Ariston washing machine error codes

How is the electronic module checked?

This part of the Ariston washing machine is very difficult to repair. To begin with, you should have the necessary tools, and the skills of such work will not be superfluous at all. In addition, you will need spare parts that will have to be re-soldered if necessary.

To begin with, the board is called to identify the failed sections. It is best to entrust this work to an experienced specialist. By the way, the module is located at the bottom left, near the back of the Ariston.

There are cases in which the board was not repaired, but simply broken. This happened from ignorance of the features of the repair. Even replacing the entire part is nuanced. And the meaning of the repair does not at all consist in removing the failed Ariston washing machine board and installing a new one. The bottom line is that it must be programmed - "stitched", as experts say.

Testing faults

We will be able to check all the functions of the Ariston, find the fault and even understand how to fix the F06 error. This requires:

• take the SAT diagnostic key with coding 95 669;
• connect it to the connector on the back of the machine;
• if the Ariston unit has a drying mode, the key will light up with a green light. There are models on which the blue indicator lights up.

Remember that during testing, the temperature of the water will increase by thirty degrees. So before checking, you should set a certain mode. In addition, the Ariston washing machine is connected to the water supply, its tank must be empty, and the door is tightly closed.

To establish an F06 error or other breakdown, turn on the Ariston washing machine, press the "Auto-Test" button and hold it. At the same time, the scoreboard is monitored. If the test has started, “Test” will light up on the screen. A machine without a screen will emit a characteristic signal in this case.

The moment of appearance of the code and its analogues

Error 3e rarely appears spontaneously. More often it "jumps out" at certain stages of the washing program, showing a certain pattern. Imagine a Samsung washing machine starts washing clothes. Water is collected, the drum gradually begins to spin and suddenly, a hang occurs, the machine stops the rotation of the drum and at the same minute the display shows error 3e. It happens in another way.

• You are starting a washing program on a Samsung automatic washing machine.
• The machine draws in water and launches the wash.
• Next, the washer drains out the dirty water, draws in clean water for rinsing and starts rinsing.
• This should be followed by a spinning step, but spinning does not occur. The machine, having slightly spun the drum, freezes, giving an error with code 3e.

If you are faced exactly with the above symptoms, but a different code is displayed on the display, remember that error 3e has analogues with a similar decoding. It may very well be that you will come across codes: 3C, 8E, EA, 3e1, 3e2, 3e3, 3e4, 3c1, 3c2, 3c3, 3c4, 8e1, 8c, 8c1. Quite a lot of analogs, it is easy to make mistakes, so be careful. The EA code is typical for washers that came out before 2008, but the codes 8E, 8e1, 8c, 8c1 are typical for washers younger than 2013.

Another question arises: how does error code 3e appear on Samsung washing machines that do not have a display? In the picture below you will see the answer to it. When such an error occurs, two 40C lamps light up on the display, followed by Bio 60C. But that's not all, the wash program indicators will flash quickly.

How does it stand for?

As always, let's start by literally deciphering error 3e. It means a problem with the tachometer or the engine. Such a lengthy description of the error can hardly suit us, so we will try to decipher it in more detail. First of all, we will decipher the twin errors that are found on some models of Samsung washing machines instead of code 3e.

1. The error with the EA code is deciphered in exactly the same way as 3e, just this code was used on older Samsung washing machines, however, we already talked about this above.
2. Codes 8e, 8c, 8c1 mean problems with the vibration sensor, which is installed on the most modern models of washing machines.

1. Error 8e1 indicates serious malfunctions in engine control, in fact, a complete loss of communication with a vibration or tachometer.
2. Well, errors of the 3C series may appear due to the loss of engine power of the Samsung washing machine.

Why does the code appear?

Conventionally, the problems that this error "symbolizes" can be divided into two categories. The first category includes malfunctions that do not entail breakdown of parts and assemblies of the Samsung washing machine, and the second category includes more serious breakdowns that give rise to the need to carry out serious repairs to the "home assistant". So let's start with simple troubleshooting.

