How to fix a button on jeans: repair and replacement rules, installation methods

Restoration of denim buttons. | club-snap.su

Nothing lasts forever under the moon, including denim buttons. The button itself is safe and sound, but the attachment point has come apart or the fastening stud has broken off, and the button has fallen out. It's good that I didn't get lost. Let's help your favorite denim button to return to its place. Option A: Denim button on a stable cast metal leg. The base of the denim stud has broken off.

We clamp the button with pliers and carefully drill out the remains of a denim nail with an electric drill. Drill Ø 2mm.

Result - removed the remnants of cloves

The denim button is ready to be reinstalled.

We do the same with a plastic button in a metal sheath with a broken fastener. The pin of the denim stud remains inside the button leg. We drill it with an electric drill. Result. If the inner hole turns out to be a little larger than a denim stud, don't worry. Using a toothpick or a match, fill the hole or use a piece from a Ø 9mm holniten. Then carefully install the button. - If a denim button just fell out due to the destruction of the fabric, and a denim stud remained inside the button, proceed as follows: A. Drill out an old denim stud. First, make a notch for the drill with a center punch. Clamp with pliers and carefully drill with an electric drill. Further, as described above, B. We take out the denim nail using two side cutters: One side cutter works as a support, the second as a lever Result Next: install as described above.

Attention: You should not use this method of removing a denim stud on buttons with a broken leg, get the following result: Buttons on a broken leg can only be restored with an electric drill. Next, install in the above described way. We also drill denim buttons made of cast metal with a through hole, and, depending on the diameter of the inner hole, install either on a holniten part or on a tubular denim-holniten stud. The fact is that during compression these parts increase in volume and firmly fix the denim button. Thin metal through-hole denim buttons are difficult to repair

It is necessary to drill a hole very carefully so as not to touch the walls of the button. Etc. Therefore, in most cases, it is easier to install a new button than to restore an old one. But if it becomes necessary to restore an old denim button, then you will successfully cope with this task. Unfortunately, mainly on sale side cutters are such side cutters, with a deep notch. You will have to remove excess metal on the grinding wheel and make the surface of the side cutter flat

Through hole denim buttons made of thin metal are difficult to repair. It is necessary to drill a hole very carefully so as not to touch the walls of the button. Etc. Therefore, in most cases, it is easier to install a new button than to restore an old one.

But if it becomes necessary to restore an old denim button, then you will successfully cope with this task. Unfortunately, mainly on sale side cutters are such side cutters, with a deep notch. You will have to remove excess metal on the grinding wheel and make the surface of the side cutter flat

- Often there is a need to rearrange denim buttons.

For example: in order to reduce the volume of the cuff of the jacket or increase (decrease) the volume of jeans in the belt. Carefully remove the button, being careful not to damage the fabric. If the denim carnation does not want to be pulled out, we bite it, then drill out the rest of the carnation. We punch a hole in the place of the marking, install the button. We close the place of the previous installation of the denim button with a matching cap of the color and size.

How to replace a button on jeans? Options. Ways. In detail. Photo

Good day, dear blog readers!

Despite the fact that the denim buttons themselves, and their attachment to the finished garment, are very durable, nevertheless sometimes such buttons "fail".

Most often this happens with buttons that are on the waist line and are subject to increased stress there.

For example, on jeans.

Denim buttons. Views.

How to put a button on jeans using special tools?

Installing a denim button using the tools at hand.

How to change a button on jeans?

1. The button is about to "break free with the meat" and fall off. And it also keeps, as they say, on parole.

2. From a button on a fixed leg, the interior of which is filled with shock-resistant plastic, a carnation fell out of its own accord from the "hard life".

3. One of the button spikes on the double stud has broken.

4. The main part of the floating leg of the denim button has come off the additional movable part.

Here are the main types of breakage that happen to denim buttons.

5. Yeah, here's another thing! By chance, in a fabric store, you caught the eye of the unearthly beauty of a denim button. And you immediately realized that her presence on your jeans will make them more fashionable, brighter and, in general, they will become like new. But, on jeans there is an old button and is clearly not going to "retire".

However, it doesn't matter. Knowing the rules for installing denim buttons described in several previous articles, jeans that have become unusable or unloved can be easily replaced with new ones.

I would like to remind you that the easiest way, manually, at home, is to install denim buttons with a fixed leg, on a stud with a circular notch.

Therefore, when choosing a new denim button, it would be good to take this into account.

Well, let's get down to business.

If the button does not fall out completely, and the parts that are firmly embedded in it remain in the material, then you can remove them with side cutters.

