Shovel mount

Method 4: Suspend the bike using the bike handlebar

1. You can use an old steering wheel with the handles down to make a hanger with your own hands. The curvature of this handlebar will allow you to hold your bike securely. You can find a handlebar with the grips down at your local bike store or used one.

2. Attach the specially designed mounts to the handlebars and turn them upside down.

As an attachment, you can use the stem, which will hold the handlebars with handles. Old style stems are found on older bicycles and can often be found with a handlebar. They fit into the handlebar hole in the frame and resemble an "L" -shaped tube, with a handlebar clip.

3. Buy or find a threaded steel tube and wall flange that fits the stem. This tube should match the stem diameter so that you can slide the tube into the mounting hole without too much effort, the flange itself is attached to the wall.

4. Screw the steel tube into the flange. One side should hold the stem securely, and the other side should be screwed into the flange and tightened tight. You may need to adjust the stem to keep the handlebars straight.

5.Attach the flange to the wall. Find a timber frame post. Use a screwdriver to attach a flange that already has a handlebar and stem.

Types of trunks and features of their design

The trunk is a transverse strip that is fixed to the roof of the car. These products are classified into several types depending on the design features and types of fastening.

When choosing, you need to pay attention to the credibility of the manufacturer, the presence of positive reviews and the correspondence of the system for fixing to a specific car. The numerous advantages of a car roof rack have made this structural element one of the most sought-after

Open type

A universal product that can be installed on any car model. Such a rack is designed to transport various items. Due to metal crossbars and crossbars, the load is securely fixed and held on the roof. Additional fasteners guarantee stability and increased fixing strength. A distinctive feature of the device is its affordable cost.

The disadvantages of attaching an open roof rack include poor aerodynamic qualities, which negatively affects fuel consumption, and the lack of protection of the transported cargo from atmospheric precipitation. The reliability of the load securing is increased by the use of a net for securing the load on the trunk.

Car luggage box

Performed in two variations: hard and soft. Such a device protects the roof and transported items from precipitation and dirt. The rigid structure of the trunk looks like a box made of plastic or carbon fiber. The latter option is more durable, but its cost is higher. Products differ in volume, material and fastening system. When choosing, you must focus on the desired result and technical characteristics.

Trunk locks protect transported items from intruders, even in an unguarded parking lot. When driving, excellent aerodynamic qualities are provided, which reduces drag during high-speed driving and reduces the load on the engine. The average cost is 10,000 rubles.

Specialized roof racks

The rack is designed to transport sports equipment and bicycles.The system consists of a combination of fasteners. The product is suitable for people who lead an active lifestyle and prefer cycling in nature. The advantage of such a rack is mobility, because it can be fixed immediately before use, and then safely dismantled.

The disadvantages include an insignificant level of practicality, since the user has the opportunity to transport only a certain type of product (bicycles, boats, sports equipment). Despite the simplicity of the design, sometimes difficulties arise with its installation.

Universal trunk

This type of roof rack combines the features of the other varieties. It is suitable for fixing objects of various sizes, it is easy to install and dismantle if necessary. The versatile product is one of the most popular in view of its mobility and practicality.

Expedition rack type basket

It looks like a basket with special zones. Here you can place various items, for example, a bump stop, a spare tire, a flashlight, tools. This is a great option for hikers, hunters and fishermen. In addition, the product protects the upper body of the car from mechanical damage during driving. The expedition-type trunk mount has a number of distinctive nuances and features.

How to make a DIY wall mount shelf?

To make a shelf mount, you will need:

wide board made of natural wood or plywood sheet 1 sq. m, the recommended thickness is 1.5 cm.

It is better not to use MDF or chipboard, because over time such a shelf can break out of the mountings; glue for wood; wood stain and varnish for wood (optional); fastening bolts with washers with which the shelf will be attached to the wall.

