4. If you smoke a lot in the room where the chair will stand, then the best choice will be a material that is resistant to absorbing odors - chenille.

Having chosen the appropriate upholstery material, pay attention to the presence of a special impregnation. It will extend the service life, make it easier to care for the fabric

Therefore, before buying, check with the seller about the presence of impregnation.

Damage and types of repair

Damage to a sofa or other upholstered furniture can be of different "severity". Depending on the existing injuries, a different set of work is required. Here's what could be with your furniture:

• Only the fabric fell into disrepair (the cats on the armrests, for example, broke), i.e. there are no dips in the soft part and no protruding parts. Then everything is more or less simple and you can do with replacing the upholstery fabric.

• In some places there are crushed places. This damage is caused by wear on the components that make up the soft part of the sofa. Depending on the degree of damage and the design of the sofa itself, it may be necessary to replace the padding polyester and other underlying layers. In more severe cases, repair of the spring blocks, if any, or foam rubber / silicone, if the sofa is spring is required. If the upholstery looks decent enough, it can be washed and reused.

• Failure at the bottom of the seat. Sometimes, due to high loads, the springs pierce the bottom of the frame. This happens most often if it is made of fiberboard. In this case, you will have to disassemble everything, remove the spring dock, replace the fiberboard (preferably with plywood).

• Damage to the frame. One of the most unpleasant things is cracks in the frame bars. The sofa will have to be completely disassembled, the broken bars will have to be replaced, then everything will have to be restored. This is a complete banner of the sofa. Basically, you are assembling a new one.

So stretching the sofa can involve different jobs. From a simple upholstery replacement to a complete renovation including part of the frame. The most troublesome part is the spring blocks. This is a long and painstaking work. If the "historical accuracy" of your furniture is not important to you, it is easier to replace a failed spring block with foam rubber or (better, but more expensive) furniture silicone.If everything is done correctly, the sofa will become even more comfortable: incorrectly tightened springs cause a lot of inconvenience.

Common damage

The folding mechanism cannot transform or does it tightly. In this case, it is required to inspect the metal structure, to determine what interferes with the normal functioning. Elements can rust, bend.

Such problems can be solved by replacing part of the structure without completely changing the mechanism. Other common breakdowns:

1. A squeezed seat. This is due to the pushing of the filler. It is necessary to replace the foam rubber in the sofa, the thickness of which must be at least 4 centimeters. What to do if the sofa is sold out is written in another material.
2. A squeak when pressing on the seat, an uneven surface indicate that the spring system has become unusable. It is necessary to inspect the spring block, make its full or partial replacement.

3. The design fell through in the middle. This happens when there are problems with the framework. It is a frame covered with sheet material, which carries the greatest load during sitting. This can cause the sheet to break over time.

   It is necessary to remove the damaged sheet, replace it with a new one. The broken wooden frame must be dismantled, identical parts installed. The metal frame cannot be repaired without special tools (a welding machine is required).

4. Shabby, torn, cracked upholstery. The upholstery material wears out over time, and it can also be subject to mechanical damage. You can save the sofa with a banner. The fabric can be selected in a different color, density.

Important
Assessing the cost of restoration of the sofa, it should be borne in mind that the amount of more than 50% of the price of a new piece of furniture is unprofitable for restoration.

Recommendations of the masters

Furniture restoration experts advise you to adhere to the following rules when repairing sofas at home:

• do not save on building materials and fasteners - cheap accessories quickly fail;
• when fixing the upholstery, leave the edges a little longer - the fabric during use may stretch a little, gradually crawling out from under the metal brackets;
• broken wooden elements must be completely replaced, and not reinforced;
• to sew parts of the pattern only with nylon thread - it is very strong.

We have prepared not only articles on the repair of sofas, but also information on where to put such furniture, how to make it from pallets and how to determine and change the corners of the corner variety.

With a little effort, you can independently restore a broken sofa that has lost its former appearance. The main thing is to use only high-quality materials for replacement.

Garden swing accessories: photo

Here we have garden swing broke
... We only served for a year. Apparently, the fabric is so unreliable, or maybe the excess weight affected them (seemingly infrequently). Perhaps you will be comforted by the fact that such cases are often discussed on the Internet :)

What to do if the fabric on the garden swing is torn?

