What is snow removal equipment for walk-behind tractors and how to make it yourself

How to make a creeper for a motor cultivator yourself?

The first thing the manufacturer should do before starting the assembly is to draw up a work plan, focusing on the ready-made drawings. The diagram should indicate the methods of fastening the parts, their dimensions and shape.

Then you can start designing the creeper.

The procedure should be as follows:

The generator must first be prepared by the manufacturer. It can be taken ready-made from a Ural motorcycle. The generator must be completely serviceable, without visible damage and structural defects. The unit must combine a sufficiently high power and the ability to continuously create a stable torque;
Then it is necessary to cut the shell for the two required bearings. They are needed to complete the drive shaft. It will need to drive the gear, so the bearings must be able to withstand high loads and be protected from dirt and debris. When cutting out the shell, it is necessary to take into account the diameter of the gearbox used in the design;
Next, the manufacturer must select the bearings. Please note that the flange will be located on the back of the installed gearbox. A steel washer must be mounted in its inner plane;
After that, you will need to install the drive shaft of the cultivator. Then you need to fix the gear on it. The finished mechanism must be connected to the transmission unit and the shaft of the generator used;
At the end, the designer must securely fix the pulley and connect it to the driven shaft using washers and a spring nut.

How to make a snow blower for a walk-behind tractor with your own hands

Consider how to make a do-it-yourself snow blower. The attachment to the walk-behind tractor can be quite expensive for the user. Attachments for a walk-behind tractor cost more than 20,000 rubles. In order not to spend a lot of money, you can make a homemade snow blower for a walk-behind tractor. And to make a rotary snow blower for an all-terrain vehicle with your own hands, and auger. To make a snow blower for a walk-behind tractor with your own hands, you can take the drawings on the Internet, and then start assembling.

First you need to define the basic contours of the bucket using small metal corners. The frame is assembled using conventional welding. After that, it must be covered with aluminum or iron sheets. Remember that if you are using aluminum, it must be additionally secured with rivets and bolts.

For a self-made snow blower for a walk-behind tractor, the rear of the bucket should receive additional reinforcement so that a connecting element can be equipped on it. Installation is carried out using special strips of steel material. From the inside, along the side walls, you need to lay special bushings equipped with bearings for the auger shaft. For this, you can use any steel pipe.

In the center and along the pipe, it is necessary to make a slot where a metal plate is placed, which will serve as the impeller of the suspended unit and ensure the throwing of the snow mass into the outlet bell.

At the corners of the plate, you need to place the lugs in advance in order to subsequently fasten the screws there. Weld a key on one side of the pipe, where the transmission sprocket will be installed. In order for the key to be brought out, a hole must be made in the wall. After that, a snow plow auger is made: 2 pairs of rings are cut out of steel sheets, one side is cut on each one so that they can be opened.

The rings must be welded around the shaft.In order for the snow mass to be crushed, it is necessary to provide the rings with beveled teeth. At the end, install a socket, for which a steel pipe is fixed on the turntable.

The inlet must be securely fixed, and a good fan must be installed at its inlet, the role of which can be played by an old car stove. In order to feed the unit, it is necessary to install a generator that converts the power received from the rotation of the shaft into electricity. At the back of the bucket, make a mount on which the snow removal equipment will be hung.

The answer to the question of how to make a rotary snow blower for a walk-behind tractor with their hands, can be found on the Internet, including a video recording of the process. Do-it-yourself snow blower drawings for the walk-behind tractor are freely available. Attachments for motoblocks and motor-cultivators, made as a snowblower, will help to cope with heavy snowfalls and clear the area from snow drifts. Removing snow with a walk-behind tractor significantly saves time and labor.

Helpful hints and warnings

All bearings used must be sealed. This will help eliminate the risk of snow falling on their surface. Some materials can be purchased at the auto shop. They are especially important for driving the auger through the chain and belt.

This requires the following elements: bearings, pulleys and belts. In order to use as little force as possible when clearing snow, it is necessary to install the snow blower on the skis, as they glide best on a flat surface. If you are interested in building a unit from scratch, then we advise you to follow this link, which contains a diagram of a snow blower with your own hands.

Snow blower skis

With the help of the swivel chute, it is possible to adjust not only the direction of snow throwing, but also the distance at which it is thrown. It is its length that affects how far the snow will fly off. When working with a walk-behind tractor, you need to especially carefully monitor its internal structure.

Each time it is necessary to check that there is no blockage, as well as to immediately close up all kinds of holes through which snow or other elements can get into the internal structure of the system.

How to completely clear snow with a cultivator with brushes

Newly fallen snow or remnants of snow from large accumulations of this precipitation can be easily swept off the asphalt or other surface using a suitable snow blower attachment. For the complete elimination of snow, brushes with increased rigidity and the ability to constantly rotate are suitable.

Also, a rotating rigid brush helps to remove snow gently, that is, it does not injure or deform the coating during operation. Such a brush is usually mounted under a canopy, directly underneath on a rotating shaft.

With the help of such a brush, snow removal is carried out not only efficiently, but also quickly. In one pass, it is possible to achieve complete elimination of snow on an area of more than 1 m. The angle of capture can be made as it is convenient for the worker. There are three options for the location of the brush: left, right and center.

Rotating tokens

Attachments in the case of a rotating rigid brush can also be easily used to improve the comfort of conditions when cleaning snow, since the height of the brush can be adjusted at your discretion.

How to deal with large snow blockages?

If the snow is already wet or has been lying for a long time, it is impossible to completely remove it with rigid rotating brushes. You will need a special snow shovel. It has a suspended structure and is equipped with special knives to simplify the work.

If you use such a nozzle for a walk-behind tractor, it will look like a small bulldozer from a distance.In terms of technical capabilities, there are also undoubted advantages: loosening the snow layer with subsequent capture and transfer to the dump is very simple.

Special snow blower shovel

The bottom edge of the shovel must be upholstered with a rubber band. This helps to protect the road surface and the device itself from possible mechanical damage. The snow shovel is attached to the device using a universal hitch. The surface is cleaned 1 m wide at a time.

When working, it is possible to set the blade vertically, as well as move it in 3 directions. A walk-behind tractor that works with such a shovel can move at a speed of 2-7 km / h. Do not forget that this unit is designed for the Mole walk-behind tractor, but if you do not have this device in your arsenal, you can purchase a snow blower for the Neva walk-behind tractor, which is much more common in our country.

Extended and additional functionality of the device

The standard equipment of the device includes cutters and wheels necessary for transporting the model; in it, you can pick up additional attachments necessary for processing plots of land and carrying out specialized work:

lugs that provide full processing of the site;
a plow for cultivating virgin land and unplowed areas;
convenient and reliable potato digger for harvesting;
lawn crevice tool for arranging the local area;
hiller, for working with agricultural crops.

When choosing a functional attachment, it is necessary to make sure that it can be attached to the trailed part of a motorized device; for this, the characteristics of a motor cultivator are studied in detail regarding the method of operating the device.

Practical and reliable gasoline powered cultivators require a certain amount of care, organization of the correct storage method and timely technical inspection, which determines their further and effective service life.