To determine the required dimensions for your future shelf, measure three parameters:

Draw a drawing of the main parts depending on the dimensions.

Saw the board in accordance with the drawing and make a "rough" version of the box (but do not connect the parts together!).

Draw and then saw out a cutout for the top tube. It is better to do this with special equipment.

Now it's time to assemble the shelf.

Place all the pieces on the glue. Before using the glue, clean the surfaces from dust and degrease them. It is better to remove the remnants of glue immediately, so that in the future it does not interfere with the painting.

The top panel can be hinged to create a drawer, or simply attached to the base to create a shelf.

Drill holes for the fastening bolts.

Now you can safely hang the shelf on the wall, or you can take the next step - sand all the surfaces of the shelf, paint them with a stain (you can use two colors) and varnish.

An option for making a simpler shelf can be viewed here:

A wall mount for a bike will be an excellent solution for "parking" a bike in a small apartment. Moreover, this is not only an option for long-term storage (for example, in winter), but also for daily use, because the bike is so easy to remove and lift up again. What type of attachment to use is up to the rider himself, depending on the free space and his physical capabilities.

Wall Mount Materials

The stones need to be found oblong, about 15 centimeters long.

The width is not less than 5 cm, so that the wheels of the bicycle do not slip off them. We take a victorious drill, which is used to drill into concrete. Equal in diameter to right angle anchors. We drill two holes from the bottom of each stone.

If the side of the stones does not fit snugly against the wall, you can level that side with an angle grinder. Natural stones are easily processed with concrete discs. Then we thoroughly wash and clean the stones, they will serve as a decorative element on the wall and at the same time as stands for bicycle wheels.

Do-it-yourself mount

It is not difficult to make a wall holder for a bicycle with your own hands. You need to be smart and spend very little time.

This solution allows you to make a unique, exclusive accessory. You will need to purchase wide plywood 15 mm thick, one square meter, wood glue, varnish, and fasteners. To make a bike mount with your own hands, you need to take the following measurements:

It is necessary to make drawings of all the details. This will allow you to avoid erroneous manufacturing actions in the future.

The plywood must be cut as shown in the drawing. After that, you should collect the "draft" box. In no case should you connect them.

Draw pipe cutouts on the sides. Here you need to be extremely careful in order to avoid oversights. Then the finished parts need to be glued together.

Before this work, remove any dirt and degrease the surface. Remains of glue are removed immediately. The top panel is hinged.

Then you get a box. If this is done at the base, then there will be a shelf. Holes are cut out for fasteners.

The product is ready. It remains to give a presentable look. Here you need to connect your imagination and imagination.

It is not at all difficult to choose a bicycle mount, make it with your own hands.

You need to initially determine for yourself the criteria that are the most important and essential. Modern opportunities allow you to implement absolutely any ideas. Fastening the bike to the wall, ceiling will allow you to securely fix the vehicle, as well as provide high-quality and safe conditions for its storage.

How to make and install a shovel mount with your own hands

Shovel mounts can be created in several ways.

The simplest manufacturing option is from rubber elements: old insulating tubes, harnesses. But such fasteners earned a lot of negative reviews, because some fishermen and hunters lost an expensive shovel, securing it in this way.

A more secure attachment can be made with scaffold clamps or swivel clamps. It is necessary to separate them using a hacksaw for metal or a grinder, make a hole with a diameter slightly larger than the diameter of the bolt for fastening, replace the nut with a winged nut. Scaffolding clamps hold the tool firmly, but are difficult to make holders with. In addition, this requires some inventory.

The lamb tends to unwind while driving due to vibration.

A quality grip is made from conventional plumbing clamps. You just need to replace the nuts with the wing nuts. The mounting hole looks pretty decent. Rubber, which is used as a seal, is another plus in favor of such clamps. They make some of the most reliable, simple and cheapest holders.

Thus, fasteners can be made from:

• rubber elements;
• clamps for scaffolding;
• swivel clamps;
• plumbing clamps.

