How to attach a large mirror to a wall - here's a wizard

How to hang a mirror on hooks

The first method is suitable for mirrors with frames or small mirrors without them. As a rule, such mirrors already have some kind of attachments at the back, such as D-rings or hinges, and you just have to make a mating part for them - one or more hooks. In order to hang such a mirror on the wall, follow these steps:

Find out what material the wall is made of on which you want to hang the mirror. This will determine whether your wall can support the weight of the mirror and what screws and dowels you will need to use. For example, if you want to hang a mirror on a drywall wall, you will need special dowels, the so-called "butterflies".
Weigh your mirror. Depending on the weight, not only fasteners will be selected, but also hooks, since they also have restrictions on the supported weight.
Place the mirror against the wall where you intend to hang it. Use a pencil to mark the top and corners on the wall. You can also apply a level to the edge of the mirror before this and check whether it will hang vertically in this position.
You need to mark on the wall where the mounts on the mirror will be. to do this, measure all the distances from the edges of the mirror to the mounts, as well as the distance between them, if there are several. Then mark their location on the wall, transferring all measurements to it. If you have a small mirror with a wire or webbing loop at the center back, you only need one hole in the wall and you might even be able to do without a hook. To find out where this hole will need to be drilled, measure the width of your mirror and mark a point in the middle of this line. Then pull the loop up as far as possible from this point and measure the distance from its top edge to the top edge of the mirror itself. Transfer the result of measurements to the wall using the same pencil.
Mark on the wall where the holes for the hook screws should be - this can be done by attaching the hooks to the wall and aligning them with the markings for the mountings on the back of the mirror.
Drill holes in the marked locations for the screws to secure the hooks. Use a drill of the correct thickness for your wall material. If the wall material allows you to screw in the screw without a dowel, this is good. If not, drill holes just under the diameter of the dowels. Using them, screw on the hooks.
Before hanging the mirror on the wall, glue protective fabric pads to it at the back at the corners and centers of the sides - these are often sold in furniture stores, for example, for gluing on the legs of furniture so that it does not scratch the floor.

How to hang a mirror on a wall without a frame - Masters Club

A mirror is an indispensable element in every home. It would seem that difficult to install it? But when it becomes necessary to hang it, questions arise.

Now in stores there is a huge selection of mirrors: large, small, with designer decoration. Some of them have no fastening elements at all, which raises a logical question about installation. How to carry out the installation?

DIY fixing

Do-it-yourself installation does not require special skills, all existing methods can be done independently. The most common and familiar method is with nails. But they leave a mark in the wall, and later, if you remove the mirror, the hole will need to be repaired. Someone prefers the picture method: with the help of a special thread, it is attached to the surface.

Mounting methods

Kleeva.
On special holders.
For self-tapping screws for furniture doors or for fasteners with a plastic expansion joint.
With a decorative profile.
On the dowels, silt nails.

Installation recommendations:

in a room where there is little light, install a mirror opposite the window. It will make it lighter;
a large canvas will visually expand the room;
it is not advisable to place in the kitchen in the area of the stove;
in the children's room, it is better to cover the mirror with a protective film, if it breaks, then no one will get hurt;
it is convenient to place the canvas in full growth in the hallway;
the direction of the light should not be straight, otherwise the canvas will quickly fade.

Installation without drilling

only a flat surface is suitable for fastening. If the wall is defective, then the product will be in a tense state and may eventually burst;
this method of attachment is not suitable for glossy surfaces and in the bathroom, because it is not resistant to moisture and will begin to peel off over time.

Choose quality glue, well-known manufacturers - "Crassus", "Zubr", "Ravak".

How to hang a dowel mount

At home, attach the canvas to the desired surface, make marks at the attachment points. Using a drill, choose a concrete nozzle, make a hole up to ten millimeters deep and secure the sleeves.
Next, attach the mirror and screw in the metal screws.
Install the clamping elements.
Plugs are placed on top.

After finishing work, check all elements for strength. Everything must be stable.

If work is performed on a surface decorated with plasterboard, then you need to use special butterfly dowels. They have longitudinal ribs that prevent the dowel from turning, and the locking bolt holds and prevents the mount from falling into the wall.

In the same way, the canvas is attached to a fishing line or rope. First, dowels, anchors or hooks are installed, and then they are suspended.

