How to wash a hookah: TOP 5 best products and rules for cleaning at home so that there is no smell

Recommendations

Some tips will help keep all the compartments of the refrigerator clean, without the formation of dirty, difficult to wash off deposits. If stains do appear, then they begin to be removed before general washing of the device.

Freezer compartment cleaning

The freezer requires careful maintenance. After defrosting, wipe all boxes and walls with a damp cloth. A solution of ammonia is used to disinfect the surface. Dissolve ammonia in water. In the finished composition, a sponge is impregnated and the chamber is wiped.

Grease and dirt

It will be possible to wash off traces of grease and dirt with dishwashing gel:

Dissolve the cleaning agent in warm water.
The composition is applied with a sponge to dirty areas.
For the components to work, the composition is left for 4 minutes.
The dirtiest areas are wiped with a brush.
Then it remains to rinse off the product with clean water.

Mold

Mold marks often appear on rubber. To get rid of them will help solutions based on ammonia and acetic acid:

The selected component is diluted with water.
Apply the composition with a sponge to the damaged area.
It is better to clean the folds of the seal with a toothbrush.

The seals and walls of the refrigerator can be cleaned from mold with Domestos or Whiteness.

Rust

Rust stains and old deposits inside the refrigerator work well with baking soda or hydrogen peroxide formulations. If rust appears on the door, then it is better to paint over the place with a suitable paint.

Yellowness

The outside of the refrigerator and the white removable parts will begin to turn yellow over time. Treat yellowness with products such as bleach or stain remover. From folk recipes, compositions based on vinegar, soda, hydrogen peroxide are effective. The selected component is applied to a sponge and all surfaces of the device are wiped.

Stickers and glue marks

Sticky marks from stickers or scotch tape can be easily cleaned with vinegar, alcohol or vegetable oil:

the selected agent is applied to a cotton pad;
impregnate the adhesive surface with the composition;
it takes 8 minutes for the component to act on a dirty place;
the sponge needs to be soaped and wiped over the problem area;
then it remains to rinse the area with clean water and wipe dry.

How to clean a hookah flask

Maintaining cleanliness is not at all difficult, even a beginner in smoking can handle it. Remember - it is not enough just to rinse the hookah flask. Over time, cloudy mucus forms in it - the same plaque. It smells bad, and it looks so-so. To remove it from the flask, you have to try.

Basic rules for keeping the device clean:

before you start washing and cleaning, let the narghil cool down after smoking;
it is better not to use chemical agents for washing the flask, since it is rather difficult to remove them completely. Traces remaining on the walls will impair the taste of the smoke and may cause an allergic reaction in the smoker;
you can use a cloth, sponge or brush to remove plaque. The main thing is that all instruments are clean.

If there are already traces of mucus or plaque inside the flask, fill it with water and baking soda and let stand. Another good detergent is citric acid. Then it remains to simply remove the dirt with a brush and rinse the vessel from the inside properly.

If suddenly you don't have a brush or a good sponge at hand, pour some rice or buckwheat inside the hookah flask, you can also use charcoal. Shake the jar well to remove the dirt from the inside of the flask.

The next step is to let the device dry. Wipe the glass on the inside and outside of the flask thoroughly with a soft cloth, then lay the parts to dry.Nargile can be used again for smoking only after it has dried properly when disassembled.

As you can see, cleaning the hookah is not difficult at all. It can even be placed in the dishwasher, but then you still have to properly rinse and dry the parts - machine cleaning will not completely remove all plaque.

How to properly wash a hookah flask:

Mix equal amounts of water with soda, collect this mass on a brush, clean heavily soiled areas.
Pour about a third of the water inside. Add 1 sec. l. soda, dissolve.
Pour in a handful of any dry cereal (for example, rice).
Shake vigorously. Grains beating against the walls will clean off the plaque.

After that, you will need to pour out the soda solution and rinse the flask with running water. It is better to soak a hookah that has not been washed for a long time in hot water to soften the dirt.

