Memo for children "safety precautions"

Safety rules for preparing the workplace

Before allowing an employee to perform duties, an authorized person must inspect the workplace. It must be in proper form, all production items must be in cabinets, cells, boxes. If there is no verifier, then it is recommended to carry out the verification yourself. And:

• any device or tool must be in good working order, without breakages, chips, cracks;
• it is recommended to prepare a nearby rag for sanitary procedures at the time of work (it must be clean);
• prepare protective equipment - a mask or goggles, gloves (it is better to have several pairs);
• connect electrical items to the network for their subsequent electrification;
• check the absence of voltage;
• any workplace must be in good condition (stairs, walkways, roofs, etc.).

Attention! These are the main criteria for the correct setting of the place for work.

What threatens children and pregnant women

Synthetic adhesives are the most dangerous. The reason for this is the content of phenol, gasoline, acetone, dichloroethane and many other toxic solvents in them. These include epoxy adhesives. Their use is impossible in rooms where children and pregnant women are.

Pregnant woman and baby

Epoxy adhesives differ from others in packaging - it always contains two tubes. The substances that make up the epoxy glue cause irritation of the skin, mucous membranes of the respiratory tract and the membranes of the eye, and negatively affect the liver and nervous system.

No less harmful are polyurethane-based adhesives, such as Moment glue. Due to the high popularity of this brand, counterfeits containing toluene and toxic solvents are often found on store shelves. The danger of Moment glue lies in the presence of a quick-drying solvent in the composition, which negatively affects the nervous system and mucous membranes.

Clay Moment

If you use Moment glue during pregnancy, observe safety precautions: use a filter petal, protective gloves, thoroughly ventilate the room.

Children are very fond of making a variety of crafts and one of the first they get acquainted with is a sweep of a cone for gluing. For these purposes, in most cases, a glue stick is used. It is made on the basis of PVA or PVP, glycerin and water. This composition is non-toxic and even with direct exposure to the skin, no reaction will occur. But what if the child bit off the glue stick? The composition of the glue is not dangerous if it enters the stomach

The only precaution is taking an absorbent drug such as activated charcoal and drinking plenty of water. If the child has eaten the glue stick whole, gastric lavage should be done

What the pencil consists of is not so important, it is better to pay attention to the manufacturer and the price of the product. A quality product is produced only by well-known time-tested brands

Safety instructions for working with glue for children and adults

For work, both in production and at home, you can use a number of household adhesives. Some of them require the use of fairly simple but effective health protection measures:

1. gloves made of impervious material such as latex,
2. rubber goggles,
3. gauze bandage.

To apply the mixture, it is necessary to use auxiliary tools - brushes, spatulas, dispensers, cotton swabs

It is important to ensure good ventilation in the work area.As an additional measure, the instructions may indicate the exclusion of exposure to temperatures, electricity, sparks, sunlight, open fire.

When working with safe PVA glue, there is no need to comply with special requirements, except to exclude it from getting into the eyes. If this does happen, they must be thoroughly rinsed with water.

If you have to work with hazardous epoxy mixtures, you should definitely stock up on a filter mask, protect your eyes, skin, and create good ventilation in the room.

VIDEO ON TOPIC

It is important to teach children how to work safely with scissors and glue. First of all, the child needs to be told how to properly store and use scissors.

General rules:

the scissors must be kept in a case,
on the work table, the tool should lie closed with sharp ends down,
they must be passed in rings forward,
scissors lying on the table should not protrude beyond the edge of the table,
tools with a blunt end, as well as with a loose fastener, are not suitable for use,
cannot be cut on the fly,
while working, it is important to watch the fingers of the left hand (for left-handers - right).

When working with adhesives, you must:

lay an oilcloth on the table,
use a brush to apply,
handle the glue carefully so that it does not get on hands, hair, eyes, clothes,
after finishing work, tighten the lid of the glue can tightly, rinse the brush and hands with soap and water.

