How to wash window glass: products, cleaning instructions

Proper care of the plastic frame and glass unit

With proper care, a plastic window can last for 40 years. To do this, it is enough to carry out several simple procedures 1-2 times a year.

Double-glazed window maintenance

The glass must be washed at least once a year. This procedure is not recommended in winter. This is explained by the fact that the glass may crack upon contact with warm water.

Window sill and slope care

It is recommended to wash window sills and slopes using the means recommended by the seller. This is due to the fact that these parts are made from different types of plastic. If the window sill is used as a place for growing plants, then the surface should be covered with a film. Otherwise, over time, irreducible yellow spots will appear on the plastic. In addition, every few years it is necessary to change the sealant that fills the cavities between the slopes and the window frame.

How to care for rubber seals

It is recommended to wash the rubber seals along with the glass and the window frame, wiping the latter dry after each procedure. Then these products need to be treated with silicone grease.

Plastic windows are washed using the same products that are recommended for cleaning any glass. However, when cleaning PVC products, it is prohibited to use acetone, gasoline and other aggressive substances.

Glass cleaners

During construction work, cement can get on the plastic windows. After the dirt has dried, it is difficult to clean the surface of them.

In such a situation, it is important to know how you can wash the cement from plastic windows so as not to damage them. It is possible to do, but it is necessary to act carefully and in accordance with the rules

Glass surfaces are difficult to clean. The difficulty lies in choosing a product that will not only wash away, but also will not leave streaks and scratches on the surface. So, let's take a look at the list of products for cleaning car windows, frosted shower walls, windows and more.

You need to take a container, dissolve half a piece of soap there, pour hot water over everything. For rapid dilution, stir the solution until

foam formation. There should be about 3-5 liters of water, but if there are a lot of windows, then you can dilute a larger volume at once or periodically change the soapy water. It is better to take laundry soap.

This option is not only simple but also economical.

Dishwashing detergents

Dishwashing detergents are also good for glass, especially those in the kitchen. This can be an oven or stove door, as well as a table, kettle, microwave. Here the stains are already more complex than on the windows: they are not easy from dust, but also from stains from food, fat, drinks and waste products. Therefore, dishwashing detergents are excellent for their ability to remove grease.

Add a couple of drops of detergent to a container with water and stir until a light foam appears. Next, use a rag, sponge or spray bottle to wet the surface. Shower walls can be cleaned, even matt ones.

In the department household chemicals buy product specially for glass. But they are not always universal, since what fits in a car may not always fit in a microwave or glass kettle. Besides, it is more expensive in terms of money.

Mix 1 liter of water and 1 tablespoon of vinegar. All this is stirred. You can add 1 more scoop if desired. Vinegar is sometimes replaced with alcohol, or glycerin can be added or an aspirin tablet dissolved. Vinegar has a low concentration and it takes a lot of effort to clean something with it. But the result will be good.

If vinegar is mixed with water to wash the glass table, you can add essential oil, then it will be easier to wash without streaks. By the way, the essential oil smells good and will provide a pleasant smell in the room. Glycerin is added to repel dust and dirt particles from the table. After cleaning, it is better to wipe the surface dry so that dust and dirt do not settle out of the air and onto the wet surface. Also, if moisture is removed immediately, streaks will not form later.

Potassium permanganate is one of the oldest folk remedies. It cleanses really well, but, alas, is powerless against grease stains. Potassium permanganate is added to the water in a small amount - a few drops will be enough. It is also convenient for her to clean the walls of the shower. You can add a few drops of lemon juice to potassium permanganate - it will create an atmosphere of freshness, as it cleans the air.

It is forbidden to add citric acid instead of lemon - it is difficult to dissolve and grains can leave scratches.

Chalk mixture and bleach solution

Apply the mixture to the contaminated areas using a spray bottle. You cannot use rags and sponges for this, you need to moisten abundantly. Then leave for a while and let dry. Remove dried residues with a soft cloth or paper napkin.

Removing paint

Any paint that gets on the profile or glass is removed with a cloth soaked in solvent. Removal of dried paint depends on its composition.

Oil paint

Residues of oil paint from the frame are removed with a special solvent. "Solvent" and "White Spirit" copes with fresh traces.

Cleaning process for stubborn dirt

Dried marks are carefully scraped off with a blade.
Attempts to clean windows and frames with acidic or alkaline substances are prohibited due to possible surface damage.
Abrasives and sharp tools will be harmful to the outside of the frame.