How to attach without nails

A canvas without a frame can be fixed in several ways:

Kleeva. The working technique is the same as with mirrors with a frame: prepare the surface, level it, remove dust, make markings and install. This method is suitable for partial wall decoration.
Profile. The blade is inserted into a metal profile. It is so convenient to arrange large surfaces. Technique of work: surface preparation, profile installation, a silicone seal is applied to the edge of the glass to make the mirror easier to fit into the grooves. The canvas is inserted and pressed to secure. All other parts are installed by analogy.

Installing large mirrors: features and recommendations

It is better to entrust the installation of large mirrors to a specialist, as this requires skills. The installation method depends on the size and characteristics of the canvas. The main method of fastening is with hardware, special fasteners.

Use glue that has not expired.
Do not touch the mirror for several days so that it is fully fixed.
Prepare the surface correctly: level and eliminate defects.
Attach a heavy-weight mirror additionally mechanically. You can add small fasteners or make a small stand.

How to stick to a wall with wallpaper

It is better to install a mirror on a surface with wallpaper using fittings, this will ensure safety.

For this, special fasteners are used in the form of brackets with lining. The canvas is fastened in staples, and the linings act as a seal.

Is it possible to hang a full-length mirror on the wall without fixing

You can install a full-length mirror with the help of silicone sealant or glue, the technique of work is the same as with the glue method.

Mirrors in the interior are an essential element of any apartment. Choose a place for installation in advance, carefully approach the installation process.

Liquid nails for mirrors and other installation features

The role of mirrors in human life is very diverse, it serves us to assess the appearance, is a decoration of the room and is even used in magic.Let the sorcerers ask the last question, but we will consider the most popular installation methods.

Step 1: choosing a location

Whichever method of fastening is chosen, it all starts with the selection of the most suitable place. Thus, keep in mind that the light should fall on the face, and not on the object itself. To make it last as long as possible, you should attach it as far as possible from heat sources. Well, the mirrors in the bathroom, which are located above the sink, must be installed at least 20 cm above it, otherwise the surface will be dirty all the time from water drops.

Step 2: Buying a mirror

If you want to see your reflection at full height, then the accessory must be at least 140 cm in height. Having bought a mirror 60 cm high, you will see yourself up to your waist. Well, the most common examples for latrines are usually about 40 cm.

Step 3: Choosing a mounting method

1. Liquid nails for mirrors, mounting glue or special double-sided tape will ensure reliable attachment of the accessory without damaging the wall surface. You just need to decide on the place and apply glue on the back surface of the mirror in strips no more than 7 mm wide with a step of 5 cm, for this you need a mounting gun. The distance from the last strips to the edge should be 4 cm. We apply the product to the wall and press. Then do not forget to remove excess glue that has come out on the sides. In general, different products do not always have the same application technology, therefore, before starting work, be sure to read the instructions on the package.

2. Mounts for a mirror without drilling the product itself, as well as other accessories, require drilling a wall, so you need a puncher. Having made a preliminary marking on the surface, we make a hole into which it is necessary to insert a dowel. Note that the holes in the wall must line up with the mounting holes on the accessory itself. It is imperative to install rubber pads between the mirror and the wall, as well as its face and the plug, so check that they fit in the kit.

3. If there are no mounting holes in the product itself, then you need to familiarize yourself with how to drill a mirror. This work cannot be classified as simple, but it is quite doable, only a diamond drill is needed. To prevent cracks or other defects from appearing on the surface, it should be constantly moistened with water in order to prevent heating. Then, after grinding the holes, you can proceed directly to the installation.

Another popular method for installing mirrors is flush with the tiles; in this matter, it is very important to choose its thickness. It must match the thickness of the tile

Having leveled the place where the mirror will be installed with putty, you need to tackle the curb, first the lower, then the upper, and last of all the sides. Install the accessory only after the curb tiles are securely attached. Next, with a ribbed spatula, apply a thick layer of glue to the wall and attach the bottom edge of the product, not forgetting to insert crosses between it and the tile. Then we press the rest of the mirror so that it is flush with the tile, and keep it in this state for fifteen minutes. After removing the traces of glue, we rub the seams.

Accommodation guidelines

When choosing a way to mount a mirror, based on the material of the wall, its reliability, do not forget about the place in which this mirror will look most advantageous. It is no secret that sometimes it is not possible to place the mirror sheet where you want. The reason may be the design features of the premises, the lack of footage.