At first glance, it may seem ridiculous, but such banal things as overloading the drum with laundry can lead to an error with code 3e or 3C. If you put too little laundry, a 3C error may appear. These codes can also symbolize drum jamming due to foreign objects falling between the tank and the drum if the engine does not have enough power to overcome the jam. Any of the above errors can pop up due to a short-term failure in the self-diagnosis system, and if so, you are very lucky - nothing needs to be fixed.

Let's move on to the second category of faults. Error 3e may result from the complete combustion of the tachometer and a complete break in communication with it. If there is a vibration sensor on a Samsung washing machine instead of a tachometer, similar troubles may arise with it. Not everything is going smoothly with the engine either. When an error 3C appears, one can judge the loss of engine power due to worn brushes or a broken winding.

The tachometer may give incorrect signals due to oxidation of the magnetic ring or the motor shaft. Also, dirt gets between the motor shaft and the tacho sensor ring, which causes the same problems. Weakening of the tachometer signal, or its periodic disappearance may be due to poor attachment of this sensor to the engine, all this can also generate an error with code 3e.

One of the rarest causes of error 3e and its analogs is a loose drive belt. Due to a similar problem, the engine cannot gain speed and spin the drum, which is sometimes perceived by the washing machine's self-diagnosis system as a problem with the motor, which is why it issues code 3e.

Fault codes for Electrolux and Zanussi units

In the event of abnormal situations, the display of the Electrolux and Zanussi washing machines appears with corresponding inscriptions in the form of certain codes. Both types of washing machines have a common element base and differ only in the types of panels with individual interfaces.

The error codes are displayed as specific combinations of LEDs arranged vertically. There are eight such indicators in total, of which the top four correspond to the first digit of the error code, and the four lower ones correspond to the second digit. There are panels with sixteen indicators that display not only the numerical, but also the alphabetic value of the code.

In other control modules, malfunctions are indicated by sequentially repeating flashing of 2 indicator lamps, which turn on and off for 0.4 seconds, and the interval between each series is 2.5 seconds. In some models, the light signaling is supplemented by sound.

After finding the error code, you need to decode it correctly. Each such code is interpreted as follows:

• E11 - exceeding the time limit for reaching the standard water level in the tank. Most often this happens due to the weak water pressure.
• E13 - the water level falls due to a leak.
• E21 - exceeding the time limit for water discharge. The filter may be clogged.
• E23 and E24 - errors in the drain pump control circuits.

There are other error codes associated with malfunctions of sensors, an open hatch and a broken system for blocking it, short circuits and malfunctions in the control of the electric motor. All of them are described in more detail in the instruction manual attached to each specific model.

Causes of occurrence

Different reasons can lead to error E9 or L9. Some malfunctions can be eliminated by hand, in other cases the help of experienced specialists will be required. First of all, you need to check the following:

the tightness of the connection of the drainage hose to the sewage system and the hose itself for breaks; in the case of draining water into the bathroom or toilet, see if the hose is ripped off, if water is flowing past;

the correct connection of the drain hose to the sewer pipe, if the level of the hose is violated, then the water will spontaneously pour out of the tank;
the tightness of the installation of the drain filter, in the event that you pulled it out the day before for cleaning;
pay attention to whether water is flowing from the powder tray, if the holes for filling water into the tray are clogged, then the water will not flow into the tank, it will flow out;
after external inspection, proceed to inspect the "insides" of the washer, check the pipe from the tank to the pump and from the powder receiver to the tank, maybe there is a need to replace the clamps that hold the pipes;
check the contacts of the electrical wires going to the water level sensor and to the Aqua stop.

If an E9 error appears in a Samsung washing machine or any other, you can try to restart the washing machine, so to speak, reset the program. There may have been some kind of glitch that caused the error to appear. You can reset everything by unplugging the machine from the outlet for a few minutes.

More serious reasons are caused by breakage and malfunction of the part, in this case, these are:

• Aquastop sensor;
• rubber cuff;
• hose and pipes;
• pressure switch;
• electrical wiring and electronic module.