If the options for self-production are not suitable, in order to choose a suitable ready-made fastener, it is worth watching the video:

Previous post Fastening floor mats in the car
The next entry Features of formwork for strip foundations and in-situ concrete

The height at which the bike will hang

After that, the height of the attachment is determined. To determine it, it is advisable to ask the person to hold the bike at the time of measuring the height. It is advisable to try it on at different heights in order to determine which one is the most suitable (whether it will interfere with the passage, annoy with a too low position, or will it fit ergonomically into the interior of the room).

Setting it too low can be annoying that the handlebars or pedals of the bike will make it difficult to pass smoothly underneath.But too high a position is unsafe in case of poor health, frequent dizziness when looking up, or weakness of a person. Therefore, the most optimal type of ceiling mount for such people will only be the use of a bicycle lift.

Selection and installation of bike hooks

The easiest and cheapest way to secure your bike is to use bike hooks, which are divided into two large groups:

The wall mount for the bike in the form of hooks for horizontal storage can be one of the following types:

Individual wall-mounted hooks

Mounting in the form of hooks mounted on the frame

Vertical hanging hooks:

Bicycle suspension device from the ceiling

Vertical suspension device

Mounting hooks is straightforward. To install you need:

Drilling holes for attaching hooks

Preparing to attach the hook

How to make hooks for hanging a bicycle to the wall with your own hands, look at the video.

Material preparation

All the necessary material is prepared for creating a rack, according to the prepared project:

• For the main panel of the holder, you can use a perforated panel.
• If the rack is made of wood, it is recommended to purchase oak or pine lumber without cracks or knots.
• Wooden boards up to 2.5 cm thick are required for the shelves.
• Shelves can be made of plywood and laminated plywood.
• The vertical racks of the frame are made of a 10 × 10 cm bar.
• It is recommended to pre-treat wooden boards with anti-mold and mildew agents, paint.
• To assemble a metal frame, a rectangular profile and corners (up to 2 cm) are required.

Manufacturing of components

The procedure for manufacturing the rack and accessories is as follows:

1. According to the specified dimensions, vertical racks from a bar and boards or plywood are cut into shelves, a perforated panel is prepared. Outline shelf spaces.
2. For the manufacture of a metal frame, workpieces of the required height are cut with a grinder and the locations of the shelves are outlined. The frame is assembled with fasteners, corners. Apply a primer, then cover the parts with anti-corrosion paint.
3. Shelves are assembled from boards. They are pressed tightly against each other and hammered together with nails or self-tapping screws.
4. Shelves from boards are assembled by laying the elements across the frame, so they can withstand a lot of weight. If the shelves are assembled by laying the boards along the frame, then there is a possibility that they will sag under the weight of the tools.
5. The structure is assembled with self-tapping screws, nails and wood glue.
6. The joints of all parts are additionally reinforced with metal corners.
7. The entire structure is mounted to the wall and secured with metal brackets.
8. Shelves with saws, holders, magnetic tapes, racks, containers and organizers are manufactured separately in the required quantity.
9. You may need a small work table with a wood plank vise. It can be attached to the wall system as a stationary or flip-up surface using metal or wooden holders.

Types of fasteners

There are several types of fasteners. And they differ in the time it takes to retrieve the tool and in the reliability. But if the shovel is not attached from the outside, the choice between them does not matter in principle.

Single track

Single-track holder types consist of a base and a hook that is attached to the base. It closes with a bolt and nut. The nut can be made in the form of a wing. The opening of the single-arm holder is faster than the double-arm. Sometimes the shovel is secured with a slotted prong.

Double-horned

This type of fastener is suitable if the tool is not used frequently and is only used for a shovel.

It holds in most cases better than a single-lug one, consists of a base and a clamp, which is attached to the frame at both ends using bolts or "thumbs".It's easier to make it yourself.