In small apartments, each piece of furniture has its own place, which limits the space for the mirror itself

To simplify the task, you can pay attention to some nuances:In a small darkened room, it is worth placing a mirror opposite the window opening to give more light to the room.

A mirror on the entire wall of the bedroom will move the small room twice

In a small darkened room, it is worth placing a mirror in front of a window opening to give more light to the room. A mirror on the entire wall of the bedroom will move the small room twice.

You should not hang a glass product in the kitchen by the stove: high temperature and fumes will provoke frequent leaving, will affect the appearance of the mirror.
Before hanging the canvas-panel in the bathroom, cover its ends and back with a special sealant.

Place stylized lighting fixtures near the mirror in the corridor on the wall, this will visually expand the walls in the room and give a stunning effect of diffused light.
Do not hang decorative elements of this type at an angle to the vertical surface, so as not to distort the reflection.
To correctly fix the mirror in the hallway, choose a place where you can look into it in full growth and note that this distance should be at least 1-1.5 m from you.

The canvas, which has a height of 0.6 m, guarantees a view to the waist, a product from 1.2 m - a full view of the entire figure. The choice of mounting height for the mirror in the hall will depend on its height and width. The bottom of the full-length mirror should be no more than 0.5 m above floor level.
It is necessary that the wall for high-quality gluing of the mirror is even. A thin piece will adapt to the shape of an uneven wall, since the glass can take the shape of the base. To stick the product correctly and avoid such a nuisance, you need to pick up thick glass or level the wall.

Height above sink

The general principles for placing a mirror reflective element inside a bathroom are:

the top edge is 10 cm higher than the tallest member of the family;
the lower edge at the level of 15 - 20 cm from the side of the sink to avoid constant splashes, streaks, stains;
width in the size of plumbing or slightly less;
glass thickness from 2 mm, otherwise the mirror will be too fragile, but no more than 10 mm, so as not to make the structure heavier.

However, there are nuances in which even these principles are not correct:

a reflective element can be used in the interior to visually increase the working space;
Preschool children may need a lower setting, level with their face.

Small-format magnifying makeup mirrors must be attached taking into account the degree of mobility and the number of hinge elements.

On a brick base

For installation using glue, prepare the surface - if necessary, remove the wallpaper, carefully level it with a primer, followed by grinding. Be sure to clean, wipe with an alcohol solution.

Special glue for amalgam coated glasses is used according to the instructions. It is applied to the surface not in a continuous array, but in parallel stripes at regular intervals or in "thick" drops in a checkerboard pattern.

Then the product is pressed tightly, held for about a day until complete set.

If, when deciding how to attach a mirror, this method is chosen, you need to remember what to remove or outweigh it will no longer work. This is the last place of his "stay" - then you can only break, remove.

When using thick double-sided tape, the surface is prepared. It is glued on the back side of the glass along the perimeter and surface with vertical or horizontal stripes with a step of 5-7 cm. After that, the protective film is removed from it, and it is pressed into place.

All this can be easily done by hand.

The composition of liquid nails allows you to reliably hang the mirror, while not spoiling the decorative surface of the installation site.In terms of strength, this construction glue is significantly superior to PVA glue, and some modifications are equated to the characteristics of dowels.

The option is very convenient, since there is no need for tools and fasteners, you only need a suitable glue.

The surface of the wall, freed under the mirror, must be flat, otherwise the mount will be unreliable.

With the help of hardware, they usually make fixings for a mirror that has ready-made holes. To do this, it is required to drill recesses in the wall along the diameter of the used dowel 5 mm longer than the length of the self-tapping screw that is planned to be used. After drilling, they are cleaned of dust, dowels are installed, the product is attached, screws are screwed in turn. Be sure to cover with decorative heads.

When hanging a mirror, you need to pay attention to the shape of the interior element.

Installing the mirror on dowels and screws

Fasteners of this type are capable of supporting any mass. So, if you wish, you can even fix the canvas to the entire wall, starting from the ceiling. Mounting accessories can be purchased at any hardware store.

Of the advantages of this installation method, the following can be distinguished:

the strength of the fasteners;
long service life;
the ability to install anywhere.

Installation technology

First, we need to make holes in the mirror sheet for through fasteners. So, there are some ways that make this process easier:

It is necessary to first rub the mirror with turpentine, and only then drill - this will avoid the appearance of cracks.
It is better to pre-make holes in the right place using a diamond glass cutter.
During work, do not press too hard on the drill. All actions must be as careful as possible.
It is recommended to use an electric drill with adjustable speed, because the mirror will only need to be drilled at minimum speed.