Change sensors

First, we will describe the replacement of the Aquastop sensor, this part is also called a microswitch with a float. It is located, as we have already noted, in the tray of the washing machine. Therefore, to replace it, it is necessary to disconnect the equipment from communications, pull it out to a convenient place and put it on its side. Then we do this:

1. unscrew the pallet;
2. carefully remove the pallet from the car, do not shade it sharply, so as not to tear off the wires coming from the sensor;
3. disconnect the chips with wires;
4. detach the latches and take out the sensor;
5. we put a new one in place of the faulty part.

The water level sensor, which is called a pressure switch, is, on the contrary, located at the top of the washing machine. You can also replace it yourself, having spent 20 minutes on work. To do this, disconnect the machine from the network, close the water supply tap, and then follow the instructions:

• unscrewing the rear bolts, remove the upper case cover;
• in the upper corner of the machine find a part as in the photo below;
• disconnect the chip with wires;
• unclench the clamp and remove the air supply tube;
• an original new part is installed in place of the faulty pressure switch.

Replacing the cuff and pipes

Replacing the cuff in any brand of washing machine is more time consuming than replacing the sensors. After all, in order to remove and put on an elastic band, you need to disassemble the body of the machine. Some experts, having the skills, can replace the cuff on a Samsung washer by removing only the top cover, but those who do it for the first time may not get this "trick".

We described in detail how to disassemble the washer and replace the rubber band in the article How to change the cuff in the washing machine, so we decided not to repeat ourselves.

As for the branch pipe, most often the branch pipe connecting the pump and the tank breaks. This part is replaced through the bottom. It is either absent or easily removable. The branch pipe is held in place with clamps, which will also need to be replaced.

What to do with the electronic module

The electronic module is not only the most expensive part in a washing machine, but also requires special knowledge during installation and especially during repair. If the processor on the control board is not burnt out, it can be repaired. Otherwise, the board will need to be completely changed.

When replacing an electronic module, there is such a nuance as firmware; some boards do not have software installed. To install it, you must first find it, and then carry out the process correctly. It is for this reason that we recommend contacting specialists and not taking responsibility for yourself. Perhaps, having learned the cost of a part and repair, you might even think about buying a new machine, because everything will cost a lot.

Thus, there are many reasons for the appearance of the E9 error. Most of them require the skills of repairing and disassembling the washing machine. We hope our article will help you determine the trajectory of actions in this situation. Good luck!

Errors in water supply

When there are problems with the supply and flow of water from the water supply system, several values ​​are displayed.

E1

At any stage of washing, an E1 error may appear on the display panel, indicating a problem with water entering the drum. The problem arises at the stage of water collection before washing, during preparation for rinsing the laundry.

There are several unfavorable factors in the emergence of a problem situation:

• lack of water;
• access to water is blocked (they often forget about a blocked tee tap);
• clogged filters;
• malfunction of the control system;
• damaged contacts and wiring.

4C2

The code will pop up on the display of the washing machine if hot water is supplied (temperature is above 55 degrees)

It is important to remember that only cold tap water should go into the drum of the machine.

The inlet hose should only be connected to a cold water tap. Before turning on the equipment, you need to check what kind of water is being poured. If it's hot, then you need to wait until the cold one flows. In the event that this did not happen, be sure to use the help of a plumber.

4C

This code indicates a problem with the water supply system. In some situations, you will be able to cope on your own, in others, you cannot do without the help of a specialist and replacement of some parts:

• The cold water supply is turned off in the entire plumbing system.
• Damage to any part of the hose.
• Hot water supply.
• Clogged or damaged filter.
• Incorrect water supply to the machine.

4E2

If the temperature of the water entering the drum is higher than 55 degrees, then the error code 4E2 will be displayed. The problem is associated with a malfunction in the sensor or wires connected to the control module.