Installation rules

Before installation, you need to think about where and how the holder will be installed, so that later you do not have to redo the fasteners

Slightly less important, vertically or horizontally, it will be fixed. They are usually installed horizontally in a car.

It is worth checking how convenient it will be to use it.

Wall mounting

First you need to choose a location. Indoors, it is best to place the fasteners horizontally at about 190 cm above the floor in order to take up a minimum of free space on the wall. Outside, it is advisable to install the fasteners so that the metal elements of the structure are not flooded with rain, otherwise corrosion is possible and you will have to change the bolts of the fasteners.

You can attach a shovel to any suitable, preferably wooden, plane, for example, a canopy post, garage wall, door, but first of all, you need to evaluate the convenience.

Installation on a car and other equipment

The shovel can be attached to the outside or inside of the vehicle. In the absence of roof rails or other means of fastening on the roof of the car, it remains to mount the shovel in the luggage compartment. And it is not at all necessary to keep a full-size shovel in transport. A sapper shovel will always help, although not as effectively as a full-size one, to remove dirt from under the wheels. It can be attached to the ATV when going on a long hike.

You can attach the holders to the rails with bolts and washers. If the fasteners are located in the trunk, you should be prepared for possible damage to the plastic in the trunk.

Gadgets

All fasteners for shovels can be roughly divided into two groups:

• wall-mounted;
• floor.

Varieties of wall mounts.

• Hooks. They can be different both in shape and length. Hooks are usually attached directly to a wall or to a metal bar. They can be arranged in rows or in a chaotic manner if the blades and cuttings of shovels are of different sizes. The hooks are positioned sideways to hold the cuttings. The vertical position of the hook is intended for tools with holes (for convenience, you can insert a cord into them and hang from it).
• Hangers or brackets are usually designed for larger instruments, with twin mounts. Their length reaches up to 30 cm. But one pair can fix several shovels at once. Moreover, the heaviest ones are better placed closer to the wall, and the lighter ones - at the edge.
• Holders - are complex systems with fasteners in the form of protrusions or rings. In them, tools can be placed both horizontally and vertically. The attachment of the shovel will be more reliable if it is fixed in several places, and not in one.

All of the above mounts can be found in stores with inventory or you can build them yourself. The easiest option is to buy suitable hooks (prefer metal ones). If desired, they can be welded to the metal base. The next way is to make cuts in the board. It is better if it is fixed at an angle to the wall so that the shovels do not slip.

Floor mounts for storing shovels.

• Corner.
• Mobile. More profitable is this option, which can be installed along the wall or in any other more convenient place. Or, even better, take it with you to your work site to avoid throwing your shovel on the floor or the ground.

Any of the proposed options can be made by yourself: a stand from a box or a holder from a suitable pipe. The temporary option can be quite simple, you just need to take care of stability and convenience.

There are also more massive storage racks or cabinets. As a rule, they are universal or designed for a specific group of instruments. Thus, it is possible to re-equip a regular cabinet or pencil case using the ideas of the fixings mentioned above.

Transport fasteners

Shovels are often taken by themselves.But sometimes even a small, portable model barely fits in the trunk. And a large shovel will have to be placed in the cabin. This option is unsafe for the driver, leaves little room for passengers and can damage the passenger compartment. If the car is equipped with an expeditionary rack, the solution is simple: you need to place a shovel on it. And special mounts will help with this. You can find many models:

• made of metal;
• plastic;
• rubber;
• polyurethane.

Each has its own pros and cons. Metal ones have good strength indicators, but they are inconvenient to use in cold weather. Plastic is less durable. Rubber fixes better, is easily adjustable, but again, does not withstand strong temperature changes, it can burst. The most popular model is polyurethane. In terms of its properties, it is much superior to others. This is confirmed by numerous reviews of reliability and long-term use in various weather conditions.