Cleaning the hose without water

Method one: punishment, or whip it well. Holding both ends of the hose in your hand, confidently, but without fanaticism, hit it a couple of times on the sofa to knock the stuck debris off its walls. Blow through the hose from both ends while keeping your finger in the air stream. Blow until the debris is no longer felt by your finger. If desired, you can repeat the procedure. If you have read to here, then it is better to go and buy a new hose, because this one is no longer a tenant

Second method: from blowing to sucking Take an air compressor (for example, the one used at gas stations to inflate wheels) or a powerful vacuum cleaner and blow or suck in air through a hose, which will remove non-adherent particles. For reliability, blow the hose from both sides several times. Plus, in this way, you can dry the hose after washing it. Again, if you do this every time before a smoking session, then it's time to throw the hose in the trash and get a new one.

Hookah component care

Before you clean the hookah, it should be disassembled element by element. Often, the narghile is washed immediately after smoking. Therefore, allow the unit to cool down. And only then they start cleaning the elements.

Hose care

Hookah hose is a part that requires careful cleaning. Resinous deposits accumulate in it. Before flushing the hose, it should be understood if the accessory can deteriorate after exposure to water. This applies to a leather hose or, for example, an accessory covered with velvet. In such cases, it is best to dry clean. Dry cleaning is also recommended for older metal hoses. Under the influence of moisture, such an accessory will quickly rust. Dry cleaning involves cleaning the hose from plaque with a dry brush. After that, the hose should be blown out.

Silicone hoses are easier to clean. It is enough to hold them under running water until clear water flows out of the hose. Hold the hose underwater with the side to which the mouthpiece is attached. Then we remove the accumulated dirt on the inside of the hose with a brush. The brush should be dipped in a soda solution. Rinse the accessory after cleaning. Drying should be natural, with the hose in the unfolded position.

Flask care

Of course, it is recommended to wash the hookah after each smoking. However, there are situations when no one has washed the already cooled hookah. As a result, mucus and plaque appear in the flask. So that there is no unpleasant smell during the subsequent use of such a flask, it should be soaked in a soda solution and allowed to stand for some time.

A popular question among smoky lovers is how to clean a hookah flask without using a brush. For this, you can use rice or buckwheat groats. After the flask has stood with a soda solution, pour rice or buckwheat into it and shake the flask.

The outer side of the flask may be cleaned with special glass cleaner and rags.

Bowl Care

The hookah bowl can be easily cleaned under running water immediately after cooling.In the case when burnt tobacco is poorly cleaned, it is necessary to soak the chillim in hot water for 5 minutes. The holes in the bowl can be cleaned with toothpicks.

A brush is recommended for better cleaning.

Mine maintenance

Before you clean the hookah shaft, it should be disassembled into its constituent elements. This will make cleaning much easier and more effective. If the shaft is solid, just clean it with a stiff bristle brush and a soda solution with the addition of citric acid. The proportion of soda and acid is 4: 1. And so much water should be added so that the resulting solution looks like a gruel.

If you don't have a brush, you can use a regular rag. It should be twisted into a bundle of such thickness that it fits snugly against the walls of the shaft. We pass the resulting harness into the mine

It is important that the ends of the fabric are not hidden inside the shaft. And with progressive movements we remove the dirt from the inside

Then we rinse the element and let it dry.

Small parts care

All small parts are also cleaned only after they have cooled down. In this case, you can not use a brush. All small items can be easily washed from ash with hot water.

How to wash the bowl

Clay may darken over time, and it will not be possible to completely wash it. If it is covered with glaze, small cracks form on it from high temperatures.

Before washing the earthenware bowl from the hookah, it is recommended to put it in a container of hot water for a few minutes. This will make it easier to remove burnt tobacco from it. After soaking, the part is washed with water, if necessary, cleaning the holes with a toothpick.

