How to clean the seams between tiles in the bathroom at home: how to wash and bleach

How to descale tiles: tips and tricks

Most industrial cleaning products contain acid, they are considered the best in the fight against limescale. Folk recipes involve the use of vinegar or citric acid. In large quantities, all these funds partially destroy the grout in the tile joints and the tile coating.

Chlorine or chlorine-containing preparations can change the color of tiles and joints. They also need to be used only in advanced cases, for example, if, in addition to lime deposits, a fungus is observed. Powders with baking soda also work well, but with intense friction they will scratch the tiles.

It turns out that most of the common methods of cleaning tiles from plaque are harmful, so what to do? You can take a closer look at expensive, gentle drugs, or you can carry out an eradicating cleaning once and prevent the appearance of plaque in the future. Remove moisture from the walls, and to prevent condensation from forming, take care of good ventilation in the bathroom.

How to properly clean bathroom tiles

Even experienced housewives make mistakes when cleaning the bathroom. Incorrect actions often lead to various damage to the tiles, which cannot be fixed. We will study the basic rules for washing tiled flooring:

The tiles are cleaned only with soft washcloths and brushes; melamine sponges are also suitable. After washing, all surfaces must be wiped dry, for this, microfiber napkins and towels that absorb moisture well that do not leave lint and streaks are isolated, you can use viscose, cotton or terry cloth. Liquid products are easier to apply from a spray bottle. The tiles on the walls are washed from the bottom up. Rinse and wipe the walls from top to bottom

It is important that there are no particles of cleaning solutions and moisture on the surface. You should prepare for the fact that after the first procedure, the plaque will not be completely washed off.

It is advisable to repeat the cleaning immediately, later it will be much more difficult to wash off the softened and again dried dirt.
When reprocessing, attention is concentrated on the areas where the spots remain. Work is carried out in rubber gloves, any drugs and household products can severely damage the skin of the hands
When using chlorine or ammonia, be sure to wear a mask. In case of contact with skin or eyes, rinse immediately with running water.

Cleaning tiles with a convex pattern has its own characteristics, such a surface can be washed only with products with a soft texture without abrasive particles. Some housewives use a steam cleaner. The results, of course, are not bad, but after such treatment, it is recommended to additionally treat the tile with a glass cleaner (marked with anti-steam).

For prophylactic weekly cleaning of the tile, dissolve liquid soap or dishwashing detergent in warm water, apply evenly to the walls, and leave for 2 minutes. After that, the tiles are thoroughly wiped with a brush and washed off with running water. The amount of soap is calculated independently, it all depends on the area of the tiled coating, the main thing is that the solution foams well.

How to whiten seams with solutions based on folk recipes

Seams can be cleaned using specialized chemical compounds, which will preserve the appearance of the seams for many years. But such effective drugs are not always safe. Therefore, it is worth considering how to prepare special compounds for cleaning seams at home using the ingredients at hand.Giving trowel joints to their original appearance takes not only time, but also effort. Periodic cleaning of the seams with a solution of lemon juice, mustard, vinegar, ammonia, soda and fine table salt will keep the seams whiteness.

Bleaching with compositions prepared on the basis of folk recipes will allow you to clean the seams and the surface of the tile at the same time. All components of the solution are environmentally friendly substances that do not contain chemicals. The composition below will allow you to clean not only tiles, but also any plastic surfaces, for example, windows. This remedy is most effective in whitening.

To prepare the solution, use:

Folk remedies for bleaching seams and tiles.

Water (more than 7 glasses of equal volume 200 ml).
Lemon juice (1/3 cup).
Vinegar 9% (50 ml).
Baking soda (100g).

The entire mixture must be thoroughly mixed until all ingredients are completely dissolved. If the mixing process was correct, then the final result will not be long in coming.

Stirring must be done with gloves. Take water and add lemon juice, then vinegar. After that, gradually add the baking soda while stirring the mixture gently. The addition of soda will be associated with the onset of a chemical reaction.

All windows of the room during the creation of the solution must be open. The container in which the mixture will be prepared must have a large volume. This is necessary so that, as a result of the reaction, the foamed mixture cannot leave the container.

Necessary tools and tools

It goes without saying that you should not clean dirty floors with your bare hands.

Therefore, you need to stock up on the following items in advance:

doormat;
hard old brush for cleaning teeth;
broom for sweeping the floor:
a few rags:

clean warm water;
hydrogen peroxide;
vinegar or citrus juice;
soda;
salt;

solvent;
mustard powder;
ammonia;

whitening cleaning agent with abrasive particles;
small metal hard sponge;
old small knife.