Hot glue and hot glue safety precautions

Dos and Don'ts when using a glue gun

Working with a heat gun and hot glue requires caution, otherwise you can get burns to the skin, as well as damage furniture, clothes, valuables. Children are allowed to use the thermo gun only under the supervision of an adult

The manufacturer is not always able to provide proper insulation between the housing and the heater coil, therefore, if this malfunction is detected, it is better to refuse to use the gun. The use of the equipment is not allowed in damp rooms.

To ensure that the use of hot glue and a heat gun is not harmful, observe the following rules:

• prepare a place for work - lay an oilcloth, put cardboard on the table to put under the spout,
• do not leave the tool unattended when not in use, turn it off,
• the thermal gun should not lie on its side, its place on the stand,
• only a working tool is suitable for work,
• do not touch hot glue and the tip of the instrument with your hands,
• upon completion of work, the equipment is disconnected from the network.

With careful handling of the tool, difficulties should not arise, and the result of its use will certainly please.

Peeling off the material and removing the adhesive

It happens that leather or other materials were glued unevenly, incorrectly. There is a need for unsticking. It is much easier to do this if you used adhesives 888 Ultra Red, 888 Ultra Blue. It is necessary to start heating at a temperature of about +400 degrees from the edges of the material, which will bring the glue into a liquid state, after which it will be possible to separate the coating. A new layer of glue is not needed, it is enough to level the coating or eliminate inaccuracies in pasting.

If the problem occurs near the edge of the cover, it can be easier to fix. You need to wet a cotton swab in U35 cleaner, gently dissolve the glue and tear off the material. After it is warmed up and re-glued.

888 Ultra Plus does not react to heating because it contains a hardener. It can only be peeled off after a short period of time after application with U35. The unsuccessful glue is removed from the surface with this thinner-cleaner.

Safety engineering

Once you have made a conscious decision to give your child scissors, you need to immediately explain to him that scissors are not a toy. You need to use them only for their intended purpose and only at the table.The basic safety rules for using scissors are described below:

- Scissors cannot be taken without permission

- The scissors must not be placed on the edge of the table, they may fall and injure

- Scissors must not be left open

- Do not run your hands over the open blades of the scissors, they are sharp and you can get hurt

- Scissors cannot be passed with the blades forward

- Scissors must be stored in the stand with the handles facing up

- The scissors cannot be held with the blades up or towards you, you can stumble and get hurt

- Scissors cannot be cut on the go

These are the basic safety rules that you must explain to your child before starting to work with scissors. You yourself must remember that a small child should not be left alone with scissors in hand, especially if you do not have one. This luxury can only be afforded closer to school age.

I wish you good luck and creative ideas !!!

PVA glue, what does it consist of

Vinalon is the main component of PVA glue.

The base of the glue is synthetic fiber.

The main component of synthetic fiber is polyvinyl alcohol.

Since the base of the glue does not contain toxic elements, PVA glue, unlike many chemical adhesives, is not dangerous and does not threaten the health of people (unless, of course, you will eat and use it for a limited time).

During the production process, vinalone is converted to polyvinyl acetate.

Next, the polyvinyl acetate is diluted to the desired consistency and the result is PVA glue. PVA glue can be different, it depends on what it is intended for.

PVA glue can be made according to GOST, and can be made according to TU, it all depends on various components in the form of additives.

To enhance adhesion, which makes the gluing very high quality, add alcohols and various elements.

If PVA glue is required that is capable of retaining its properties in the cold, in order to impart plasticity, plasticizers can be added to the glue in the range of 1-2%.

The advantages of PVA glue include its fire safety, frost resistance, moisture resistance.

The only drawback is the long drying time of the glue, within 24 hours.

But, on the other hand, PVA glue is very economical, its consumption is from 100 g / m2.

How to behave in an emergency

An emergency can happen at any time. You need to be ready for it. This is influenced by production technology, seasonal tools (winter, summer), and other circumstances. Here it is recommended to proceed as follows:

• remove objects from the employee, the place of the accident. If possible, de-energize them to avoid fire;
• close windows, doors, if necessary. Or open them, free the exits and openings;
• report the situation to the authorized bodies or the management of an organization, institution, other employees;
• if necessary, use a fire extinguisher, first aid kit. Provide first aid to the victim;
• call an ambulance or fire department if necessary;

Rules of conduct in emergency situations

• leave the room or place where there is a risk to life;
• do not panic, do not get nervous, do not provoke other employees or passers-by;
• if possible, record emergency circumstances on a mobile phone, on a sheet of paper (act, sketch);
• if necessary, go to the medical center on your own or take the victim;
• do not continue the production process until the causes of the accident are clarified;
• use all safe methods to eliminate the causes of the accident.