The first
thought, of course - sew new
... The pattern there, of course, is primitive - an ordinary rectangle:

But for this, firstly, you need to find and buy a suitable durable fabric and thread. Secondly, having sewn the cover, it will be possible to put it on only by untwisting the entire structure of the swing.

Second
an option for handy men is to get rid of the rags and make a full swing out of the boards. It turns out cool! But also not our option.

So we went along the third
paths. I sew badly, I didn't want to bother. But you can replace the fabric of the swing ... with twine!

The cords in hardware stores are usually very thick and expensive. We figured that if a swing has a back and a seat 1 meter wide, it is wrapped in half ... twine needs 400 meters!

As a result, we bought in "Ashan" a polypropylene cord knitted with a core (made in Belarus), 3 mm, withstands 50-55 kgf - what you need :). A 20-meter skein cost 20 rubles.

In total, it took about 20 skeins:

The swing is ready for service again :)

A year has passed ... The swing is slowly rusting :(. I had to buy a thicker string and replace the front sticks with it.

Let's see how long our rocking chair will last.

In the warm season, they were outdoors, in the open air, exposed to rain and sun. Like most of the goods sold in Russian stores, the swing is made in China, respectively, they are inexpensive, although the quality is quite acceptable.

Although the swing is a garden swing, which implies that it will be used outdoors, the seat, which is made of fabric that looks quite sturdy, could not withstand the effects of rainwater and scorching sunlight.

One summer day, it burst under another lover of quiet rest.

After examining the place of the gap, it became clear that the fabric was simply worn out, so it makes no sense to sew it up. Repair or alteration required. You can replace the fabric with a more durable look, but the cost of the material and work will be higher than the price of the swing itself. Therefore, it was decided to make the seat out of pine gaps, of which there were plenty of them after the construction.

Support options

The stiffness of the support and its design affect the type of swing and its reliability. Each species has specific features and advantages. It is difficult to recommend a specific type by distinguishing it from the rest. First you need to study in detail all the options presented.

A-shaped

The support looks like the letter "A": two inclined posts, converging at the top, crossed by a horizontal tie. Manufactured from metal (box or pipe) to provide the required rigidity. But it is possible to use wood, while the cross-section of the elements increases proportionally. Complemented by an awning, this swing design becomes an ideal resting place.

U-shaped

A simpler option. Two vertical posts connected by a crossbar. Materials, as in the previous case, are metal or wood. The installation of the support requires observance of the corners, the accuracy of cutting the elements.

L-shaped

Seemingly primitive construction; if you use high-quality components, follow the installation technology, it can withstand a serious load. The support works according to the cantilever principle, therefore, the calculation of the bearing capacity is mandatory.

Pillows and decorative textiles for garden swings

Textile elements are the most vulnerable part of the swing. Rain, sun, accidentally spilled coffee, a dog jumping on the seat with dirty paws ... it is almost impossible to completely protect a swing standing on the street from dirt and external factors. As a result, the fabric of the pillows loses its neat appearance, fades out, irreducible stains appear, while the swing frame is still as good as new. However, replacing the pillows may not be a necessary measure, but a way to give the swing a more original look, to make the seat more comfortable and softer.

Making pillows with your own hands is not so difficult: standard seats usually consist of two components: a textile cover and a filler. But the choice of materials must be taken responsibly - this is the guarantee of their long service and your comfort. The requirements for textiles are as follows:

• resistance to fading in the sun;
• strength and durability;
• the fabric should be easy to wash, dry quickly, not shed or shrink when washing.

Pillows will make your stay more comfortable

Of course, synthetic materials are more practical, and especially leatherette - it seems that I wiped it with a cloth and the surface is like new. Only now it is very uncomfortable to sit on such pillows in the heat. The golden mean - blended fabrics made of cotton and synthetics or natural high strength, like tapestry.Another option is natural fabrics with a special treatment to increase their wear resistance (for example, with water and dirt-repellent impregnation).