Step-by-step instruction

Step 1. First of all, we process the surface and let it dry normally. In this case, the mirror should be placed on the most flat surface. Next, you need to make a marking for the hole using a marker.

We put markings on the canvas

Step 2. Next, around the future hole, you need to make a small rim of plasticine, where you can pour water, and only after that you should start drilling.

It is important to ensure that the drill is always in the water. So it will overheat much less.

Step 3. When the hole is ready, it will need to be sanded with sandpaper.

Sanding the hole with sandpaper

Next, you will need, as in the previous case, to make holes in the wall, and then place the fasteners there and only then install the canvas itself.

How to hang a mirror - the correct location and design tricks of mirrors and mirror surfaces (105 photos)

Mirrors not only reflect faces, hairstyles, clothes, but are one of the effective elements of the interior, making it richer, more elegant, more beautiful. Mirrors can visually increase or decrease the area of the room in which they are located. So, for example, a large wall mirror, or several small ones, will make the room brighter and more spacious.

The appearance of the room, its mood and lighting depend on where the mirror is located, in what frame, what shape it is.

A little about mirrors

Mirrors have long been an integral part of home interiors. They affect the lighting and the size of the room in which they are located. Also, they are used as a kind of decor that decorates the room. And of course, mirrors are necessary for a person in everyday life, for their intended purpose, that is, reflections of the surrounding space, objects, people, animals.

The mirror is glass, treated on the back with a special coating, amalgam. There are aluminum and silver amalgams. Mirrors with aluminum amalgam can be positioned in the hallway, bedroom or living room.

Silver amalgam is good in the bathroom, where due to the temperature difference, mirrors with aluminum amalgam constantly sweat. True, such a mirror will cost much more.

How to fix the mirror

There are several different methods, depending on where, what or what you want to attach the item to. There are several ways to mount the mirror, but choose the most suitable one

First of all, they pay attention to the materials from which the surface is made, where they are going to attach the product.

Here's how to hang a mirror on an unframed wall:

Glue (the surface is leveled as best as possible, use glue "Liquid nails", special or glue-sealant. Carefully read the instructions to choose the glue in accordance with the material from which the surface is made. It must be indicated that it is suitable for mirrors ).
Purchase special fasteners for mirrors.
Install special holders on the wall.
You can drill holes directly in the mirror, and stick in the self-tapping screws. But it is even better to buy special plastic expansion joints for fasteners that are available for sale. They will not allow the mirror to be pulled over, and will keep it from cracking.
Double-sided tape (in this case, use a special mounting tape M3. Apply if the mirror is not heavy).
The mirror is attached to the decorative profile (here the lower edge is lowered into the profile itself, and the upper one is attached using one of the above methods).

How to install a mirror on a tile

There are several ways to hang a mirror on a tile. For example, secure with dowels. Calculations are made in advance, and markings are applied to the wall. Then they drill, insert the dowels into the holes, screw on the fastening accessories. After that, the mirror is inserted into the grooves, and decorative plugs are put on the clips.

Here, options using glue and tape may also be suitable; for this, simply dismantle the tile at the location of the mirror. The “Liquid nails” glue is suitable for the tile. Many people prefer to order a mirror with holes, and hang the mirror on the lamps.

You can also install fasteners in the form of staples. Almost all tile work requires drilling. Drilling work is performed with a drill or diamond drill.

Numerous photos in our gallery clearly show how you can hang a mirror in the bathroom.

Mirror with frame

It is easier to install products with frames on the wall than without frames. Usually, in the frames themselves, there are already special slots that are put on the dowels. On the wall, markings are required from the bottom so that the mirror is level and does not warp. If there are no slots, you can make them yourself.

If there are holes in the frame, the mirror is attached to screws using special holders. Also, you can contact a glass workshop and order a product with slots in the frame for mounting to the wall (or to the cabinet), or with holes in the mirror itself, along the edges. It remains only to drill holes in the wall, and use dowels with self-tapping screws for installation.

If the mirror is large, then the plinth is necessarily stuffed on the floor. To prevent the mirror from falling down into the slot, you can additionally install the wort and a plastic corner on it for protection.

Then they act according to the usual scheme: calculations, marking, drilling and fastening. You should be careful about fittings and materials so that they do not cause cracks.