In addition to the material, such fasteners differ:

• by the diameter of the handle (they, in addition to shovels, can be used to attach fishing rods, pipes, hoses - they will definitely come in handy on the farm);
• according to the maximum load (depending on the weight of the tool being fixed).

Two attachments are required to secure the shovel. Their cost varies from 300 to 1000 rubles apiece. There are dual mounts on sale, for example, for a shovel and an ax. Or wider, allowing you to fix two shovels at the same time.

Other options for storing shovels are described in detail in the video below.

Maybe in the room?

If it is not possible to install a bicycle in the hallway, basement, you can store it in the living room. A simple way is to hide it behind a screen.

You can easily choose a mounting model that matches other interior elements, which will be an interesting addition. It is enough to purchase a spectacular bracket, a suitable platform, lay a simple rug, thanks to which we will effectively protect the floor from possible damage and dirt.

The bicycle should not be viewed as an element that reduces the floor space of the apartment.

You can make it a decorative element. It should not interfere with daily activities. Ideal for:

Then he does not bother us, while at the same time acting as an interesting addition to the interior. The solution is ideal for cycling enthusiasts who love to contemplate their two-wheeled friend.

Conclusion

Setting up a small apartment requires a lot of creativity, especially for cycling enthusiasts who have to look for additional storage space for cycling equipment. Lack of storage space should not be a reason for refusing to go for walks or sports.

There are many ways to incorporate your bike into your home without interfering with your daily life. How to do this so that the apartment does not turn into a garage? It takes a little ingenuity, some space, so we can store our equipment seamlessly during and after the bike season.

If it is not possible to find a place for a classic bike, you can look towards the folding model. Once folded, it is small enough to fit under a table, in a closet

The advantage of folding models is low weight (important if you have to lift up the stairs), the disadvantage is the price (if we are looking for a safe model with a really strong structure)

Although the dimensions of the bike are quite significant, this does not mean that it is impossible to store it in an apartment. Modern technical solutions come to the rescue:

In addition to the traditional holders that immobilize the bicycle wheel in a special rail, there are versions mounted on:

They allow equipment to be placed in different positions using the available space.

other methods

Other storage methods include:

Cupboard. Ideal for storing multiple units, pumps and cycling accessories.Essential for a large family with several cycling enthusiasts.

Both adults and children are accommodated. The wardrobe can be placed on a heated balcony or in a spacious hallway. Negative - takes up a lot of space. Rear wheel stand.

A huge plus - takes up little space and securely fixes the bike. But high-quality metal stands are expensive, and plastic ones can break quickly. This storage method is borrowed from the Scandinavian countries.

How to make a trunk with your own hands

The cost of roof racks is high. In addition, the quality of products does not always allow transporting too heavy loads. That is why the independent manufacture of the structure would be an excellent solution. This will require tools, materials, some skills. The most common and practical are expeditionary and universal roof racks. Their advantage lies in the ease of repair and maintenance.

When creating a trunk with your own hands, it is necessary to take into account that the system must have high strength and reliability, since the safety of all road users directly depends on this. In the event of any accident, the driver of the vehicle is solely responsible.

Most car enthusiasts use this component only when needed. In this case, it is advisable to make the system removable. A master without special skills is recommended to start by creating the most common variety - a universal one. The main feature is the presence of two crossbars. For self-production, you will need the following materials and tools:

• grinder;
• dye;
• fiberglass with a density of at least 300 g / m²;
• polyurethane foam;
• clamps - 4 pcs.;
• aluminum profile 20 × 30, its wall thickness should not be less than 1.5 mm.