4E

When the technician does not register the flow of water, an error 4E is issued. There are many reasons for its appearance:

• lack of water in the water supply;
• the supply tap is closed;
• breakdown of the filling valve;
• leaks lead to flooding of internal systems with water;
• damage to electrical wires;
• the value jumps out in the event of a breakdown of the control module.

4E1

Most often, the problem code occurs when the water temperature exceeds 70 degrees during the drying process of the washed items.

If the device does not provide for water heating, then a supply system for both cold and hot water from the water supply is equipped. Each hose has its own inlet valve. If you mix up the inlets, an error will occur. Such car models are extremely rare, so the problem is not common.

Ways to eliminate detected breakdowns

If a breakdown of the washing machine is detected, an error code will appear on its interface. For example, f 05. Having studied the manufacturer's instructions, you can understand how to proceed.

If f 01 is found, check the probability of contact of the J9 connector of the controller. Water can get on it. It will be useful to carry out a check on the part of corrosive processes on the contacts of the drive motor connector. To fix the problem, the controller and the drive motor must be replaced.

We measure the control voltages on the J09 block with a tester

If the display shows the value of 02, then you need to check the rotor of the drive motor for blockage. This can be due to problems with the drum bearings. It is also worth analyzing the quality of the contact between the J9 connector of the controller and the drive motor, to determine whether the electrical resistance of the tachogenerator winding has a sufficient level. The rate of this indicator ranges from 115 to 170 ohms. It is necessary to inspect the wiring and tachogenerator. If the motor in the model is three-phase, then you will need:

• evaluate the external circuits of contacts 6.7 of the J9 connector for an open;
• replace the drive motor and electronic controller.

Problem f 03 is solved by checking contacts 11, 12, as well as the J8 connector of the electronic controller and the NTC temperature analyzer. It is also worth analyzing the electrical resistance level of the NTC signaling device. If these parts are out of order, they are replaced.

Error f 04: you need to fill the washing machine tank with water up to the “overflow” mark and evaluate whether the contacts of the JЗ connector of the electronic controller are connected securely, the water level indicator. The situation is solved by replacing the level switch, controller.

At f 05, it is worth examining the quality of the connection of the contacts of the connector J9 of the electric controller, the drain pump, because f05 speaks of problems in this area. For f 06 - is there a connector contact, inspect the wiring from the board to the control panel.

f 07: for the AVD and AVL models, you need to determine the quality of the contacts of the J3 connector of the electric controller, the level detector, the quality of the latter, the operability of the heating element.

Checking the operation of the heating element

F 08 indicates the need to check the water level switch. If it is faulty, f 08 can only be eliminated by replacing this part.

F 09 indicates the need to replace the controller.

At f 10, it will be necessary to evaluate the contacts of the connector 33 of the controller and the level switch. At f 11, they analyze how reliable the connection is from pins 8, 9 of the J9 connector of the controller and to the drain pump.

F 12 indicates the need to check the contacts of the J11 connector of the electronic controller. At f 13, it is worth inspecting the contact of the CAN connector of the controller, the indicator of the drying temperature mode, at f14 - the contact of the connection between the electrical controller and the drying heating element, at f 15 - the contact of the CN1 connector.

Inspection of the board for damage to elements

The F 16 requires the drum to be overloaded.

At f 17, the following points should be checked:

• mains voltage of contacts 3.4 of connector J4 of the electronic controller.
• whether the microswitch of the door lock is activated;
• whether the hatch door lock clicks securely.

F 18 speaks of the relevance of replacing the electrical controller.

Causes of breakdown, elimination procedure

You can try to fix the F06 error on your own. To do this, you should:

• restart the Ariston washing machine so that the error is removed at this moment. To do this, the machine must be disconnected from the electrical network for about twenty minutes. If the attempt was unsuccessful, we begin to check further;
• if the panel malfunctions, the buttons stop responding to pressing. In this case, the panel of the Ariston washer simply changes;
• if the control board breaks down, it is necessary to check the module and replace it if necessary;
• from the display system and the control unit of the Ariston apparatus, the wiring could be broken, or the contact terminals simply moved away. Check the connections, replace damaged wiring.