Water based paint

• Fresh traces are washed off with clean water or soap solution.
• Dried drops are removed with a spatula.
• Dried water-based or acrylic paint is wiped off with soap and a brush.

How to remove foil from a window

A glass ceramic hob scraper is best for removing foil.

You can remove the foil from the glass with a scraper to clean the glass-ceramic plate. This tool copes with the problem without the use of household chemicals.

If the scraper fails to remove everything, then the hard side of the sponge continues to clean the window using this mixture: soda or Comet powder is mixed with alcohol or solvent. It will take some time to wipe off the foil from the glass using this method. When, after painstaking work, the result is achieved, the glass surface must be put in order by polishing it with felt and diamond paste.

Another option is Amway's Gel Oven Cleaner. It is distributed over the entire surface to be treated and left for half an hour. Dilute a small amount of vinegar in water. A cloth or sponge is moistened with this liquid and the glass is washed. If the first time it was not possible to wash the film from the sun from the plastic windows, then the procedure is repeated.

A drill with a soft nozzle for grinding glass together with powder for the same procedure helps to get rid of the problem.

How to clean windows from cement

The main problem of cleaning windows from cement is the delicacy of the glass surface. You cannot use hard brushes or scrapers to remove stains. This greatly complicates the procedure, since old dirt practically eats into the glass.

First of all, try folk remedies that do not require special expenses. If they do not help, use chemical sparing agents specially formulated to dissolve and remove cement as helpers. For mechanical action, if necessary, use plastic or rubber scrapers, non-rigid brushes.

What should not be done when trying to clean windows?

To truly clean the glass and not render it unusable, avoid:

• the use of aggressive detergents;
• the use of metal brushes and scrapers;
• contact of any, even gentle chemicals on the rubber parts of the windows, as they can deteriorate.

Before buying a product, carefully study the composition

It is important that the substance does not harm either glass or plastic.

Special products and solvents

If you decide to use a store-bought product for cleaning, pay attention to the most popular ones. The principle of their action is based on the violation of the chemical bonds of the cement with the surface and with each other.

Subsequently, the solution becomes loose and can be easily removed with a wet cloth.

Comet

Bathroom cream gel perfectly softens cement.

Using a rag, apply the substance to the stains and wait for the mixture to soften. Then rinse off the dirt with a damp cloth or running water. In the last step, wipe the surface with glass cleaner and pat dry with a towel.

Atlas Szop

The tool works on the basis of caustic alkali in a composition that dissolves building mixtures.

To remove dirt, generously moisten the stains with the product and wait for the cement to soften. Wipe off the dirt with a rag, then polish the surface with glass cleaner.

Cement N Concrete Remover

The product is specially designed for the removal of cement mixtures.

To clean windows effortlessly, apply the cleaner to the dirt and wait at least 30 minutes. After you see that the stains have become loose, the cement can be washed off with water.

To remove stubborn stains, repeat the procedure until you are satisfied with the result.

Bio decap

The substance is developed on the basis of organic compounds. It is absolutely harmless to humans and takes good care of sensitive surfaces.

Apply the product first and wait for the cement to soften. Then rinse off the remaining dirt with water and polish the surface.

Blitz

The acidic cleaner, which is used to clean toilets and sinks, is excellent at removing cement stains.

Perform the procedure with gloves. Moisten the cement stains with the substance and wait for it to soften. Then wipe off the residue with a sponge and polish the glass with a soft cloth.

We wash the windows with vinegar and soda

If you have vinegar and baking soda at home, you shouldn't run to the store for a cleaner. First, try scrubbing the cement off your windows with a homemade product. To avoid burns, protect your hands with rubber gloves. For the procedure, you will need acetic acid (70%), soda, two rags, a sponge, and water.

Procedure:

• Moisten one cloth with acetic acid.
• Wipe off any dirt on the glass.
• Lightly moisten the second rag with water and sprinkle with baking soda.
• Rub the stains well for 1-2 minutes.
• Rinse off any remaining mixture with water.
• Polish the window with detergent or vinegar diluted in water in a ratio of 1:50.

We wash windows with lemon juice

If there are few cement marks and they are quite fresh, try removing them with lemon juice. For this:

• Cut the lemon in half.
• Wipe the dirt thoroughly with one half.
• Wait for the solution to soften.
• Wash off the remaining mixture with a wet rag and polish the glass.