Fillers for pillows can be:

• foam rubber;
• holofiber;
• synthetic winterizer;
• komer, expanded polystyrene (synthetic balls).

The seats of a multi-seat swing can consist of both several pillows and two rectangular mattresses, connected or not connected to each other. In addition to the actual seats, the swing is equipped with soft textile armrests, decorative pillows, "dooms" and capes. You can easily make them yourself.

To make the rest not only comfortable, but also aesthetically pleasing, surround the swing with flower beds or tubs with plants, install a decorative fountain next to it. If you have small children, build a sandpit or a playhouse nearby so you can stay in sight of the little ones.

If you wish, you can turn even the most unpretentious budgetary or home-made model of a garden swing into a luxurious place to relax, you just have to show your imagination and a certain amount of skill.

Recommended types

There are three types of fabrics that are recommended to be chosen when arranging a garden swing.

Acrylic fibers

High quality products are often made from acrylic fibers. Their main advantage is considered to be resistance to ultraviolet radiation and high strength. The listed properties are due to the fact that the fibers are completely treated with a special waterproof impregnation. Products made from acrylic fibers will last about ten years.

Polypropylene

Polypropylene is a high-quality and multifunctional fabric that is often used in agriculture and industry. Experts recommend using a laminated type of polypropylene fabric, as it has a number of advantages. The main advantages are:

• durability;
• high strength;
• dust protection;
• resistance to ultraviolet radiation.

Polyester

The most common type of synthetic fabric is polyester. Most often it is used in the manufacture of clothing, underwear or bedding. However, sometimes it is used when creating elements of a garden swing. Polyester is moisture, low temperature and UV resistant.

The advantages of do-it-yourself chair upholstery

Do-it-yourself new life for an old but beloved armchair

Making something with your own hands is a fascinating process that allows you to reveal your creativity. It is not for nothing that in the age of factory production, hand-made products are valued higher than factory counterparts.

Such a thing will surely attract the attention of guests, will decorate your interior.

An old armchair with ripped upholstery can be turned into a chic exclusive piece of furniture

Having decided to make a constriction of the old chair with your own hands, you are free in the choice of finishing materials, and you can also save on buying a new chair. Any design, texture, the only limitation is your imagination and imagination. And also hand-made things are much nicer and closer than those bought in a store.

Garden swing accessories: photo

A garden swing is one of the most enjoyable outdoor activities outside the city or in the yard of your house. The most important elements of the swing structure is its fabric covering, which is subject to the detrimental influence of natural factors and human actions in the process of use.

The choice of fabric for a garden swing, its color, structure depends on the taste of the buyer, below we will consider the main types of fabrics for a swing.

Garden swing standard design:

• The frame to which the bench is attached
• Visor in the form of a roof, fabric or metal.
• Fabric upholstery of a bench using foam rubber
• Cushions
• Armrests upholstered with fabric or made in the form of roller-like cushions.

What to look for when choosing fabrics for a swing:

1. The color of the fabric, the coloring should emphasize the individual feature of the swing, be not a brand, since the location is the street and eating on the swing is an integral element of a country holiday.
2. Fabric structure. Depending on which part the fabric will be used in:

For roof visor. This element is constantly exposed to direct sunlight and is exposed to wind and dust. It is recommended to use an awning fabric containing specially impregnated polyester for greater resistance to temperature heating, fading, penetration of dust and dirt between the fibers. Foreign companies use fabric for sewing tents with a density of at least 180 g / m 2

To protect against insects, a special fabric is widely used, in the form of a mesh, which allows completely blocking insects' access to a resting person.

Fabric upholstery for the swing bench, cushions and armrests. In addition to resistance to natural factors, it is necessary to take into account direct contact with the human body and it is desirable that a natural component (viscose, cotton, gabardine) be present in the fabric.

The device of the sofa on the springs "snake" and options for its restoration

"Snake" springs in expensive models are used as an additional means to increase elasticity. In budget models, a foam block can fit on this basis. They are attached to a wooden or metal frame across the seat - each spring separately. The installation step depends on the planned load. If your sofa begins to sag, or the springs have lost their elasticity, or are broken, it is treated with a replacement.