Do not use soap and a wide variety of household chemicals. They always have flavors, and if you clean the hookah with them, in the future you will have to breathe all this while smoking. The best option is citric acid and baking soda solutions. Treat all the details with them, and then you will need to thoroughly wash and dry the flask, shaft and bowl in order to finally remove the hookah smell.

How to clean at home

Every hookah owner will inevitably face the problem of cleaning a smoking appliance at home. Carrying to a store or workshop for service is expensive and impractical. It is easier to master sanitation skills on your own.

Removing smoking residues

After the bowl has cooled down, the completed smoking session, the hookah must be cleaned. Pour the remaining liquid from the flask, rinse the mouthpiece (if its design allows) and hoses.

Processing the mouthpiece with water

Let's make a reservation right away: wooden mouthpieces cannot be washed. Only metal or glass. All others can be cleaned with a rag, fishing line or toothpick. Or replace it with new ones.

How to wash the insides with water

The hookah, divided into parts, is washed in warm water, without the use of detergents (the smoker will then breathe them). It is permissible to use a brush, a clean kitchen sponge, or a rag with a line. If there is no threat of damage to the coatings, add soda (citric acid). Wash until completely clean.

Cleaning the hose

Hoses are divided into washable and non-washable. The first includes silicone, reusable. The second - metal. They are simply thrown away over time. Silicone hoses are washed by connecting to a water tap, under the pressure of warm water.

Wash my cup correctly

Usually, the bowl is washed simply by hand, but if this fails, then it is soaked in warm water for 10 minutes. The holes are cleaned with a toothpick, washed under running water. Do not use detergents.

How to wash a flask

The procedure is preceded by disassembling the hookah with pouring out the remaining liquid. Then, using a brush and a pinch of soda, clean the flask. Buckwheat (rice) grains will cope with bloom - they will work like an abrasive. It is enough to pour a handful inside, pour water and shake it several times.

How to clean a mine

All mines are divided into 2 types:

collapsible;
whole.

The type of construction influences the cleaning method used.But it is imperative to wash the mine, and thoroughly and "conscientiously".

Collapsible

This option is easier. Disassemble the shaft as much as possible, including pipes and valve. A brush, "lemon" or soda are actively used. All components are cleaned, washed under running warm water. And so on until the complete elimination of contamination. At the end, the elements of the shaft are wiped dry and laid out on a clean towel.

Welded

The general cleaning principle is similar to the previous case, only the situation is aggravated by the fact that the cleaning of hard-to-reach places will have to be carried out more thoroughly. The main participants in the procedure are the same - a brush, soda or citric acid.

Drying

When, finally, everything is washed clean, the parts of the hookah are laid out to dry. They are preliminarily wiped with a clean cloth, this will speed up the process.

Hookah is assembled in reverse order. If there is no experience or there are doubts, then it is better to write down in advance what is connected where, and only then proceed to cleaning. The very design of the smoking device is simple and uncomplicated, it is difficult to get confused in it.

Step-by-step instructions for cleaning a hookah

To clean the hookah from smoking products, you need to prepare:

flask brush;
special long brushes;
hot water;
toothpicks;
soda or citric acid;
soap solution.

Mine cleaning

Hookah can be washed without a brush, but this method is not very convenient and will not be able to cope with the rest of smoking completely. To do this, you need a thin stick and a small piece of cloth. A piece of material is moistened in a soapy solution, wound on a stick, then inserted into the hole of the shaft, cleaning is carried out with back and forth movements.
After that, the shaft is washed under running hot water.
Cleaning the shaft with a brush begins with the preparation of a cleaning solution. To do this, dilute citric acid in warm water in a ratio of 4: 1, dip a brush in the resulting mixture and clean the part inside.
Then rinse under water.

The process of cleaning a non-separable shaft is a little more complicated. It is washed to remove dirt particles, then cleaned with a brush or other thin object and left under running water for several minutes. After that, all holes are blown to remove moisture residues and the part is left to dry completely.