Not all of these items may be needed to clean the seams, but only a part of them. The choice of a specific cleaning method should be selected based on what led to the appearance of dirt in the seams.

Five affordable folk ways

Slightly soiled cracks and cracks in the tiles are easy to clean, so you can safely throw chemicals away into the closet and pay attention to safe and gentle folk remedies. Most products can be found in any home

How to whiten gray gaps in a tile:

Soda is the first product that comes to mind when you mention traditional cleaning methods. To wipe off the dirt, sodium bicarbonate is scooped up with a damp toothbrush and the seams are treated. Careful with tiles! Try not to touch it to avoid micro-scratches.
To enhance the effect of soda, a little "Whiteness" is added to it, a thick gruel is prepared from the components. To clean the gaps, the paste is applied with a spatula to each seam and left to dry completely. Then the product is washed off with water using a sponge.
Vinegar also increases the effectiveness of baking soda. In order to rinse the tiles, you will need two mixtures: 3 parts of baking soda + 1 part of water and a solution of vinegar and water in equal proportions. First, a soda paste is applied to the seams. Acetic solution is sprayed from the top of the spray bottle. The reaction begins. After the bubbles are dry, the seams are brushed off. Dirt and soda residues are washed off with water.
Lemon juice has long been known for its bleaching properties. The substance will complement the action of baking soda and vinegar. The product is prepared by mixing 0.5 cups of water, 3 tbsp. l. soda, 0.5 tbsp. l. lemon juice and 0.25 cups of vinegar. The baking soda will begin to react by forming bubbles. To clean the seams, the solution is applied generously with a brush. After the first layer has dried, the second is applied. When the dirt comes off, the cracks are rinsed with clean water.
Mustard Powder Cleansing Recipe: Half a glass of baking soda, a third of a lemon (juice), 1 tsp. any toothpaste, 1 tbsp. l. mustard. The components are mixed and diluted with 1 liter of water. The solution is applied to the seams with a sponge and left for up to half an hour, depending on the degree of contamination, and then washed off with water.

How often should seams be washed to keep them clean? Tile care must also cover the gaps. If you pass them at least once a month, the fungus will not take root. If the mold grows faster, and every 3 days the seams are covered with characteristic blackness, you need to urgently check the draft of the ventilation, clean its grate, preferably install a fan or a hood.

Choice of cleaning agents

A steam cleaner (steam generator) can be used. The steam escaping from it under high pressure quickly and thoroughly cleans the tile joints. Hot steam kills harmful microorganisms and softens dirt.

The range of household cleaning chemicals is very extensive, most of the products can be successfully used to clean the tile fugue from contamination. In total, three categories of suitable formulations can be distinguished:

Combined universal kitchen and bathroom products from manufacturers such as Mister Muscle, Domestos or Cillit. The type of detergent should be selected based on the nature of the dirt: grease, dust, dirt, limescale. These products are good because they are supplied ready-made and in a sufficiently strong concentration, nevertheless, some may be confused by the high cost of such household chemicals.

It is important that the cleaner has a neutral or high PH: the acidic environment destroys the joint filler and leads to increased porosity. Self-prepared compounds or household chemicals that do not have such a direct purpose as cleaning tiles

Starting with chlorine and oxygen bleaches, ending with glass detergents, washing gels and hand washing paste for car refiners. Often, when cleaning seams, there are areas with particularly heavily ingrained dirt, where you have to select a cleaning agent by a test method. Self-prepared formulations based on baking soda, ammonia and whiteness are also quite effective, they are less expensive and therefore more popular.

Specialized fugue solvents are used in two cases. The first - if the bevels of the tiles were not properly cleaned from the remnants of the aggregate and constantly spoil the overall picture of the joints. Also, cleaners of this kind can be used when stubborn dirt does not lend itself to any of the available cleaning methods: in these situations it is better to remove a thin top layer of material to renew a fresh, unstained surface.

Removing mold

Another enemy that is extremely difficult to overcome is black mold. Its disgusting growths on the walls and floor between the tiles are able to cross out even the most expensive and sophisticated bathroom renovations.

There are several methods that can get rid of this blackness. Let's start with homemade recipes, because many housewives do not welcome the use of chemicals in everyday life, for fear of harm to health. Plus, homemade methods are much more economical than buying expensive detergents.