To increase elasticity and extend the life of the sofa, the number of "snakes" can be increased when the sofa is stretched. Another option is transverse reinforcement with rigid corsage ribbons (which are used for straps on bags, backpacks).

For durability and greater elasticity, use a corsage tape

The tape is nailed from one side to the frame. Professional furniture makers then tighten it with a special tool, but you can replace it with a regular bar wrapped around in the middle with coarse-grain sandpaper. Wrap a couple of turns of the tape on this bar, pull with both hands (make sure that the frame does not bend), fix the tape with staples or nails, release and cut off the excess. The same method is also suitable for extending the service life of a lamellar mattress.

Criteria for the selection of fabric for the awning

To choose the right fabric, you must familiarize yourself with the main selection criteria in advance.

Resistant to pollution

The material from which the awning is made should not get dirty quickly. Therefore, it is recommended to look for fabrics that are resistant to dirt. Awnings made of acrylic fibers are least likely to get dirty. Their surface is treated with special agents that prevent the appearance of dirt. Also, such fabrics repel dust particles and therefore rarely become covered with dust.

Micropores

Another criterion to consider when choosing a fabric is micropores. They are needed in order to better allow air to pass through. Too dense fabric materials do not allow it to pass through. Therefore, experts do not advise using them for the manufacture of an awning.

UV protection

Use fabrics with UV protection. Ultraviolet light is absorbed best of all by dark fabric, so you should not buy light-colored fabrics. Also, the level of absorption of ultraviolet radiation depends on the type of material itself. The most reliable is considered to be green cotton, which is dyed with natural dyes. Also, UV light can be absorbed by polyester.

Impregnation

There are several impregnations that are often used in the manufacture of fabric materials:

• in this case, the outer surface of the fabric is treated to protect it from moisture. The processed fibers do not get wet and are protected from water.
• polyurethane. This impregnation is applied to the inside of the product. Like the previous one, it is used to prevent getting wet.
• PD. This type of impregnation is used to protect the fibers from moisture and make them more durable.

Easy cleaning and washing

For the awning, it is necessary to choose fabrics that can be easily removed from the dirt accumulated on the surface. Clothes made of linen or polypropylene are well washed. To wash them, it is not necessary to use hot water, since the material is cleaned of impurities in warm water heated to forty degrees. Also, polyester tarpaulins can be easily cleaned from dirt.

Long service life

Every person wants the awning to serve for a long time and not deteriorate too quickly. Therefore, it is necessary to choose durable fabrics that cannot tear quickly. To independently determine the strength, you need to feel the material. It should be harsh and firm to the touch. If the fabric is soft and stretchy, then it will tear quickly.

Required set of tools

Necessary tools and materials for sewing the cover

Consider a set of tools that are required to tighten the chair. Prepare them in advance so as not to waste extra time.

The furniture stapler is the main working tool with which the upholstery is attached to the frame. You can buy it at any hardware or hardware store, at a low price. You need to buy special staples of the appropriate size for the stapler. It is better to take them with a margin so that you do not have to interrupt the work process.

Foam rubber or batting - if the old filler has lost its former elasticity, it is necessary to replace it with a new one. Sold at a hardware store or hardware store.

Furniture filler - foam rubber

Batting for filling upholstered furniture

Flat screwdriver or pry bar for removing old brackets.

The minimum set of tools for repairing furniture at home

A hammer, pliers, tailor's scissors, an adjustable wrench - all this is needed to fully assemble and disassemble the chair.

A sewing machine, tailor's chalk or a bar of soap to sew new upholstery.

A sewing machine is needed to sew a new chair cover

A metal brush, coarse and fine sandpaper - for renewing external wooden elements, as well as varnish or paint of the required shade.

Saving a garden swing from bad weather: protective cover

To protect the swing and especially its textile elements from the weather, be sure to purchase a cover made of waterproof material. There are two types of models on sale:

• covering exclusively the seat,
• closing the swing completely, together with the awning.

The second option is more practical, especially if the swing is in an open place, and not under a roof, if you are unable to clean it in case of rain or if you visit the dacha on short visits.

The cover will protect the swing from moisture, dust, bird "marks", traces of your own or neighboring animals walking around the site. On hot days, a cover draped over a swing with an open front will create a pleasant shade.