Washing the hose

Particular attention is required to clean the hose, as a deposit from resin residues settles inside it. The tube is rinsed under running water until all the debris comes out and clean water appears

The inside of the accessory is cleaned with a thin special brush to remove plaque residues. The mouthpiece is rinsed for complete disinfection. To wash the hose, use a soda solution or detergents, which can be purchased at specialized stores. Finish cleaning by blowing and drying.

Flask cleaning

The flask is rinsed 2-3 times under running water.
Then soda is diluted with water in equal proportions, with this solution, using a brush, clean the walls of the flask from contamination.
If the old plaque remains inside after cleaning, the part is soaked in a soda solution for a while, then rinsed thoroughly. To prevent plaque from accumulating, cleaning is repeated after each hookah smoking.
If you don't have a brush on hand, a natural abrasive agent: buckwheat or rice grits will help to clean the inside of the flask. It is poured inside, a third of water is poured and the device is shaken well. The groats beating against the walls of the vessel will clear the plaque.
Vinegar and water or an alcohol solution are also suitable for cleaning if the vessel stinks after a long stagnation of the liquid.

Bowl washing

The bowl is washed after it has cooled completely. If a lot of carbon remains on the surface, the part is pre-soaked in hot water for five minutes.
Then the bowl is rinsed under running hot water using a soft sponge. If tobacco particles remain in the holes, they are cleaned with toothpicks. During washing, you need to try so that there is no smell of strangers.
During prolonged use, the bowl becomes dull, this is a biological feature of clay. The glazed part retains its original appearance longer.

You can clean the hookah without a brush, but this will require some skill and will not completely remove plaque and microbes. You will need a flap of thin elastic fabric and a knitting needle or Chinese food chopstick. You need to wrap a rag on a knitting needle, wet and soap it. Gently pushing it into the throat of the shaft, clean it with a reciprocating motion. After removing the spoke, rinse the shaft with running water.

Hookah shaft cleaning

Mine cleaning requires special attention and basic knowledge. To clean it, we need a special brush, which can be bought in hookah shops - its cost will be about 100 rubles. Rinse the hookah shaft under a pressure of water in such a way that the water flow is directed opposite the path of the smoke path. In other words, lean the lower end of the shaft against the crane.

Then use a brush to remove any remaining dirt. It must be of the right size so that the villi are in close contact with the shaft tube. For better cleaning, you should use a small amount of soda, pouring it into the mine, or on the brush. As soon as the dirt stops coming out, flush the shaft under high pressure of water for 2-3 minutes.

In addition, the valve openings and tubes should be flushed, as sometimes contamination appears there as well. Remember to flush these holes with water to avoid contamination. Remember that many modern hookahs have a collapsible shaft, which makes cleaning the hookah quicker and easier.

Can a hookah be washed without a brush?

Nothing is impossible for skilled hands! During "hot" shifts, hookah men do not have time to clean their wards for 20 minutes, so they wash them in a completely different way between smokes. Full cleaning begins after the shift.

First aid in the fight against pollution is rinsing under a good warm pressure and drying.

The liquid in our pipes is not crystal clear by itself, so this method is more likely to get rid of smoked tobacco odors than germs.

Sometimes soda or citric acid is used for cleansing. In theory, these substances cleanse scale (in electric kettles and washing machines), but in fact, in order for this to happen, the appliance needs to be boiled. It is hardly possible to make the narghile "vyvarka". Also, fine powder particles can damage the coated ones, especially on inexpensive devices. Thus, the dignity's condition will only get worse.

It is necessary to check with the manufacturer or seller whether it is possible to wash the hookah using soda, lemon or other detergents.

How to clean a mine: 2 ways

Myths have been dispelled, we move on to the most interesting: how to replace the ruff.

You need

regular clean cloth of a small size. It is better if it is dense, not stretching;
long thin device. Since the times of the USSR, kitchens have such thin metal sticks that pierce cabbage - they are ideal. You can also use knitting needles or sushi sticks. The latter will not be convenient, but they are more familiar to us than anything else.
stationery gum.