If the cement is completely fresh, it can be easily washed off with plain water. Older marks can also be removed with water. In addition to water, you will need a rubber or plastic spatula for the procedure. Moisten the dirt and wait for the mixture to soften slightly. Then scrape off the residue with a spatula and polish the glass.

Detergents for cleaning frames and glasses

You can wash the window after all the remnants of building materials have been removed. You can use soap or regular dish detergent to clean the frame. The first should be grated and dissolved in 3 liters of water. Detergent is supposed to be only 1 tbsp. l. You can also use other household chemicals: Mr.Proper, Cillit Bang, Sanita, Domestos. For stubborn construction dust, ammonia helps. It is necessary to dissolve 25 ml of the substance in 1 liter of warm water.

To wash the glass, you can use the following means: Mister Muscle, Help, Wedge, Sif, Ecover, Second for glass. The solution can also be prepared from available tools. For example, you can mix 50 ml of alcohol and table vinegar, then add 1 tbsp. l. starch. Dissolve all this in 0.5 l of water. Funds must be sprayed from a spray bottle onto the windows, and then rubbed with a rag. The fabric should be lint-free.

First you need to wash the outside, and then the inside. It is better to carry out the procedure in the morning or in the evening so that direct sunlight does not fall on the windows after using chemicals.

Removing cement from various surfaces

For cleaning marble products, travertine, granite, most painted objects, do not use strong acids. It is necessary to use an acid-free product (approximately 500 ml per 2.5 liters of water). Moisten the surface of the stone with a solution

You can wipe off dirt with a brush, but very carefully.

Cleaning the concrete mixer

Removing concrete residues from the mixer can be done quickly and safely. There are special tools for this. Follow the manufacturer's instructions when using them. They will also help to clean the cast-iron cauldron.

Cleaning the walls of a concrete mixer used to prepare a cement mortar will be accelerated by the use of crushed stone (small stone) poured inside.

The outside of the concrete mixer can be cleaned with water and suitable cleaning agents and tools.

Removing cement from clothing

There are several ways to remove cement from clothing.

It is best to remove the contamination while it is fresh:

Scrape off the cement layer.
Remove any remaining residue with a suitable solvent.

In both cases, be careful not to damage your clothing. Pre-test the tissue's reaction to the chemical in an inconspicuous area.
Cover the stain with a piece of paper or cloth and clean with solvent.
Wash your clothes.

How to wash off a cement mortar after it dries:

1. An old, dry stain on pants or other clothing needs to be softened first. Vinegar is best suited for this purpose.
2. Cover the dirt with paper, apply the vinegar so that it does not run.
3. Clean the remaining stain with solvent.
4. Traces left after softening can be easily removed by washing.

Shoe cleaning:

Apply vinegar to your shoes to soften the concrete.
If the stain is large on the boots, carefully remove it with a knife.
Clean off dirt with a cloth or a soapy brush.
Dry your shoes, apply shoe polish if necessary.

Removing cement from the machine

You can try washing the cement off your car by dampening it with vinegar, which softens mineral-based materials without damaging the paint on your car. Apply it several times, rinse off after a while.

Expert opinion
Natalia Osadchaya

It is better to use cement thinner to clean the car body.

But when using it, it is important to be careful with metal parts (acid damage is possible).

Cleaning the floor

Vacuum or sweep the floor before mopping.

First, remove the remaining mortar mechanically using a spatula. Treat cleaned areas with a suitable solvent and rinse with water.

Removing cement from tiles

You can remove cement from tiles as follows:

1. Remove residual mortar with a spatula.
2. Rinse with water. If residues do not respond, use solvents.
3. Pour vinegar directly onto the surface.
4. Leave it to work (you can periodically remove particles of mortar from the tile with a brush).
5. Rinse.
6. Repeat the procedure until you can completely remove the cement from the tile.

Cleaning the toilet and bathtub

The best product that can clean your bathtub and toilet without damaging the ceramic or chrome faucet is vinegar. Treat it with concrete dirt, leave for 30 minutes

Then carefully remove with a scraper (ideally plastic or wooden, which will not damage the surface)

You can also clean the bathtub and toilet with special solvents. The most suitable for the bathroom is Barracuda, which is also recommended for cleaning natural stone from cement (eg granite parts), plastic products, glass surfaces.