Advice. It is most practical to have several removable seat covers so that you can change them as needed.

GARDEN SWING SEAT REPAIR

The width of the seat is not large, so for its repair we needed only three boards 15 cm wide. The thickness must be chosen so that they would not break not only under the children, but also under their parents, burdened by immense consumption and beer. Tes with a thickness of 3 cm is quite suitable for these purposes.

The first step is to measure the metal frame under the seat and transfer the dimensions to the boards, cutting them off with a jigsaw.
We will process the gaps with an electric plane on all sides so that there are no burrs, roughness and irregularities.

Since the frame in front has rounded edges, we will do the same on one board with a jigsaw, cutting off the corners to the desired radius.

Next, we will remove the chamfers from all the gaps with a milling machine. Thus, we will move away from rectangular shapes and make our seat more interesting.

After that, we will bring them to a smooth state with a grinder. First, use a coarse-grain sandpaper, for example, 120, and finally sand it with a 320-grain wheel. Run your hand over the surface - it should be perfect.

Let's paint the gaps with varnish, which will accentuate the texture of the wood.

It remains to install the boards on the swing. We will need 4 furniture bolts with smooth heads for each. in the gorge and in the frame, insert the bolts and tighten them with nuts.

The repair of the garden swing seat has been completed.

After him, they became more reliable and durable. They are not afraid of rain or sun, and if you put the soft pillows that come with the swing on the boards, it will be imperceptible that the seat has been repaired. If you liked the article, share it on social networks.

A garden swing is a favorite attribute of a summer cottage pastime for children and adults. The modern market offers a wide range of garden swings: single and family, on chains and stationary metal profiles, sitting and folding into a full bed. However, the classic standard swing for 2-3 seats is undoubtedly popular. Every person gets used to household items, and when a favorite resting place fails, the burning question arises of replacing a garden swing. But what if you apply a little imagination, make an effort and fix the swing, giving them not only a second life, but also giving them such qualities as reliability, strength and durability? The two most popular ways to restore a garden swing will be discussed in the article below.

Materials used

The design, the type of swing, their design and the laboriousness required to bring the idea to its logical conclusion depend on the choice of material. Among the most popular are wood (preferably dried, without defects), rolled metal, chipboard (moisture resistant), plywood, and plastic.

Metal

Widespread, running material, widely used in everyday life and industry. Steel structures are lightweight, durable, and inexpensive. Pipes and a box profile are suitable for a swing. One problem is that such a kit needs to be assembled by welding or bolting, which requires tools, equipment, and installation skills.

Wood

The second most important and accessible material. If there is a sawmill nearby or you live in a forest, there will be no problems with raw materials for the swing at all. Before use, the wood is dried, rejected, impregnated with a composition to prevent rotting and the appearance of fungus, pests.

Plastic

In today's reality, plastic is used everywhere. It can also be used in the design of a swing, but not in supporting structures. A solid facing, a seat, a railing, a backrest will be made of plastic. A big plus of plastic is that it does not rot and does not oxidize, does not require protection.

The classic spring block sofa pie and possible problems

To understand how to repair a sofa at home, you need to know which layers of materials and in what sequence are needed. For example, in a sofa seat with a spring block, the sequence will be as follows (from bottom to top):

1. Plywood or timber frame. Plywood framing is more reliable, but longer and more difficult to make. Therefore, pine blocks are usually used. They are connected according to the thorn-groove principle, gluing the joint with wood glue. If desired, the connections can be reinforced with dowels or corners (aluminum).

2. Base for the spring block.There may be options: lamellas (strips of elastic material), fiberboard, plywood. The most budgetary option is fiberboard, the most expensive is lamellas. The lamellas are mounted on special stops (lat holders). When using plastic stops, there is a possibility of breakage. At the same time, low-quality lamellas can bend (in a normal state they are bent slightly upward) or break - to reduce the cost, they are often placed across a large gap. All this leads to the fact that the seat of the sofa is pressed through. Instead of wooden slats, there can still be snake springs. They also have sufficient elasticity but cost less. The problems with them are the same.
3. The spring block itself. The block can be with independent or dependent springs. The former is cheaper, the latter supports the body well. Such mattresses are also called orthopedic.