Option 1:

Roll up the fabric with a tube, thread it inside the shaft, push it with a stick. The ends of the rag should remain on both sides of the shaft. Wipe with progressive movements from the inside.

Option 2:

Wrap the fabric around the stick. Make sure that the resulting volume fits snugly into the hookah pipe. Secure with a clerical rubber band. You will receive an analogue of the brush. If the stick is not too long, clean at both ends.

The semblance of a device can be made from fishing line and rags. True, you will only find such attributes if, along with smoking, you are fond of fishing.

We wash the flask

It is much more difficult with her without a special device. Ideally, the hookah maker has two brushes: one for the flask and one for the pipe.The first has a ring with bristles, which allows you to clean the bottom with high quality.

The neck of the product is very thin, so it cannot be washed with a cloth. Better not even try - there is a risk that it will be very difficult to pull it back out.

There are several ways to rid the container of plaque and odors:

pour out the contents, add rice there, shake and let stand for a while. Rice absorbs moisture well and removes plaque, although for all the magic to happen, the walls of the container must be left moist.
pour dissolved citric acid or soda inside. Top up with hot water (not boiling water!) To the brim and leave to cool.
if you have a large bucket, basin or any container where the flask will fit completely, you can fill this container with hot water, dissolve a lemon in it and immerse the accessory for half an hour.

Important: all parts must be thoroughly dried before the next session!

Small parts

Basically, the bowl, hose and saucer are not cleaned with ruffs, but we will tell you the basic rules for cleaning them.

all accessories must cool completely before starting water treatments.

do not wash these parts with chemicals, powders

Maximum - solutions from lemon.
remember: hot water washes away almost everything, but it is important that it is not boiling water .. The hose is placed under pressure

Good head will handle dirt. The accessory will still absorb odors, to a greater or lesser extent.

The hose is placed under pressure. Good head will handle dirt. The accessory will still absorb odors to a greater or lesser extent.

Pay special attention to the mouthpiece - it should also be cleaned well for disinfection. The clay bowl will darken over time, you can't get rid of this either.

The glaze retains its original appearance longer, however, small cracks may appear. She is washed with a kitchen sponge under a warm tap.

The earthenware bowl will darken over time, you cannot get rid of this either. The glaze retains its original appearance longer, although small cracks may appear. It is washed with a kitchen sponge under a warm tap.

Advice:

Do not use chemical detergents, even those designed for dishwashing. They have a strong aroma that can remain in the shish. The soapy consistency is difficult to wash off, so the next time you smoke in the flask, there may be residues of the product, which is extremely harmful.

Do not wash the shisha and its parts with boiling water or too cold water, this can damage the integrity of the devices.

(12 assessments, the average: 4.58 of 5)

Mine cleaning

To clean the mine with a brush, first prepare a cleaning solution: mix 1 part citric acid with 4 parts heated water. They collect this composition with a brush and treat all contaminated surfaces. Rinse thoroughly.

How to clean a hookah: taking care of all parts of the appliance

So, we have already understood that it is not enough just to buy a hookah and high-quality smoking mixtures in order to get a great idea for spending your leisure time in your piggy bank. You need to know how to take care of the device. Its main parts are a bowl, a flask, a shaft and a hose (one or more)

Let's figure out how to wash a hookah, paying attention to all its details.