In order to determine the exact problem of the F06 error, it is recommended to perform a self-test. Self-diagnosis will allow you to deal with the causes of the keyboard malfunction, even in a situation when the F06 code is not displayed.

Other causes of malfunction and their elimination

There are failures that are completely removable at home. But here it all depends on the model of your washing machine. If you have CM Ariston Arcadia:

1. Error F06 occurred due to the fact that the door is not locked - perhaps a foreign object has got between it and the panel, or you simply did not "press" it when closing. To fix error F06, remove the object or press the door firmly until you hear a characteristic click, which will confirm the tightness of the junction.
2. No power supply - check the contacts from the door interlock to the module. Install the clipper correctly using the construction level.

For Ariston type Dialogue machines:

1. The buttons do not launch the desired mode (they are not pressed or are not beaten back) - it is recommended to make an effort, press the problem button several times, starting and disabling the program. Error F06 should disappear.
2. Broken wiring. To fix error F06, you will have to perform a wiring check and fix the problem.

Both brands of Ariston have a program crash. In this case, the unit will have to be disconnected from the network and started again.

If you have clearly done all the manipulations, but the machine refuses to work and gives an error F06, you will have to call an experienced specialist.

The main malfunctions of Ariston washing machines

Breakdown of the heating element.
Thanks to this part, the water is heated to make the washing process more efficient. If a failure occurs for this reason, the machine itself will determine this and issue the corresponding fault code (F03). This can be either a malfunction of the element itself, or the accompanying breakthroughs in the power circuit due to the fact that the terminals are burnt out. To eliminate the breakdown, you need to replace the burned out heating element or fix the terminals.

Bearing breakage.
This malfunction is typical for almost all models of machines of any manufacturer, including the ariston hotpoint model. You can see how this is done in the video or in this article:

Continuous use of the machine leads to the fact that the bearing shaft is worn out, moisture can get into it. As a result - deformation of the part and incorrect operation of the washing machine.

It is not difficult to notice this breakdown - the machine starts making a lot of noise during the spinning phase. The sound differs significantly from normal operation. This breakage can be easily repaired by replacing new bearings. But working with faulty bearings can lead to serious problems - a violation of the drum attachment, damage to the tank. Such violations entail a major overhaul of the equipment.

Regardless of vertical or horizontal loading, model range, and other indicators, it may happen that the machine refuses to drain or fill water. The reasons may be blockages, burned out pump winding.

Sometimes, in order to adjust the work, it is enough to clean the filters, if their further work is impossible, replace them. If everything is normal with the filters, but the water still does not drain, you need to replace the pump.

Malfunctions of the Ariston Hotpoint washing machine can manifest itself in a water leak. The problem most often lies in the water set or drain hoses, depending on at which stage of the wash the leak is noticed. To fix the problem, you need to inspect the hose attachments to the machine.

Most often, you need to tighten the fixing nut or change the rubber seal. Less commonly, manhole cuffs and nozzles can be the culprits. In this case, replace the problem part.

Noise when the machine is running with reference bearings
... In situations like this, check if the machine is level. If not, you need to align its placement, and to reduce the level of vibration, you can put a rubber mat. If this is done and the car is still noisy, the problem may be with the shock absorbers or the tank strap.

The machine does not heat up the water

Problems in the heating circuit are indicated by the constant "freezing" of the device during washing, the lack of heating of the water, or constant filling and draining. Then signals f4, f7 or f8 are displayed on the washing machine display.

Malfunctions with heating elements or pressostat, indicated by codes f4, f7

Such errors, indicating a malfunction of the heating element, appear in those modes where washing is carried out with hot water. This happens immediately at start or after filling the water. Those programs where water heating is not needed work as usual.

In addition to the standard way of solving the problem, there are several more effective techniques to cope with this problem. If the problem manifests itself immediately and there is not even a set of water, then the heater has broken. It burns out or, due to loose contacts, "punches" onto the case. To eliminate the problem, check all the connections of the heating element and measure its resistance.