A baguette, a frame, if you wish, you can do it yourself. Then the mirror will fit into the interior much more harmoniously.

Using double-sided tape

A miniature product can be easily fixed on the wall using double-sided tape, on both sides of which a special adhesive is applied. The thickness of such tape can be different, but on average it is about 10-20 millimeters.

Installation technology: step by step instructions

It is with this method of installation that even a beginner can cope, because all the steps for installing the product are very simple.

Step 1. On a clean mirror sheet, it is necessary to fix the scotch tape in pieces. Do not cut off large strips. It is better to place small pieces all over the canvas (as shown in the image).

We glue the scotch tape to the mirror sheet

Step 2. Next, you have to glue the mirror on the wall using preliminary markings, as in the previous case.

It is necessary to remove the protective layer from the double-sided tape and attach the mirror to the wall

The following advantages of using double-sided tape when mounting a mirror can be distinguished:

it is possible to remove the canvas at any time and fix it in another place;
scotch tape is inexpensive, while very little is required;
it has good resistance to temperature extremes;
using this tape, you can hang the mirror on any surface.

According to the manufacturers, tape can be safely used even for fixing medium-sized mirrors. Despite the ease of installation, this is a fairly reliable mounting method.

Among the disadvantages of double-sided tape are the following:

the mirror will not stick to an uneven wall;
it is not advisable to abruptly remove the tape from the mirror, otherwise the coating may be damaged.

How to attach a mirror without a frame

Several options for fastening the product are known. The most important factor is the condition of the wall surface. The simplest is the technology using a special glue (double-sided tape). This technique is most effective when the wall cannot thoroughly hold the nails (drywall, foam blocks).

You can fix the canvas with special holders, use beautiful decorative profiles. To install the fittings, you will need self-tapping screws or strong dowels. To fix the canvas, first the lower brackets are installed, then all the others.

Features of mounting a mirror on walls made of different materials

Sometimes walls are made of materials that do not have high strength. It is simply impossible to carry out a permanent installation on them. Therefore, each material requires an individual approach. For example, for working with drywall, glue techniques or the installation of dowels - butterflies are considered the most preferable.

Concrete surfaces

The process of attaching the canvas to this material can be almost anything. The surface of the wall is first prepared. If work with glue is expected, priming work is required.

Concrete walls are highly durable. Therefore, a powerful hammer drill is required to drill a hole.

PVC panels

This material is often used to decorate walls (for example, in a toilet). It is very difficult to fix the product on PVC. The holes will not provide a secure fit. The best option would be to use silicone glue. But, at the same time, in addition to the characteristics of the wall material, it is required to take into account the dimensions of the mirror, the acquired fittings.

Brick wall

Before starting work, surface preparation is performed. The wall is cleared of dirt. Then it is primed. The mirror can be mounted in any way.

If it was decided to use glue, you must always remember: after the installation is completed, it will be impossible to remove the canvas

You need to use glue carefully, strictly adhering to all points of the instructions. No need to spread glue on the entire surface of the product

The simplest way is to fix it with double-sided tape. First, the surface is degreased. Paste in strips every 8 cm. Then the protective film is removed, the product is pressed tightly to the prepared surface.

Installation in other ways is carried out using the above options.

Tiled surface

Tile refers to a specific material that does not drill well.Therefore, the best way to attach a mirror is to glue it on. The glue should be characterized by maximum moisture resistance.

For the operation, it is best to use a silicone sealant. In addition to moisture resistance, it is not afraid of temperature surges. To install a mirror in the bathroom, it is desirable to leave the location of the product without cladding.

You do not need to completely remove the tiles. If you choose the right glue, thoroughly prepare the surface, clean it from dirt, fatty deposits, the connection will turn out to be quite reliable.

The task can be performed using various hardware or special holders. It is advisable to choose the size of the fasteners so that they can be easily installed between the tiles.

Plasterboard walls

If the mass of the mirror exceeds 10 kg, you should not hang the product on such a wall. Drywall is very fragile, it is considered a very unreliable material. Therefore, the best installation option is glue, together with construction double-sided tape. If you plan to dismantle the mirror, you need to install a butterfly dowel (with glue, this operation will not be possible).

Walls with pasted wallpaper

To fix the canvas, you should not use glue, double-sided tape is not suitable. An exception is a mirror weighing less than 2 kg. But it is better to use mechanical fasteners:

holders;
strips;
hooks;
brackets.