Bowl. Wait for it to cool, then remove the foil. Then use a sponge to remove any remaining tobacco from the bowl. If they do not lag so easily, soak the part in hot water for 5 minutes, then grab the sponge again.
Flask. Here, a brush and running water will help you.Can a hookah be washed using household chemicals? In no case! Even after a long rinse, particles of cleaning agents will remain on the parts, which means that the obtrusive taste of soap when smoking is guaranteed to you. And this is not to mention the harm to health. So we stock up on regular baking soda and thoroughly clean the flask with a brush.
Hoses

Pay attention to what they are made of. If made of plastic, then washing is allowed

If the hoses are metallized, then cleaning should only be dry, as contact with water will cause the development of rust. So, in the first case, we pass a stream of water with a good pressure through the hose for 10-20 minutes. In the second, we blow it with air or clean it with a brush. A fishing line with a piece of sponge or cloth attached to its end is also suitable.
Mine. Here again grab the brush and thoroughly clean the channels. If there is no brush, you can run more hot water through the mine. Don't scald your hands!

After such simple manipulations, your smoking device will become as good as new. Hopefully, now it is clear to you how to clean a hookah. Carry out this procedure at least every 5-6 smoking sessions, and even better - after each use.

After cleaning, be sure to wait until all parts are completely dry. It is impossible to collect them wet into a single structure! Anyway, experts recommend storing the hookah disassembled. Place some dense material inside the flask, for example, the same "pimpled" film. Wrap the flask with it on the outside. Wrap the shaft in a soft cloth. Place the hose in the box so that it does not bend or kink. Place a lid on the box to prevent dust from settling on the parts.

Follow these recommendations for the care of your hookah, and it will give you unique sensations many more times!

Frequent use of a hookah sooner or later always leads to its pollution. Therefore, you should remember about timely cleaning of the hookah, so as not to render it unusable very quickly.

It is important to know how to properly wash a hookah at home so as not to spoil its constituent parts. Without proper care, your device will not last long - it is important to monitor and take care of it

Let's figure out how to do it!

Many people do not know that hookah care is a very important process that affects the quality of the hookah. Hookah can deteriorate very quickly and, soon, become unusable. In addition, if you do not wash the device often enough, then very soon the unpleasant taste of the past tobacco will appear. This is a very unpleasant moment and such a hookah discourages the desire to smoke completely, because the mixed smells can be a very bouquet of tastes.

First of all, it should be noted that you should not use special detergents for washing. Alas, they can leave behind unpleasant odors that will be very difficult to wash out. However, this does not apply to the whole hookah, but specifically to the hookah shaft. As a rule, the bulb does not absorb odors, but the tube should be treated carefully.

How to wash a hookah so that no smell remains

The hookah shaft is cleaned by analogy with cleaning rubber hoses:

Take a hookah shaft
Rinse it with either water or baking soda
Walk with a brush or fishing line with a rag (that is, one, securing a rag in the middle of the line, push the line from the top of the shaft to the bottom
Rinse the clean part
Dry thoroughly

When removing old unpleasant odors, many hookah lovers make a gross mistake. They try to kill the smell of the past tobacco with the "noble aromas" of chemicals. Let me remind you that this, as a rule, leads to poisoning and damage to the hookah. Then the question is: How to clean a hookah in order to exclude extraneous aromas?

In my opinion, the most effective way to eliminate unwanted odors is to clean the hookah with citric acid. Pour the "lemon" solution immediately after the treatment with soda concentrate.The tool deals a double blow: it kills odors and destroys harmful bacteria.

The way how to wash the hookah shaft

Washing the hose

Situation 1: You taste other tobacco flavors. This is called "inhabited by ghost tastes" and requires the immediate casting out of demons.

Situation 2: after a while, the hose takes on a typical hookah flavor. The process is gradual and not always noticeable for the hookah owner.

Well, now let's get down to treatment. No, priests will not be needed - we will cope on our own.

1. Cover one end of the hose with your thumb and fill it halfway or less with water. To freshen up and really clean the hose, squeeze some lemon juice into it. The dude in the picture didn't put his finger on the hose, and voila - a puddle on the floor. So be careful.

2. Close the other end of the hose with your thumb and lift it higher than the first. Take turns lifting and lowering both ends of the hose so that the water and lemon juice will flow back and forth.