Important!

If the liquid is drained immediately after dialing, then the pressure switch has broken. Then the controller receives information that the heater is not in the water. Because of this, the water is not heated.

To eliminate the malfunction, check the hose with a pressure switch. It sometimes clogs, kinks, or falls off. Inspection of the sensor contacts will not be superfluous. They may need to be replaced. If the f4 code appears, then you need to change the pressure switch itself.

Problems are sometimes more serious. Therefore, to be sure, they check all the parts from the controller to the heater and the sensor responsible for the liquid level. If necessary, replace the burnt-out parts.

F8 Heating Circuit Malfunction

F8 fault symbols appear when the heater circuit is not working properly. Usually the cause is a breakdown of the pressure switch. Failure occurs due to high humidity. Therefore, the board is carefully wiped and blown with a hairdryer.

It is also recommended to check the contacts, they may have come off or need cleaning. This happens especially often when the device is started for the first time after transportation. In other cases, you cannot solve the problem on your own.

Malfunctions indicated by f8 symbols:

1. If the program is interrupted immediately after the start or the water does not heat up, the heating element must be replaced.
2. If the device stops after starting or when going to rinsing, some of the board's microcircuits are out of order and need to be replaced. There is also a possibility that a flashing of the board will help.
3. "Hanging" of the machine in different modes indicates a malfunction of the wiring or contacts. Also, the reason may be a breakdown of the pressure switch.

Important!

If, during the check of all elements, the malfunction could not be identified, then the control module of the machine itself will have to be changed to a new one.

How is the F06 error indicated on the Ariston washing machine

As always, you have put in a batch of laundry, defined the program, and activated the process. But your Ariston machine does not start washing, it may not even take in water, displaying the signal F06 on the display screen.

It is worth noting that the F06 error can also be detected at the very end of the washing process, when the program is completed, but the drum door does not open. And in this case, wait for the corresponding signal on the screen.

Rarely enough, the F06 error can occur in the following cases:

• at the time of washing, rinsing or wringing out;
• may appear at any time of operation, then disappears, and the Ariston machine works normally.

If your Ariston machine does not have a display, then the F06 error code is manifested by certain indicator signals, and here it all depends on the model itself.

What information can error codes provide?

Modern models of Ariston washing machines are equipped with a self-diagnostic function that allows you to determine the presence of a malfunction and notify the user about it using the appropriate code.

Understanding the meaning of the existing codes, the owner will be able to independently identify the breakdown and, if possible, take measures to eliminate it, without spending money on the services of third-party diagnosticians and repairmen.

If there is no display, the code will be displayed by flashing LED indicators. For example, the light blinked 5 times at short intervals, then paused and repeated the blinking cycle.

In this case, the machine tries to notify the user about the presence of an error under code 05. If the machine is equipped with a display, the code will be displayed directly on it, which is more convenient.

Thus, knowledge of the error codes of Ariston washing machines will allow the owner to independently understand what happened to his equipment, without calling the master for this. The information obtained will make it possible to draw conclusions about the severity of the existing faults.

For example, a machine may try to convey to the user information about the lack of water or a loosely closed manhole cover - would it be advisable in such a situation to call the master, when, as a rule, everything can be corrected on its own?

Along with this, breakdowns can be very significant, and they cannot be eliminated without third-party qualified assistance. In this case, knowledge of the codes is also very useful.

Remember: self-repair of a washing machine is an important and responsible event that requires appropriate knowledge and skills. The following information about the error codes of the Ariston washing machines is given solely for informational purposes .. Making attempts to repair yourself, you will be solely responsible for possible further actions.

If you are not sure of your own qualifications, it is better to immediately contact the service center so as not to aggravate the problem.

When attempting to repair yourself, you will be solely responsible for possible further actions. If you are not sure of your own qualifications, it is better to immediately contact the service center so as not to aggravate the problem.

If the heating element breaks down

If a heating element (heating element) breaks down, the water stops heating to the set temperature, and an alphanumeric code may appear on the display, which notifies of the problem.