Farther. We look at the state of the hole for the button. If it is not very broken, then you can install a new button in the same place. You can read how to install a denim button on a double stud here. Read about installing other types of denim buttons here.

If the hole, as they say, is torn apart, the insides stick out from it, then you need to patch it up a little with threads that match the color. And the place for the button must be moved a little further, at least 5 mm towards the narrowing of the belt volume, and a new button must be installed (as in this or this article).

But, alas, in the overwhelming majority of cases, there is no way to transfer the button to another place, although it is located very close by. Pants and so back to back.

You can, of course, use a denim button with a stud in the form of a tube. Such carnations are somewhat wider than their counterparts, all-metal, smooth and notched.

And they should fit tightly into the hole on the product left over from the previous carnation.

But what about a situation when this kind of denim button could not be bought?

This means that the hole in the material needs to be properly sewn up, leaving, all the same, a small hole for a new stud.

And install a new button in the same place. But before that, from a piece of leather, plastic or some other dense material, cut the round pieces twice as wide as the head of the carnation and place it on the wrong side under the head of the carnation.

Thus, the head of the carnation will have additional areas to cling to the material more tightly.

Well, now, they learned to put jeans buttons at home, and to replace those that have fallen into disrepair.

I hope that a small series of articles on denim buttons will be useful for those who "surf" the "waves" of the Internet in search of just this information.

Do you know how to cover a button with fabric? No? Come read about it in the next article.

How to install a button on jeans?

The installation of each type of fasteners requires its own approach. However, there is a lot in common in the repair methods.

Use the following guidelines when attaching the fastener to the fabric:

It is very difficult to make a button on jeans if it has a convex or concave top. With the inevitable blows of a hammer on such a part, its shape may change, and not for the better. We recommend not buying such rivets at all or installing them in a special workshop.
Choose immediately a set consisting of a button and a stud for denim.
If the pin is longer than necessary, you can cut it off or bite it off with a side cutter or pliers. Or you can put a gasket under it from the seamy side.
Before attaching a button to the material, you need to decide and mark its future location.
Make punctures for studs with a punch, an awl, a thick needle so that the sharp ends of the stud do not tighten.
All types of hairpins are inserted into the notch from the wrong side of the fabric, and the button itself is adjusted from the front.
It is best to manually attach the rivet without a central notch and on a stud with a circular notch.

3 Rivet installation process

How to rivet material with your own hands? To do this, you need to work carefully, do not rush, do not make sudden movements. Otherwise, the tool, fabric material and sewing accessories may be damaged.

The most common type of hardware installation at home is the installation of a block. Ateliers and workshops have tongs for this purpose. The hallmark of good pliers is the strong, rigid handles that allow you to work quickly and smoothly.

Do not despair if special forceps are not at hand, you can do without them at home. How to make a mount yourself?

A hole of the required diameter is made in a textile or leather material using a punch. The block is threaded, then the ring is inserted. The place with the block is located on the anvil, then its leg is split with a punch. If all steps are performed correctly, the rivet petals will bend themselves properly. For the final fixing on the block, you need to walk with a hammer, without applying great force.

There is another way to install this type of rivet. The leg is cut with a knife and light hammer blows on it. This should not be done along the entire diameter, cutting is performed only in some areas of the petals, then insertion into the prepared hole is performed. A ring is put on the resulting structure, the bent petals are bent. In ateliers and workshops for sewing and repairing clothes, this method is not used, its use often entails damaged rivets and deformed areas of fabric.

Varieties

Clothing buttons differ in material of manufacture:

metal;
plastic.

> According to the method of attachment, they can be:

installation - fixed with special tools;
Sew-on - you need a thread and a needle to attach them.

Depending on the form, purpose and application, they are divided into:

simple;
s-shaped;
shirt;
magnetic;
glue;
holster;
strips;
tablet.

O-shaped

The most common type of buttons is O-shaped. They are called simple, ring, or flying, because the fastener first appeared on jackets and overalls for pilots.The design is straightforward and consists of two metal parts that fit tightly into one another. The upper component is spring-loaded.

Simple buttons are used on various types of casual wear as well as on specialized textiles.

S-shaped

This type is of the spring type. One of the parts resembles the letter "S", so they are called s-shaped. Depending on the size, they are divided into several types:

shaped - the size of the top is from 27 to 40 mm;
article - half the size of the uniform;
anorak - compact size;
mini anorak - the upper part is less than 8 mm.

The shape of the top is varied - from flat and round to diamond-shaped, square, drop-shaped. They are fixed with sewing or fasteners. The large spring can handle heavy loads.