The most effective recipes for killing mold:

A paste of soda and chlorine powder. Whiteness or any other cleaning powder containing chlorine will do. The resulting mixture of soda and whiteness effectively brightens and disinfects the surface. But as mentioned above, bleach-containing blends are not suitable for colored seams. Wear gloves and a face shield when handling aggressive chemicals such as chlorine. The mass is applied with a spatula to problem areas before drying. Then all this is washed off with water.
Citric acid, soda, and vinegar. Another working household method for dealing with mold is a solution of water, vinegar, citric acid, and baking soda.If the moldiness is insignificant, then you can treat the lesions with vinegar without dilution, then rinse.
Ammonia. Dissolve two tablespoons of ammonia in two liters of water. Then spray the solution onto the affected area. After a quarter of an hour, walk with a damp cloth and wipe dry. The antimicrobial effect of ammonia will help get rid of black plaque.
Steam. The steam generator will help to cope not only with dirt, but also with mold. The device delivers hot steam under pressure, which softens and pushes dirt out of the tile joints, and the high temperature destroys mold and mildew.

Household chemicals

It is not always possible to get rid of blackness with home methods, and then it is worth turning to specialized means aimed at combating mold. Household chemicals do not always give the desired results, and there is little pleasant in the smell of vinegar and bleach. Today, you can buy many effective products that will get rid of mold and protect against its appearance in the future. The most popular remedies include:

Atlas Dolphin is a protective emulsion, it does not clean, but creates a film that prevents the deposition of dirt and bacteria. It is applied immediately after grouting or after cleaning the seams. This protection will help keep your bathtub clean.
Bozo is a concentrate that removes lime and rust, disinfects and removes odors. It is diluted in a ratio of 1 to 4, but the fungus is directly processed with a pure concentrate.
Mellerud is an excellent product for the maintenance of bathroom tiles. Quickly removes soap and lime stains while refreshing grout and tile color. For routine cleaning, it is recommended to dilute 125 g of the product in a bucket of water. For stubborn soiling, use without dilution.
"Snowball" is a special pencil that whitens seams and kills fungus. The remedy is effective for shallow lesions.
The melamine sponge is not an absorbent cleaning item, as you might think, but a detergent. It is a kind of eraser that erases dirt and erases itself. It is enough to wet the sponge and try to clean off the dirt with it.

All these substances are much stronger and more concentrated than home components, and this is certainly a plus, and a minus is their high toxicity, so it is better to work in a respirator, providing ventilation of the room.

In advanced cases, more serious measures are needed, since the fungus managed to settle deep in the grout. The best thing, of course, would be to remove the old tile, clean and disinfect the surface, and put in a new one. If major repairs are not included in the plans, then you will have to deeply clean the seams.

Grouting is tedious and hard work, but worth it. The work can be carried out with a spatula, but it is better to use a drill with a half-disk nozzle, this will somewhat simplify the task. Before work, the tile joints must be moistened with water and vinegar so that the grout becomes more pliable. After that, the joints need to be washed, dried and treated with antifungal agents, and then wiped again.

Recommendations: how to clean the bathroom tiles from mold

Mold often develops in bathrooms, forming not only at the joints of tiles, but also completely covering the walls. It is necessary to start fighting it at the initial stage in order to protect yourself and your loved ones from negative effects on health.

The causes of fungus and mold:

Incorrectly laid tiles;
Constant high humidity in the room;
Lack of antiseptic treatment;
Cleaning too infrequent;
Lack of ventilation;
A favorable environment for the development of microorganisms.

If you decide to independently clean the tiles in the bathroom from mold, then you should definitely prepare a mask and a special brush and washing solution in advance.

Ways to get rid of mold:

Cleaning with a steam cleaner will destroy all microorganisms and also remove grease, dirt and limescale.
Whiteness or a solution of bleach will help you forget about the problem for a long time if you apply it and leave it on the walls for 30-60 minutes, and then rinse with clean water. The procedure will be accompanied by a strong specific smell, so you need to protect the respiratory system. The room should be well ventilated.
Cleaning the seams with a stiff brush and soda ash will also give excellent results.

But this must be done carefully so as not to scratch the tile.
If any methods prove to be ineffective, then all that remains is to change the grout between the joints. It is recommended to treat everything with an antiseptic and use only a special bathroom grout with special additives.

To whiten the seams, you can use hydrogen peroxide, which can be applied to the surface and not washed off.

General recommendations

How to clean the tiles in the bathroom from plaque? Which means to use depends on the degree of contamination and the type of material.