4. Felt or thick fabric (teak, other similar thick fabric will do). This layer is needed so that the springs do not push the foam rubber located above.

5. Polyurethane foam (polyurethane foam, foam rubber - all the names of one material). Special dense foam rubber is used. If you choose, in addition to density, look at such an indicator as the durability coefficient - the higher the number, the better (and more expensive). This indicator reflects how long the foam rubber will restore its original shape after removing the load. Its thickness is taken from the original, factory cake. You can make it thicker without restrictions only on upholstered furniture that cannot be expanded (bench, sofa, armchair).
6. Sintepon. It is necessary so that the fabric does not "wash" the PU foam. It is usually glued to a layer of foam rubber so that it does not fold into folds during operation. The glue is taken in a spray can.
7. Upholstery fabric. The best are tapestry, chenille. They do not crumble, it is easy to sew from them. Flock and jacquard are not bad fabrics, but some of them "creep" at the seams. Therefore, when sewing, the seams must be strengthened. By the way, it is better to sew the upholstery for the sofa with special Tytan threads. Regular ones, even thick ones, will tear quickly.

These are all layers and their features. You can add something (for example, a double layer of padding polyester), remove it is highly undesirable.

We disassemble the sofa and evaluate the scale of the work

The stretching of the sofa begins with its disassembly. In the process, you will be able to assess the extent of the damage and decide what exactly you need to do. For this part of the job, you will need:

• a large screwdriver to unscrew the visible bolts (if any);
• a small flathead screwdriver, pliers, or a staple remover - to remove the staples that secure the upholstery.

The main thing is to remove the old upholstery. Then everything will become clear

Actually, that's all. First, we remove individual pillows, if any, remove the sidewalls. It is difficult to tell here - there are many designs. Look carefully to see if you find something. If you have sliding parts, you can try to start with them.

Separating the upholstery

The next step is to separate the fabric from the frame. It is attached with staples to the timber frame bars. Hook the staples with a flat screwdriver, take out. Some can sit very tightly, it is easier to pull them out by grasping the raised back with pliers or pliers.

We disassemble the sofa: remove the staples

We remove the fabric carefully, trying not to damage it too much. We will then use it as a sample for the new upholstery of the sofa. There are several layers under the upholstery fabric. Maybe felt, synthetic winterizer, some kind of fabric. If the repair of the sofa was started only for the sake of replacing the upholstery, look at the condition of these materials. If there are signs of wear, it is best to replace it. After all, it will be a shame if, after a few months, the sofa's constriction is required again, but already due to the fact that the layers of the lining have been demolished.

If the sofa is old, there may be such a picture.

Once the fabric is removed, it's time to evaluate which parts you will need to change. Everything is clear with the upholstery and lining. It is advisable to keep the pie in the same composition.If old materials were used that are not on sale now or they are too expensive, replace them with modern counterparts. The main thing for folding sofas is to reach the same height of the seat and backrest, which were before, since the folding mechanisms are designed for certain parameters of the "pillows". In order not to be mistaken with the thickness of the materials, find the unworn (or least worn) areas and measure the thickness.

We estimate damage

This stage is necessary if the seat of the sofa is uneven, there are humps and depressions, protruding springs (and from below too). In seats that consist only of foam rubber, everything is simple: they usually go for replacement. They can be made of high-density foam rubber by folding several layers, you can order ready-made foam rubber in a store that sells furniture spare parts. It is reasonable to order a latex mattress according to the exact measurements (measured after the fabric and all layers have been removed).

If there are springs in the sofa, removing all the covering layers, we get to them. If there are no burst springs, the frame and its connections are strong, without backlash and cracks, the substrate for the springs is in a normal state, you can stop at this. We change the covering layers, sew a new cover, stretch and fasten. This completes the stretching of the sofa.

If there is any damage from the above, the spring block will have to be separated. It is attached to the frame frame using U-brackets or nails. Now you have completely disassembled your sofa into its components. Next is the replacement and repair of damaged parts, and then reassembly.