Removing cement from metal

Using a scraper can damage the metal surface. Therefore, it is recommended to wet the hardened cement with water. After soaking, you can wash the iron with a solution of water and car shampoo in a double concentration. Do not use acidic cleaners to clean metal.

Dissolving cement in the sewer

Drain the drain, pour in the vinegar. Leave for 3 days, then try cleaning with a pipe cleaner. Reapply vinegar if necessary.

How to clean a window sill after renovation

All of the above recommendations work well if you need to remove stains that have formed during the cooking process in the kitchen. But what if the problem is more serious than ordinary household pollution?

Renovation work leaves many stains on the windowsill.

For example, if you need to clean a plastic window sill after renovation work. Proceed as follows:

Remove all the plugs, as a lot of various dust usually accumulates under them.

First, thoroughly vacuum the window structure, then wipe the surfaces with a damp sponge, paying particular attention to the caps.

If there is primer, putty or plaster on the windowsill, remove the residue with abrasive products. You can use a special detergent from a hardware store or use a mixture of baking soda and vinegar - both methods will work well if it hasn't been long.

But after a few days, only professional solvents will help you, which are not cheap - take this into account. Apply the product of your choice for half an hour, then remove with a rubber spatula or just a wooden spatula. Rinse off the remains thoroughly with warm water.

If there is foam on the windowsill, use a stiff brush to easily remove dirt. Remains of construction dirt can be easily washed off with a solution of laundry soap.

Cleaning immediately after installation

Do not think that immediately after the arrival of specialists and the dismantling of old window structures, your new plastic products will look like new. Upon completion of the installation, a film remains on the surface of the profile, and on the glass there are various stains from adhesive tape, polyurethane foam and other materials that were used in the process. Do not postpone spring cleaning for weekends or free time. The glue, with the help of which the protective film is kept on the windows, can turn yellow and dry under the influence of direct sunlight, and it will be extremely problematic to remove such dirt after a week. In addition, during this time, dust from the street will stick to it. And if the glass can be cleaned with any alcohol-containing spray, then the profiles in this matter are more demanding and capricious.

How to clean the adhesive tape from the plastic window?

The solution to this question lies on the surface. Scotch traces, that is, its remnants, of course, must be removed. Then glue spots will remain on the surface of the glass or profile, which can be easily removed with a thin blade or a clerical knife. Do not rush to use thicker tools such as a putty knife. They can scratch the surface.

The same goes for all kinds of glass stickers. If they have a paper base, but you can't gently tear them off with your fingers, take a spray bottle and spray the sticker with water.After a few minutes, the paper base will creep, and the glue can be easily removed as described above.

You will have to sweat with labels like scotch tape. Sometimes such "applications" stick to the plastic so much that it is almost impossible to remove them. Take the thinnest and sharpest kitchen knife in your hands and pick up the corners of the sticker. Gently lower the knife, with each movement of which the sticker will slowly peel off. Remains of glue can be removed with any glass chemical.

How to wash polyurethane foam?

This building material is very difficult to wipe off, so it is better to prevent such contamination than to destroy. During the work of the masters, make sure that they wipe polyurethane foam with plastic windows whenever it hits the surface of the frame. If it is not possible to keep track of the formation of stains, the dried foam will have to be scraped off with a knife.

A list of cleaning agents that help you quickly deal with such contamination:

• Phenozol. This name comes from the brand, a global manufacturer of plastic window care products. There is a product in the product line that does not contain various solvents that have a detrimental effect on the white color of the frames.
• Penosil is a European company specializing in the production of polyurethane foam and special construction adhesives. They released Premium Foam Cleaner to clean these products from work surfaces. This cleaner can even remove stains from human skin and clothing. The composition contains a small amount of solvent, but due to the presence of softening components, the agent does not harm the surface of the window profile.
• Dimexide. This drug is sold in pharmacies and is used for muscle pain or joint problems. The dimethyl sulfoxide in the gel or solution helps to clean the foam from the frame or glass. After applying the composition, the window can be washed with a soft cloth without the use of chemicals.

The drug can cause allergies, so work should be done with rubber gloves.

How to wash the paint?

This problem of all the above is considered the most difficult to solve. Usually, such contaminants are well washed with acetone, which in our case is categorically contraindicated.

First, try scraping off the stains with a razor blade. If it doesn't work with a knife, scrub the problem areas with acetone-free nail polish remover.