For example, formulations containing chlorine do an excellent job with mold and yellow bloom. Also, in these cases, use 72% laundry soap. Light, recently appeared contamination is washed off with a soda solution, soda and citric acid. But to remove rust from tiles and limescale, products that contain concentrated acids are used.

Tips to get rid of dirt quickly:

Old rust or limescale can be removed with acid-based products. There is no need to be afraid that the surface of the tile will be damaged, since this material is resistant to all kinds of chemical influences. However, it should be remembered that acid-containing compounds can damage the grout in the joints between the tiles, therefore, aggressive agents should not be applied to them. Stick the tape on this area before use, and peel it off when finished.
It should be remembered that chlorine-containing compounds can harm colored tiles and discolor them. Therefore, such products must be diluted with water.
Do not use metal scrapers or brushes when cleaning tiled surfaces.
If dirt appears in hard-to-reach places, corners, then in this case you need to use flexible brushes for washing dishes with a long handle.
For cleaning the tiles on the ceiling, it is better to use dense gel formulations. They will not run down the walls and drip onto the floor. They are easy to apply and maintain for the required amount of time.
After using any detergent, rinse the tiles several times with clean water. So that there are no divorces left.
Steam cleaners are good for tiled surfaces. In addition to their cleaning functions, they have disinfecting properties.

When asked how to clean ceramic tiles from plaque in the bathroom at home, some housewives have an exact answer: a melamine sponge. When water gets on it, a lot of foam is formed. It copes well with all kinds of dirt without the use of cleaning agents. Many people confirm the quality of melamine sponges. However, some have concerns about leaving scratches on delicate tile surfaces after use.

Interesting! How to quickly wash a shower stall from limescale

Special means

You can use special products to clean tiles and joints. Most Popular:

HG. It is used to remove dirt on the seams of any color, as it does not contain bleach. The product is mixed with water in the proportion specified in the instructions, applied to dirt. The effect can be seen within 10 minutes, the remnants of the product are washed off with water.
BOZO. Removes any dirt: limescale, rust, dark spots, mold. It also removes odors and disinfects.Depending on the complexity and age of the contamination, the seams are treated with a product in the form of a concentrate or its aqueous solution.
"Atlas Dolphin". The agent is presented in the form of an emulsion. In addition to the cleansing effect, after application it forms a thin protective film that prevents the penetration of bacteria.
Cleaning pen. Contains dye and antiseptic components. It does not clean as much as it masks seam defects. As a temporary option, it is quite suitable.
Mellerud. Used for cured grout in bathrooms and kitchens, floors and walls. The product is diluted or applied in a concentrated form.

What methods are used for cleaning and bleaching of seams

There are several ways to bleach and clean an old grout, we will dwell on the main ones and tell you in more detail:

Pemolux for whitening

Cleaning using household chemicals. Treatment of seams with conventional detergents may not give the desired result, since they are designed to clean the smooth surface of tiles, while the seams are porous in structure, which significantly complicates the process of their processing. Therefore, in order to properly clean the inter-tile grout, it is necessary to use sufficiently strong acid-based products. But even the use of such strong preparations will only slightly lighten the old grout, for bleaching the seams, Pemolux has proven itself well. The drug is applied to the area of contamination and after some exposure it should be washed with warm water, to enhance the effect, you can use a hard brush, rubbing the composition into the grout. Remember to wear rubber gloves when handling strong chemicals.

Household cleaning of contaminated grout. The worst result of cleaning the seams in the bathroom can be obtained using at home, the means and compositions that we have at hand. For example, a mixture of baking soda and hydrogen peroxide will help bleach the grout. The composition is evenly distributed over the contaminated area, time is given to introduce the mixture into the grout structure, then, using a brush and an additional portion of the preparation, the joint is processed. After that, the surface must be thoroughly washed with warm water. You can also clean and bleach the seams with a mixture of baking soda and an acid, such as citric acid.
Mechanical cleaning. When it was not possible to clean the seam using one of the methods presented, this radical method will help to return the grout to its previous state. Using a scraper, a small semicircular chisel or sandpaper, the top, most contaminated layer of grout is removed. All work is carried out exclusively by hand, without the use of power tools and other devices, as this can damage the adjacent tiles.

For whitening, gels and powders are suitable for cleaning the surface of a gas stove or enamel

In cases where the dirt has deeply eaten into the grout structure, or it is severely affected by mold, which is almost impossible to remove, it remains to completely replace the jointing. To do this, all the old jointing is removed with a special scraper with a scraper, the resulting space is treated with compounds with antiseptics and a new grout is performed using the methods known to us. This work, of course, is laborious and painstaking, entirely consisting of manual labor. But the result will delight you with a brand new grout and shining tiles.