3. After a couple of minutes, flush the water into the sink. Turn away, otherwise you will be horrified by the sight of the soot that you just breathed. If you want, repeat the procedure several times until clear water flows out of the hose.

4. Take the hose in the middle and rotate it by hand like the blades of a mill, dry it. The centrifugal force will suck out most of the moisture from the hose, thereby reducing the effect of the latter on the hose if it is not washable.
If you have ever seen dust, dirt or rusty flakes emerge from your hose, then know that this is due to the destruction of the hose - a completely natural process over time. And here are some ways to clean it without water.

Recommended sequence of actions and process features

So, in addition to running water, soda and citric acid, we need a thin brush or strong fishing line with a soft, lint-free cloth. If you follow all the recommendations correctly, then the desired result can be achieved without much hassle in a quarter of an hour. To clean the hookah, you must perform the following manipulations:

Remove the foil from the hookah bowl, remove all the remains of the tobacco mixture. It is best to use a soft brush or cloth for this.
We disassemble the structure into its component parts to the maximum, pour out all the liquid from it.
Next, we again assemble the device, attach its mouthpiece to the water tap and let the liquid in. We make sure that the water flows in the direction opposite to the direction of the smoke when smoking a hookah.
Then we replace the mouthpiece with the upper part of the shaft and continue the process, but now in the opposite direction. The stage using clean running water should last at least 8-10 minutes. Remember that, if possible, the liquid should be as hot as possible (if the material of the elements allows it).

Mine cleaning

Next, we disassemble the hookah again, now you need to clean all its parts separately.
First, we deal with the hose, for which we need a very thin brush with soft bristles and a long handle. Using a regular brush can damage the rubber. The use of wire can also harm the material in case of careless movements. It is best to use a profile fixture or a wire securely wrapped in rags. We move the device back and forth for a couple of minutes, if necessary, changing the fabric or washing the brush fibers. You need to blow or rinse the hose several times to completely get rid of dirt and plaque.

Cleaning the hose

Next, we proceed to processing the bowl using a clean cloth and household chemicals. First, we prepare a solution of weak concentration, pour it into a bowl, leave it for a couple of minutes, drain and clean a cloth soaked in the same composition. If necessary, repeat this several times or increase the concentration of active substances. Next, be sure to rinse everything with clean water.

Flask cleaning

After the cleaning procedure is completed, you must use a clean, soft and dry cloth to remove excess moisture from all accessible surfaces of the hookah parts. If this is not done, then they will gradually oxidize and become unusable.

The final stage is the drying of the elements. It is best to leave the structure disassembled in a place with good air flow so that all parts dry naturally. It is strictly forbidden to use artificial heat sources, hair dryers, fans, especially on rubber elements. On average, drying a hookah takes at least 18-24 hours. All this time, they should not be used, it is better to wait until it is completely dry. Immediately after cleaning, the device also does not start, because water droplets can affect the quality of the steam and even cause burns to the laryngeal mucosa.

Today, specialty stores offer specialized hookah cleaners. From a practical point of view, they are very convenient, they thoroughly wash away dirt, and do not leave behind an unnecessary aromatic sillage. True, they cost a lot, they are consumed quite actively, their shelf life expires a few weeks after the first use. Therefore, if the hookah is not used so often, it is better to limit the use of the usual household chemicals.

Stage 4 bowl and flask

If you have misused your time and haven't paid attention to your device for a long time, you will have to try. To begin with, leave the bowl in boiling water for about half an hour so that dried tobacco, tar and traces of charcoal will lag behind

After that, using a sponge and soda solution, you need to clean the bowl well and leave it under the tap for 15-20 minutes, like other parts.

But with a flask you will have to try. To begin with, it also needs to be treated with boiling water and only after that proceed with mechanical cleaning. How to wash the flask if you can't get to some places even with a brush? There is one way using regular hard cereals like buckwheat, peas and rice. Pour about half a flask of porridge and fill it with water, shake it. The grains will rub against the walls and remove dirt.