Shirts

Shirt-type buttons differ from the usual way of fastening - not with a single pin, but thanks to 6-8 spikes. The design allows fastening fasteners on fabrics of low density. They are suitable for children's clothes, knitwear and knitted clothes, light summer jackets.

The devices are convenient to use, but quite expensive and expensive to manufacture. During installation, the material is pierced by spikes located on the ring. Their diameter ranges from 9.5 mm to 40 mm. The largest ones are used on jackets.

Magnetic

Self-closing fasteners with magnets are most often used in household products - bags, outerwear, wallets. It is convenient to use them, but they are expensive for production. The strength of the connection is high thanks to the magnet, and it is very easy to open it even with one hand. The magnetic button device includes four parts - two bases and the same number of mounting flanges. The magnet allows you to automatically select the position and close. The larger the size of the fastener, the greater the connection force.

Holster

This type has another name - tablet. They have been produced since the times of the USSR, when they were necessary for fastening military haberdashery. The lower part of the structure is very similar to the part of an s-shaped device. The top of the castle is hollow inside, petal-shaped. Its size is 12 mm. When the button is fastened, it expands and contracts. Most often, the buckles are nickel-plated, but they can have two more color variations - black and brown.

Clay or block

On the cover of a clamper or block button, the fastening is ring. This is the main distinguishing feature of the clasp. You can see the fasteners through the hole at the top. It is similar to its s-shaped counterpart, but is much larger in size. The most common fastener sizes are 8-21 mm.

How do I fix a button on my jeans?

Very often on jeans, rivets break on a broken rod. Under increased load, such products simply jump off the rod. This is their disadvantage. To replace the rivet, it is necessary to remove its remnants.

This can be done with a side cutter or pliers in one motion. And how to put a button rivet on jeans - you already know. Here are just a few tips:

If there is no damage to the fabric, then buy a new fastener, then insert the button leg into the recess, and attach the metal hat to it. Flip the jeans over and press the bonnet against a horizontal hard surface. Hit the rod with a hammer to secure it.
If the fabric is damaged at the location of the rivet, then first put on a denim patch, completely cover the damaged area. Sew the patch by hand or with a typewriter several times. Then install the rivet on the leg.

Instructions for replacing riveted buttons

If the button that has come off is not lost, it's already good, you can take it with you to the store to show it to the consultant and buy exactly the same one.If the button is lost, you need to measure the length and height of the buttonhole: such measurements will give you at least an approximate understanding of which button, what diameter and height you will need to acquire.

If the rivet button just flew off, without damaging the fabric of the jeans, and both parts of the button are available and not damaged, take the button leg, insert it into the button hole on the jeans waist (the place where it fell out). After that, you need to attach its metal hat to the leg of the button, then turn the jeans over, pressing the button hat to a horizontal hard surface, and hit the leg with a hammer, hammering it into the hat. The blow should be clearly directed, but not strong, so as not to deform or damage the button.

If the button flew off "with meat" and the fabric of the jeans belt itself is damaged, then first you need to put a patch "on the wound". Using a patch cut from a piece of denim (preferably the same as your jeans), completely cover the damaged section of the belt on both sides and sew several times on a typewriter or by hand. Then we do the manipulation with the installation of buttons-rivets on the leg on the belt.

In the event that you are unlucky with these metal buttons or you just don’t like them, you can try matching your jeans with a regular button. Correctly sewn, they hold for a rather long time, are easier to fasten and in case of an "accident" they are easy to replace. The only wish: be careful about the size when buying such a button - it must be exactly matched to the size of the buttonhole. Buttons that are too small will not keep the jeans buttoned up, especially if the model is not loose at the waist. A button that is too large will cause daily discomfort.

Rivets for clothes are an invisible, but irreplaceable element of every thing, from sheepskin coats, fur coats and jackets to underwear. Even expensive branded clothes are often equipped with low-quality fittings: clips, hooks, zippers. Very often decorative rivets come off, and an expensive item becomes unusable. In order not to seek help from a clothing repair shop, you need to learn how to work with a variety of sewing accessories on your own.

Patch

When the button falls out entirely, and a hole remains in its place, you need to make
patch. A circle with a smaller diameter than the width is cut from a dense piece of leather.
belts. In the middle of the leather patch, it is pierced with an awl or a thin nail
hole, a pin is threaded into it, on which a button is then placed.
At the same time, the patch remains on the inside of the belt. You can grab it
threads so that later it does not curl up. But this is optional.

Buttons on jeans are usually made in the form of a metal rivet. This, of course, protects such a button from a quick detachment, however, if such a rivet has come off, this sometimes constitutes a real problem. Not only can you not sew such a button with a needle and thread, but they often do not just come off, but literally "with meat", which, of course, also complicates the process of repairing a denim fastener.