It is also possible to clean and bleach the seams between the tiles using technical means. Cleaning is carried out with a steam generator, in this case the joints are exposed to hot steam under high pressure, the dirt contained in them softens and leaves the grout. After that, the surface is washed and wiped dry. To protect the seams from mold and fungus infection, they can be additionally treated with antiseptic compounds.

Cement-based grouting compounds protect the space between tiles from debris and dust

If you do not have a steam generator on your farm, and you want to clean the tile lining in the bathroom in this way, due to its environmental friendliness and effectiveness, then you can use the help of cleaning agencies, whose list of services includes this work. In addition, professionals will be able to clean the seams better and faster.

There is probably the easiest and fastest method to whiten old grout, this is the use of a special waterproof marker of the required color. The coloring composition of the marker contains fungicide substances that prevent the development of fungus and mold. The protective layer that forms when the marker is applied has good waterproof properties, which makes it possible to use the marker in damp bathroom conditions.

Using a tile grout marker

Also, to give a whitening effect, a grout that has lost its appearance can be painted with water-based paint, applying it to the seam in several layers.

Radical methods

In especially difficult cases, when the defeat of tile joints by mold or fungus has gone so far that neither professional nor folk remedies help, there are only two options:

Completely remove the old tiles, treat the surfaces with antifungal agents and lay new tiles in compliance with all technologies;
Remove all grout from infected joints, treat with an anti-fungus agent, rub in with fresh grout, cover with a protective layer to prevent re-infestation.

Both in the first and in the second case, it makes sense to use the services of professional tilers. The pleasure is not cheap, but the result is guaranteed. The main thing is to control the removal of the glue so that you do not suffer later, how to remove the old tile glue from the tile.

If this is not possible, and only the second option is available for independent execution, we recommend taking into account the following tips:

Use a scraper, paint knife, chisel or power tool - drill, screwdriver, electric grinder, grinder.
Safety rules are above all! Only wear protective goggles and a mask when working with a power tool.
A weak vinegar solution is suitable for softening the grout.

Replacing grout

Since it is far from possible in all cases to completely wash the seams between the tiles, sometimes the most rational solution is to replace the grout.

Replacement is carried out in several stages:

With a scraper or any convenient tool.
Clean out any mold and mildew from the joints.
Treat the seams with a special treatment to keep your bathroom clean and hygienic.
After the antiseptic is completely dry, start applying a new layer. The best way to do this is to use epoxy grout mixes between tiles.
Using a rubber trowel, spread the mastic evenly over the seams and level them, remove the excess.
After the material has dried, wipe off any excess with a damp sponge and polish the tiles to a shine.

Tiles are one of the most popular types of finishing materials, they are often used in the decoration of residential and public spaces. Its material is practical, durable, high quality and easy to clean.

But, unfortunately, the tile also has weak points that you need to pay attention to and, if necessary, eliminate. We are talking about the seams that form during tiling.

Moisture and dirt get into them, in some cases mold and mildew appear. This article will focus on ways to eliminate such unpleasant phenomena, and how to bleach darkened joints between tiles.

Effective ways to clean tile joints

There are many ways to remove dirt, mold and mildew from seams. These methods include: purchased chemical agents
(various gels, powders, etc.), improvised means
(soda, hydrogen peroxide) and special household steam cleaners.

How to clean the seams with improvised means? You can mix hydrogen peroxide and water in a 1: 2 ratio and wipe the joints between the tiles with the resulting composition. In this case, the composition does not need to be washed off. Alternatively, you can mix water and vinegar in equal proportions, spray all the seams and clean them with a stiff non-metallic brush (for example, an old toothbrush). Unfortunately, you cannot achieve perfect whitening in this way, but it will definitely brighten the surface noticeably.

They also bleach the seams, clean them of dirt and disinfect them using purchased chemicals
... They are applied to the seams and left for a while for the cleaning agent to interact with the surface. Then wipe the seams with a wet cloth or rinse off the cleaning products with water. Be sure to use rubber gloves during work, since many cleaning products can have a negative effect on the skin of the hands.

However, it is best to use a steam cleaner to combat mold, mildew and various microorganisms. It will not only help to disinfect the surface, but also perfectly cope with various kinds of darkening and dirt on the seams between the tiles. The principle of operation of this device is based on the evaporation of water and the supply of steam under pressure to the surface to be treated.