Any metal can act as a material for the profile, but aluminum products have high strength characteristics and, at the same time, have a small mass. For the manufacture of a high-quality roof rack and its attachment to the roof, you should adhere to the established algorithm of actions:

It is necessary to cut the cross members, the length of each must correspond to the width of the car body part.
Products are covered with foam on the inside and outside. A dense layer will allow at the third stage to give the necessary configuration to the crossbars.
When the foam hardens, the excess parts are removed, and the surface is processed with a grinder. The profile must first have the shape of a parallelepiped, then adjustments are made to obtain good aerodynamic properties - you need to grind off the corners.
Due to the porous structure of the foam, the material is exposed to negative environmental influences. The substance tolerates contact with moisture especially poorly. Automotive putty is used to provide a high level of protection.
Then the crossbars are wrapped with three layers of fiberglass.
Then paint is applied.
While the structure is drying, you can proceed to the manufacture of fasteners. Clamps are the simplest and most economical option.

It is important to file the bottom of the product so that the plate is flat. This is necessary for tight and reliable contact.
Two holes are drilled in the crossbars from each edge

Such a distance must be maintained between them so that the ears of the clamp enter.
At the final stage, the cross members are attached to the rails. To avoid damage to the cross member with clamps, rubber gaskets are placed in the contact points.

This is the simplest technology to create a roof rack for a vehicle. Its advantages include high speed of implementation, cost-effectiveness, reliability and quality. However, the service life of a structure is limited by various factors, including the amount of precipitation, the size and weight of the cargo, and the distance of transportation.If the car is not equipped with rails, then you will have to think about another method of securing. It is not difficult to install such a roof rack, the main thing is to understand its design features.

Building an expedition rack takes more time, money and skills. You must first draw up a detailed drawing and acquire a welding machine.

Smallest holder

An apartment decorated in a minimalist style is too large objects, hooks will not decorate. There is a compact solution - the smallest screw holder only takes a few centimeters. U-shaped fasteners, made of durable material, available in many colors.

The holder looks interesting, modern, you can choose an option for different sizes - it works for several wheel sizes.

The fixture is wonderful, simple - one small bracket is enough to mount the bike vertically. You just need to "shove" the front wheel into the fastener, and the bike stands against the wall. The holder can also be fixed to the floor.

Features of storing shovels

In addition to searching costs, proper storage of tools affects tool life. Each material requires its own conditions. For example, moisture will seriously damage a wooden handle. Plastic, if handled carelessly, can break, and the metal blade for digging can become dull or get jagged

It should be borne in mind that an inventory thrown in a chaotic manner can cause injury. Therefore, all kinds of fasteners and devices for their placement are used.

The placement of shovels should be appropriate:

• in a dry room;
• away from the aisles;
• using attachments that are comfortable, safe and fit at the correct height so that the instrument can be easily picked up and returned.

Racks or stands

Stands or racks are an interesting, non-standard solution. The service stand allows you to hide your bike in a hard-to-reach place.

The option is suitable for people who independently take care of the repair of their own two wheels. The device allows you to comfortably repair breakdowns. The stand is ideal for service work:

You can pedal freely on the stand, so it is easy to adjust the rear, front derailleur, set the brake.

The strut hooks should be covered with rubber protectors to avoid the risk of scratching the frame.

The stand can have an adjustable height, tilt angle. The adjustable height up to 145 cm and the 360-degree range of frame installation make it an indispensable tool for repairs and adjustments.

Convenient place in the closet

This is a suitable solution for families where more than one person uses bicycles.

It is worth considering the installation of a small built-in wardrobe in the hallway. Bicycle equipment can be hidden in the closet. Bicycles are placed in several ways:

Thanks to this, they take up less space, you can put several pieces side by side. This solution is rather complicated, but it provides the best conditions - the walls do not get dirty, the placement is quick and easy.

In the economical, less advanced version, it is enough to install the mount on the door in the apartment. You can use an existing niche - under the stairs, in the hallway, or create an additional "wall" from the wardrobe. Sliding doors are easy to install and we can adapt their size and color to the interior.

This is a fun way to use small free space that we didn't know about until now. Bicycles are hung vertically, just like in built-in wardrobes. You don't need a lot of space to safely store your equipment.