Learn how to return the button to its place and repair the damage to your favorite trousers - in this article!

Additional tips and tricks

Fasteners with a broken rod are often damaged on these clothes. Such products are constantly exposed to high loads. As a result, they simply fly off the rod. This is considered their main disadvantage.

To change the rivet, first of all, you will have to get rid of its remnants. Carry out the procedure with a side cutter. It is also allowed to use pliers. It is recommended to remove leftovers in one motion. A new rivet can be fitted using standard technology.

In this case, it is worth following these recommendations:

If the fabric is not damaged, you can purchase new accessories, after which the button leg is placed in the recess, and the metal cap is attached from above. Then turn the clothes over and press the hat against the table. The surface must be flat and firm. After that, it is good to hit the rod with a hammer. This will help fix it.
If the fabric is damaged in the area of the rivet, it is recommended to make a patch first. It is made of denim to close the problem area well. The patch should be stitched manually or with a typewriter. Then it is recommended to install the rivet.

If the rivets do not hold well or are constantly lost, it is worth picking up an ordinary button. This should be done very carefully. The button must match the size of the buttonhole. Too small detail will not securely keep jeans buttoned, and too large will cause daily discomfort.

It is easy enough to fix a button on jeans. However, first of all, it is recommended to determine the type of fittings and choose the best option. After that, you need to choose the type of repair and strictly adhere to the required sequence of actions.

Share link:

How to restore a damaged

If the metal button has ceased to perform its function and is constantly unfastened, a regular hammer can help.

To do this, the convex part of the fastener is placed on a hard surface and carefully strikes, slightly flattening the "bump". After each hit, you must try to fasten

Once the fixation is secure, the goal is achieved.

The plastic fastener can be repaired with an iron, tracing paper, or foil. To do this, the convex part is covered with foil or tracing paper and slightly melted. After the plastic has hardened, they try to fasten it. You can touch up the melted edges of the button with a nail file.

1 Types of rivets and materials

There are two types of rivets: utilitarian (those that are used for clamps, fastening and fastening) and decorative. Sometimes sewing accessories in a product combine both roles.

It is important that it contributes to the comfortable wearing of things. Sticky zippers, detachable hooks and slippery buttons force you to throw expensive items into the farthest corners of your wardrobe

The first step that needs to be taken towards the correct selection of fittings is to learn to distinguish one type of it from another.

Types of fittings:

loops;
hooks;
buttons;
textile Velcro fasteners;
blocks;
lightning;
holniten (metal rivets, which are most often used in denim clothing to secure stitches);
eyelets (strong metal or plastic fasteners, which are most often used in leather goods);
buckles.

The materials from which the indicated types of fittings are made are very diverse. Their quality determines how comfortable and comfortable the wear of the thing will be. In addition, the accessories are designed not to disfigure, but to decorate the thing, even if we are talking about such an ordinary detail as rivets on clothes.

The most popular materials for making buttons, fasteners, fasteners are metal, ceramics and plastic. Most often, sewing accessories are made from a combination of materials in order to combine both practical and decorative characteristics in a single piece. If the part is incorrectly selected, the features of the fabric and leather are not taken into account, the fastening is incorrectly carried out, then the accessories simply will not cope with the functions assigned to it. After all, it is necessary not only to fasten the edges of the clothes with high quality, but also to decorate the thing harmoniously.

Installation and replacement methods

Jeans can be riveted in a variety of ways. With this in mind, select the type of fasteners. The repair of such elements is also different.

On a stable leg

It is easiest to replace such accessories. This type of repair can be easily done on your own. To carry out the procedure, it is recommended to perform the following steps:

To install a button, make a hole in the denim material. For this purpose, you can use an awl or a nail. A hand punch can also be used.
Place the fastening stud in the hole.
Drive the so-called button hat into it, like driving an ordinary nail. At the same time, you cannot put a lot of effort. Otherwise, the fittings will be damaged.

On a smooth nail made of solid metal, it is worth installing in the same way. But it is recommended to shorten the product first, since it is usually a little larger than necessary. As a result, this part protrudes above the fixed button.

Rivets

At home, it is easiest to install a flat button without a notch. It can have a pin with a circular cut. To carry out the procedure, it is worth performing the following actions:

Determine and mark the location of the clasp.
Pierce material in the installation area. It should be done with a nail. You can also use an awl. An equally convenient option would be a hand punch.
Place the nail in the hole. It is recommended to do this from the inside of the product.
Attach a button hat. It should be placed on a hairpin. It is recommended to do this from the front.
The button will fit correctly if the nail goes exactly vertically into the hole.
Press down the hat. The product must lie on a flat horizontal surface

It is important that the coating is as hard as possible.
Hit the hat. It needs to be done with a hammer

It should be hammered firmly into the clasp. It is recommended to ensure that the blow is clear and has the correct direction. However, it is not recommended to do this too much. Otherwise, there is a risk of damage to the product.