E6, E5

Errors occur when there are difficulties with heating the water. A malfunction occurs due to a breakdown of the heating element or due to violations in its power supply circuit.

HC2, HC1, HC

The main reason is the breakdown of the heating element, improper connection to the mains or a power outage. Initially, they check the connection of the equipment to the mains. If an extension cord is used, it is best to plug it directly into an outlet.

H2, H1

The appearance of the H1 sign signals a too rapid increase in the water temperature. If in a couple of minutes of operation the water warms up over 45 degrees, then a warning about the problem will appear.

HE3, HE2, HE1, HE

Highlighting the code HE3, HE2, HEi, HE on the display indicates the following defects:

• damage to any part of the internal electrical wiring;
• breakdown of the heating element;
• damage to the temperature sensor;
• incorrect connection to the mains.

Additional options

Hotpoint Ariston washing machines have a number of additional options.

• Additional rinse. Used to more thoroughly rinse out detergent residues from fabrics. The cycle time is increased by about 30 minutes.
• Spin. It is used if the laundry is not properly wrung out at the end of the wash. Runs within 15 minutes.
• Draining. Used if you need to urgently drain the water, for example, when a washing machine breaks down.
• Individual mode. Provides the user with the opportunity to independently set the parameters of their own program - temperature, spin, etc.
• Easy ironing (iron icon) - to prevent creasing during operation.
• Super wash. Function for removing stubborn stains. Increases the water consumption at the beginning of the cycle and the overall run time. When using this option, you can apply bleach and pour it into the appropriate compartment in the dishwasher.
• Quick wash. Allows to reduce the cycle time when loading lightly soiled laundry by up to 50%, depending on the selected mode. Thus, water and energy savings are achieved.

Recommendations on how to test on a Hotpoint Ariston washing machine: error F 05 and not only

Errors in washing machines Indesit, Ariston and other models can be: F 01, F 05, F 06, F 03, H 20, F 18, F 11, F 12.

When launching a test to identify an error, a number of actions are performed
:

1. The solenoid valve turns on, due to which water is poured to the main level, and then before the preliminary wash. Only 10 seconds are allotted for each period. time.
2. The hot water filling solenoid valve is activated for a period of 10 seconds.
3. The solenoid valve is switched on, which controls the water during the main and preliminary wash modes. After that, water begins to flow up to the mark until it is filled to the maximum.
4. The drum of the device begins to rotate clockwise, and then back.
5. The heating element is launched, which is responsible for heating the water to 30 ° C.
6. The drain pump is turned on and operation continues until the signal that the tank cavity is empty is triggered. At this time, the drum starts spinning in spin mode.
7. The test is over.

If during testing such errors as F 05 and F 08 were identified, then the indicator for testing will start blinking. The flashes will be slow with gradual pauses. Depending on the error code, it will be possible to detect the cause of the breakdown and subsequently begin troubleshooting. After repair, regardless of whether it is independent or in a service center, additional testing is needed to exclude the device from turning on if there is a problem.

Water level information

Samsung washing machine models are equipped with a special pressure switch that controls the filling of the drum with water. When the pressure switch does not receive the signal required to start work, the display generates an error.

E7

An encrypted error is notified by a water level sensor (pressure switch). The appearance of this alphanumeric value on the display is caused by a breakdown of the sensor itself or a violation of the integrity of the tube that connects the sensor to the drum.

1C

If the 1C code is displayed, then one of the following problems has occurred:

• breakdown of the sensor that controls the level of the incoming water;
• defects in connecting contacts;
• damaged, dirty or bent section of the tube belonging to the sensor;
• breakdown of the control system.

1E

The error code often occurs as a result of an elementary failure in the operation of the control system. Then it will be enough to turn off the household appliance from the network and turn it on again after 6 minutes. In addition, the error is caused by:

• discharge of the contacts of the control panel or pressure switch;
• problems associated with the pipe connecting the sensor to the pressure take-off tank.