Water-based paint can be removed with a construction or regular household hair dryer. Hold the working device near the stain for a few minutes, the paint will soften and can be easily removed with a damp cloth.

Removing glue contamination

As mentioned earlier, if the protective film is not removed from the glass and the window sill of the plastic window in time, the glue will begin to dry out. To remove such stubborn dirt, prepare a solution with 10 parts water and 1 part acetic acid. Apply a cloth soaked in this liquid to the area where glue residues are concentrated and start rubbing the surface with a dish sponge. The better the sponge, the faster you will see results. On average, the duration of the procedure is 30-40 minutes.

Safe tools and tools

Use only soft cloths and tools, as the glass is very easy to damage

It is necessary to take care of frosted glass of doors, furniture sets, sinks using devices that are safe for covering.

Suitable for the surface:

• Synthetic suede rags. It has a multi-layer porous structure that allows it to absorb moisture well. Another plus is the absence of villi in the composition, so they do not remain on the matte surface.
• Microfiber cloths. They are comfortable, smooth and streak-free.
• Magnetic sponges. It is a device with a sponge and a scraper located on each side of it. They have a built-in magnet. Using the magnetic sponge, you can press the soft sponge well against the glass and ensure streak-free and free of dirt.
• Melamine sponge. They effectively clean dirty matt surfaces even without the use of a cleaning agent. The melamine sponge can also handle old greasy stains.

The steam mop is a tool that safely removes carbon and grease from matte surfaces, even if the stains are old. The attachments are made of microfiber, so you don't have to worry about the condition of the coating.

Safe household chemicals: how to choose

“Mister Muscle” effectively cleans glass surfaces

You can clean contaminated frosted glass on the door at home using household chemicals

When choosing them, you need to pay attention to the composition

To remove stains, do not use detergents that contain alkali, acids and silicone. Organic solvents and powders are also banned. All these substances erase the matte finish.

It is not recommended to use regular soap: it leaves a lot of streaks that are difficult to get rid of.

To wash off water deposits on glass, traces of stickers and grease, you can use the following chemicals:

• Glass liquids: Mister Muscle, Fratty Cleaner, Clin.
• Dishwashing gels: Fairy, Gala, Pril, Cinderella.
• Universal cleaning agents for various surfaces. For frosted glass such compositions as "Amway L.O.C.", "Profoam 3000" are safe.
• "Ajax" is a special tool for adding to a steam cleaner. It will help clean the glass, even if the dirt is old.

Folk remedies: their advantages and disadvantages

You can clean surfaces with a matte finish using folk methods. Their main advantages are the availability and safety of the composition. Although improvised means are inferior to industrial ones in efficiency, they still give results.

Popular ways:

• Laundry soap shavings. Grate half of the bar on a coarse grater and add a little soapy water to get a rich soapy solution. Moisten a soft sponge and wash the dirty surfaces. The composition copes with fresh greasy stains, therefore it is suitable for maintaining a matte oven door.
• Liquid soap with glycerin. Combine several tablespoons of liquid soap with a teaspoon of glycerin. Apply the composition on the surface, wait 10 minutes, then rub gently. The product is suitable for combating old grease stains.
• A vinegar solution. Combine half a glass of vinegar at a concentration of 9% with a liter of water. Put the container on the stove and warm it up under a closed lid to 50 degrees. Moisten a cloth or sponge in the solution, wipe the surfaces, then rinse with clean water and wipe the glass dry.
• A solution with citric acid. It is effective in removing limescale that often appears on shower doors. To prepare 20 g of acid, dissolve in 200 ml of warm water, stir. Pour the solution into a spray bottle, spray on the surface and leave for 15 minutes. Then wipe the door with a soft sponge, rinse with warm water.
• Composition with starch. Such a tool will cope with small dirt. Dip a spoonful with 18 g of potato starch into a liter of water, stir thoroughly. Wipe off glass elements, rinse with cold water, wipe dry.
• Composition with hydrogen peroxide and ammonia. The components must be connected in equal proportions. Dip a sponge in the resulting composition and treat the contaminated areas. This product is suitable for cleaning fireplace glass.
• Paste for removing rusty deposits from frosted glass. Mix in equal proportions finely ground edible salt and lemon juice (in a tablespoon), apply to the area of ​​contamination without rubbing. Leave for 10 minutes, then remove and remove residues with cool water. This product will also help to remove soot and burn-on from the fireplace glass.