Buttons, which differ in a plastic base and do not contain a metal shell, should be installed very carefully. When driving a stud, it is recommended to keep an eye on the alignment. Otherwise, the hairpin will simply split. If you don't want to risk it, you should refuse to buy such accessories.

On a broken leg

You cannot sew on such a button. It is recommended to place it on a sturdy wooden surface. To do this, you should use an ordinary or tubular smooth carnation. When carrying out repairs, it is recommended to observe alignment. However, this is very problematic to do. Therefore, it is worth preparing the bolt and tube. Its length should be approximately 10 millimeters.

It is also permissible to use a socket wrench. It is recommended to hammer the rivet into the required place and carefully evaluate the quality of the installation. To do this, the product is pulled in different directions. After such manipulations, it should not pop out.

On a broken leg with a hole

Repair of such accessories has certain features. It should be installed on a solid metal nail. It is advisable to choose an aluminum product. It is permissible to use a tubular metal nail. The procedure is carried out on a flat and level surface. It is recommended to pierce the fabric with an awl and install a button. After that, hammer it on a nail. If it has a circular notch, it will be much easier to carry out the procedure.

Dual mount

The flat base of the fixation is considered a key characteristic. It should be pierced with 2 studs, which are pieces of hardware. After that, thorns protrude from the other side. It is recommended to bend them towards each other. This will help make the task easier and achieve better results. First, it is worth making 2 holes in the denim with an awl.

In the absence of the required skills or tools, it is recommended to contact a professional craftsman. They will be able to quickly and accurately install rivets using special equipment. If you want to install rivets with your own hands, you should first study the technique of the procedure and determine the type of fittings. This will help you achieve good results.

What you need to install or repair buttons on clothes

Getting started, you should prepare:

awl - as an auxiliary tool for basting holes and rolling the edge;
a set of punches - to create a neat hole in the fabric;
pliers - for fastening the fastener;
hammer - to secure the structure;
anvil - for placing rivets on it.

It is best to purchase them in a professional store, since the quality of the tools must be high. Otherwise, damage to the buttons or their unreliable fastening is inevitable.

Their durability depends on the metal of the tongs.

When buying, you should pay attention to whether they bend, so that there will be no problems in the future. In the absence of a special tool, you can get by with the minimum set that can be found in any home:

pliers;
hammer;
punch or screwdriver;
metal spoke;
wooden block;
rubber.

If you need to sew on a button, you will need a needle and thread in the color of your clothes.

Button installation

Sewing production involves the installation of accessories using a specialized mechanism - a press. If the enterprise has small production volumes, then they use manual equipment - these are levers or percussion mechanisms. Large factories use devices of the electromechanical type.

Installing denim buttons manually requires the following tools:

awl - it pierces the fabric in the place where the fittings are supposed to be installed;
hammer;
pliers;
bolt (if the button has a through hole);
metal tubes to fix the floating leg.

It is important to remember that the workplace must be stable, and it is best if it has a wooden surface.

4 Installing rivets on clothing

The most difficult riveting process involves heavy, coarse fabrics that are often used in outerwear. Difficulties accompany the installation of rivets on jeans. But if you work carefully, use a good tool, follow the technological steps and do not rush, you will certainly succeed in attaching a rivet. How to put fittings on heavy fabrics correctly? Let's analyze the process in more detail.

The best rivet for jackets, coats and windbreakers is the four-part button. To install it, you will need the same tool as for installing the blocks. The leg of the four-part button is unbent from the bottom and from the top, then the standard riveting process described above is carried out. The installation process of denim accessories is somewhat different from all the others, because it requires a special denim button, most often we are talking about installing a button for jeans.

With the help of an awl, a hole is made in the right place, a button leg is located in it. A denim button is placed on a metal anvil, then a leg is driven into the button. This is the easiest and safest way to install a rivet on denim.

Now how to remove a rivet

Removing a rivet sometimes requires as much care and attention as its installation requires; attention, accuracy and patience will come in handy here, especially if the use of this rivet is planned in the future. Without special equipment, it will not work to remove the rivet at home without damaging it and the fabric that adjoins it.

If its use is not planned, it is enough to cut off its head with an anvil, a hammer and a knife.

Correctly installing and removing the rivet is a matter of certain skill and skill, but everyone can learn this, having acquired the simplest set of sewing tools and good accessories.