Of course, fixing the mirror yourself is quite difficult, but doable. Before starting the operation, you need to be well prepared. Perform an accurate calculation, measure the installation site, purchase the necessary tool

It takes patience, attention and accuracy to get a good result.

Mirror Furniture

Non-standard ways

In addition to the standard, well-known methods of mounting shelves, original options are used using various materials at hand. These details make it possible not only to conveniently and easily fix the structure, but also act as a decoration.

Hook rings

You can hang the shelf using rings with attached hooks. The rings are attached to the wall, and the hooks are hooked to the hinges previously screwed into the fabric of the structure.

Water pipes

The method will come in handy in any room. Holes are made in the fabric of the furniture slightly larger than the diameter of the water pipe. The shelf is "put on" and fixed with a flange in the desired position. The structure can consist of one panel, or it can be an open rack.

Belts

The shelves, suspended on belts, look original. To do this, take two leather products of the same length, fold them in half and drill them to the wall. A shelf is inserted into the resulting loops. To prevent the canvas from moving, the belts must be screwed with small screws to the shelf.

Ropes

Shelves hung on ropes will look great. For this, a thin rope is used. 4 holes are made in the tree, through which the rope is threaded. Knots are tied on both sides, so the shelf is fixed. The ends of the ropes are tied together and attached to the wall.

Hidden fasteners in books

The shelf is an old book with a metal corner screwed into it. The second part of the mount is fixed to the wall. Such a shelf will hold several more books.

Basic ways to hang

There are eight common ways to hang mirror structures that you need to become familiar with.

Special glue

Most often, products are attached to the walls using special fasteners, but they cannot always be installed. For example, problems can arise when hanging from a drywall wall. In such cases, it is better to use adhesives that can withstand a load of twenty kilograms. The main advantage of using such tools is that a person does not have to drill the surface of the wall.

Holders

Some people do not want to use glue and therefore use holders instead. There are two types of such devices available:

Non-cut. These are universal fixtures that can be installed on doors or walls. A feature of the structures is that they are tightly screwed to surfaces.
Through. When installing such products, a gap of 5-7 millimeters is made between the mirror and the wall.

Self-tapping screws or fasteners with plastic expansion joints

People often use self-tapping dowels to hang mirrors. This method is considered the most common, as it will suit most types of walls. However, for plasterboard surfaces, it is better to use a different mounting method.

Decorative profile

A decorative profile is a material that is used for cladding window slopes, columns and walls. It is also used to attach paintings, mirrors and other products to concrete or brick surfaces. Such products are made of metal, wood or plastic.

Using special tape or mounting tape

To quickly fix the structure to the wall, you can use mounting tape or double-sided tape. The main feature of such products is that they are covered with an adhesive composition on the inside and outside. This allows the material to be used for gluing any surfaces.

Staples

The mirror can be wall-mounted with brackets. Using such a fastening material, it is necessary to place a special fiberboard substrate under the mirror structure. The product is then stapled to the wall and backing.

Hangers

It is no secret that various mounts are used to mount mirrors. Special suspensions are popular, which are suitable for rooms made in Art Nouveau or Techno style. Such fasteners are made of chrome-plated metal, but there are also wooden hangers.

Hidden plate

Some people want the mirror mount to be invisible. To do this, use special plates that hide all the connecting elements. It is recommended to use such fasteners if the mirror structure will be installed in the bedroom or in the hallway.

What is a mirror

In the manufacture, sheet glass is used, obtained from a mixture of sand, soda, limestone, and other materials. They should contain a minimum amount of iron salts, which impart unnecessary tints to the glass.

A modern glass mirror is well known to everyone and is a sheet of polished glass, on one side of which a thin layer of metal, called amalgam, is sprayed on.

The initial mass is boiled, fired, a sheet is formed, polished, and cut with diamond rollers. A metal coating is applied so that the surface reflects light, and is protected with varnish.

Aluminum is applied in the manufacture of budget mirrors, and silver is used for expensive ones.

When choosing a finished product, the thickness of the glass is taken into account, the quality of the coating on the back side is uniformity, the absence of stains, and other defects. The degree of distortion of the display is taken into account - it happens that the mirror "makes" or "slims" - they choose according to their taste

In everyday life, it satisfies the physiological need of a person to see himself, is an element of the interior that allows you to change the perception of space.