When working with substances that are aggressive to the skin, such as vinegar and ammonia, you need to protect your hands with rubber gloves.

How to remove cured concrete with home remedies

Of course, it is very convenient to use special solvents to get rid of dried cement mortar. But very often there is no opportunity to purchase the products in question, and then you can resort to home cleaning products.

Manual / mechanical method

Dried cement mortar can also be removed mechanically: with a chisel, hammer, trowel, sandpaper. These tools can be used to clean, for example, tiles in case of intended reuse. To obtain the expected result, it is necessary to fix the tile vertically (it is elementary to clamp it in a vice) and by placing a chisel at an angle to the place of contamination, it is possible to deliver medium-intensity blows. Thus, large fragments of dried concrete will be removed, and the final cleaning must be carried out with sandpaper.

Note:
if you want to get rid of dried concrete faster and easier, experts recommend soaking the tiles in water beforehand - in this case, you can remove the cement mortar with a spatula.

Very often, for cleaning surfaces, amateurs use a grinder or a drill with a special "petal" emery nozzle - this is permissible, but only on large areas of the surface to be cleaned and from durable contaminated material.

Chemical method

At home, you can use sulfuric acid - it is diluted with water in a ratio of 1:10, heated in a cast-iron bowl. Items that need to be cleaned of cement are lowered into diluted and heated sulfuric acid - they will become clean quickly enough.

Important:
the method of getting rid of concrete with the help of sulfuric acid is dangerous for humans, therefore, both experts and doctors do not recommend using it.

Much easier and safer to perform the described procedure will help an alkaline solution from old car batteries. With the help of a rag soaked in the solution, they wipe the dried concrete and after 15-20 minutes it will be possible to remove the remnants of the cement mortar. Hydrochloric acid also works.

Remember that you need to work with such corrosive liquids only with heavy rubber gloves, a respirator and goggles.

Removing concrete from carpets and textiles

It is clear that it is not necessary to remove dried cement mortar from textiles with vinegar or grinder / sandpaper - the result will be a spoiled thing. But the following methods can be applied
:

Solvents for cement mortar show excellent results - many have long ceased to worry about "hopelessly" damaged surfaces

It is only important to choose a product that will not spoil the contaminated product.

After the completion of a long renovation, it is so pleasant to be in a perfectly clean apartment. But even such a joyful moment can be ruined, for example, if stains or cement residues remain on the surface of the tile, which can ruin such beauty. However, do not worry too much, because today there is a special modern means for removing the remains of cement mortar. It will be possible to remove, wash, clean up the remains of cement not only easily, but also quickly enough if you use the advice given in this article.

After completing the laying of the tiles and grouting the joints, the appearance of the room and the tiles fades slightly, stains and cement residues remain on the surface of the tiles. However, don't worry, a special modern tool will easily remove cement residues.

Laundering from clothes

The resin absorbs quickly into clothing, making it difficult to wash off. But small damaged areas can be cleaned out with the following products.

Alcohols

Take a 10% solution of ammonia or rubbing alcohol and wet the stain. Then leave to react for 5 minutes and carefully remove with a spatula.

Turpentine

You can effectively clean your clothes with turpentine. To do this, take in equal proportions:

• potato starch;
• ammonia;
• turpentine.

Apply the mixture to the contaminated area, leave to dry completely. Then rub with a brush and send the item to the washing machine.

Melting

The stain can be removed by heating. To do this, a blank sheet of paper is applied to the stain and ironed with a hot iron. After that, it is gently scraped off with a sharp object.

Store stain removers

Stubborn stains can be removed with professional stain removers. Oxygenated bleaches are suitable for white clothing.

Clothes should be soaked in water with bleach and left for 1-1.5 hours. Then you need to wash the item in the washing machine.

Solvents

Solvents are used to remove stains. To do this, soak the stain with a cotton swab soaked in a dissolving liquid. It takes 15-20 minutes for exposure. Then it is wiped off with a napkin and sent to the wash with conditioner.

It is recommended to dissolve stains in this way on plain clothes.

Carbonated drinks

You can easily wash away stains with drinks such as Coca-Cola, Fanta. To do this, soak the stain with a drink and leave for several hours. The clothes are then washed in the usual way.

Dimexide

You can remove the stain well with a drug. To do this, he is divorced with water in a ratio of one to three. The solution is applied to the stains for 30 minutes and then washed off.