To prevent the appearance of mold and mildew, the seams should be treated from time to time. antiseptic impregnation
.

In the case when none of the methods helped in solving the task, there is a more radical, but guaranteed way - this is a complete replacement of grouting. To do this, you need a scraper to remove the old grout.

All mold and dirt are removed from the joints of the tiles. Apply an antiseptic to the seams and allow time for it to dry completely. After that, you can use a special grout, which is evenly distributed along the seams with a rubber spatula, removing its excess.

After drying, remove any excess with a damp cloth and rub the tile until it is shiny. In this case, you will be satisfied and will not recognize your old (and now completely new) tiles.

After the appearance of mold, mildew and the appearance of dirt on the tiles, it is recommended to immediately start cleaning them. Indeed, over time, they will eat into the interior more strongly, and then it is much more difficult to wash them. But cleaning can be done in various ways: by folk methods, by using chemicals, bleach, markers and even steam. This is what we will talk about in more detail later.

A radical solution to the issue, or if the mold has penetrated too deeply

When mold penetrates the structure of the material, it is difficult to completely remove it. In these cases, chemical-based products become ineffective. A more radical mechanical method is recommended:

prepare a scraper;
to facilitate the process, the seams are treated with a vinegar solution;
the joint space is freed from grouting, but the tile adhesive does not need to be touched;
remove dust and debris from the surface, which will improve adhesion;
the seams are treated with antifungal agents, and it is important to follow the instructions, otherwise the quality of the adhesion of the materials will decrease;
a new grout is applied.

Folk remedies

Home remedies can help restore cleanliness and freshness to the bathroom. They are efficient, affordable and safe.

Baking soda

Baking soda will help to wipe off the tile joints:

Dampen the grout with warm water.
Apply a generous layer of baking soda, leave for 10-15 minutes.
Use an old toothbrush to carefully brush all joints until you achieve the desired cleanliness.
Using a large brush, apply some baking soda and scrub the entire surface of the tile to remove plaque, mildew and makeup.
Wash the tiles with water.

Baking soda, water and an old toothbrush will help you quickly, effectively and safely clean tile joints.

Hydrogen peroxide

A pharmacy can restore the whiteness of the seams. To prepare the solution, take water and hydrogen peroxide in a 2: 1 ratio. Treat the seams with the resulting product. The advantages of this method are efficiency, safety, no need to rinse the solution off the tile.

Vinegar + soda

Table vinegar is an effective remedy in the fight against mold, and in combination with soda, it effectively copes with other contaminants.

Step-by-step cleaning instructions:

Combine baking soda and vinegar in equal proportions.
Apply the mixture to the joints, leave for 10 minutes.
Clean the seams thoroughly with an old toothbrush.
Rinse off any remaining cleaning agent with water, wipe the tile dry.

Bleaching powder

In case of serious pollution, bleach comes to the rescue. It effectively removes dirt, disinfects, and makes the tile shiny. However, when working with the substance, observe safety measures: put on gloves, a mask, turn on the hood.

Cleaning procedure:

Dissolve bleach in water until a homogeneous liquid consistency is obtained.
Apply the solution to the surface using a spray bottle.
Leave it on for 5-7 minutes and then wash the tiles well.

After cleaning the joints and tiles, be sure to wipe the surface with a dry cloth. This will make the tiles shiny and will also prevent limescale deposits.

Vinegar and lemon

A solution based on soda, vinegar and citric acid will help bleach the grout between the tiles. To prepare it, prepare the following components:

1 glass of water;
250 ml of 9% vinegar;
6 tbsp. l. soda;
1 tbsp. l. citric acid.

Mix all ingredients until smooth. Using a sponge or stiff brush apply the solution to the seams... Re-treat after 20 minutes to ensure that the dirt is removed. After cleaning, rinse the tiles with clean water.

Peculiarities

Tile is an excellent finishing material that is durable and easy to maintain. However, rarely does anyone manage to avoid darkening, against which the usual wet cleaning is powerless. The messy look of tile joints that were recently white will upset any hostess.

Before we move on to studying how to clean the seams, let's figure out why the tile joints darken. The level of contamination depends on the purpose of the room in which the tiles were laid. Often, in the corridor and in the kitchen, the coating quickly loses its appearance, because these rooms are more polluted than others. The tile itself is washed regularly, but it is much more difficult to clean the seams, so this space is not often cleaned. The way to combat darkening must be selected depending on the type of pollution. Leftovers of food and detergents, dust, street dirt lead to them.