These are the main actions that are recommended by experts in the elimination of emergencies, accidents, crashes.

Attention! The most common cause of industrial fires and smoke pollution is employee negligence. By observing safety rules, labor protection, dangerous situations can be avoided

For this purpose, each new worker is informed about the possibility of such situations occurring.

What else is worth knowing about safety at home

Sometimes it happens that people at home find themselves in extreme conditions. The danger can come from household appliances:

• electrical;
• gas;
• cold or hot water.

Fire safety

To avoid trouble you need:

be careful with electrical appliances;
having felt the smell of gas, you must immediately call the emergency service at 04, inform the address;
it is necessary to notify the neighbors and not to light a fire in the building.

It is difficult to foresee the possibility of non-standard situations, but knowing the basic requirements, you can navigate the security according to the circumstances.

Scissors and children

Any object in children's hands can be dangerous, first of all, for the child himself. For this reason, before giving the scissors, you need to explain to the baby how to behave when using them.

He must firmly remember the safety rules and always follow them. Despite the fact that children's scissors are not as dangerous as adults, you can harm yourself with them. Toddlers often love to play with all the materials at hand, and scissors are not an object that can be used for this purpose. There are also some requirements for adults who teach children how to use a new instrument.

At first, children should not be left unattended when working with scissors. Left alone, the guys can forget all the rules and hurt themselves: if you don't cut yourself, then pinch your skin, which is also very unpleasant. And that's not the worst part.

In addition to mastering the safety rules, you also need to teach your child how to hold the instrument correctly. The first step towards this will be special exercises that will help develop the hand-eye coordination necessary for the safe and correct use of this instrument.

There are several such exercises, and they are all effective in their own way. To develop strength in children's hands, you can use the following method: fill a simple rubber toy with water and ask the child to squeeze it out. The kid will surely like this exercise, which makes it possible to splash water with impunity.

Another option is to invite your child to make holes in the paper using a hole punch. You can take a curly hole punch that makes flowers, hearts, or something else. This will interest the child more. This exercise also contributes to the development of the required strength.

How to teach children?

It is equally important to teach your child how to hold the scissors correctly. It will also keep him safe from accidental injury and damage. Developmental exercises will prepare the child's hands for working with this tool, after which you can start practical exercises

Developmental exercises will prepare the child's hands for working with this tool, after which you can start practical exercises.

If the child took the scissors in his hand, then the thumb should be pointing up. One of the rings is put on the finger. The middle finger is threaded into the other ring, the index finger is placed over the ring. The nameless and pinky fingers should be bent.

The correct use of the tool and the observance of safety measures will make the use of scissors less dangerous. This applies equally to adults and children. After all, if children use special scissors that do not differ in sharpness, while being created taking into account the fact that they will be used by a child, then in adults the tool can be as dangerous as possible.

To learn how to teach a child to use scissors correctly, see the video below.

PVA glue, the most common types

The most common types of PVA are:

-Household or wallpaper glue. The most popular glue, it is used to glue wallpaper on wooden walls and on plaster walls, and paper is also glued with it. This glue has increased frost resistance and wide popularity;

- PVA stationery glue. This glue is always at hand for workers with papers.Since this glue is not toxic, since it does not contain a plasticizer, it is bought for children, for various crafts. Stationery glue is easily washed off with water and is not frost resistant;

-super PVA glue (PVA-M). It is considered the highest quality PVA glue, it contains many additives and a thick consistency. Suitable for gluing a huge amount of material. Glues cardboard, paper, wood, metal, porcelain, leather, plastic, fabrics, tiles and even linoleum;

- homopolymer polyvinyl acetate dispersion, the glue has the strongest adhesive ability, since it contains plasticizers. They are added to mortars, used in textile, glass and printing industries, mainly in industrial enterprises.

What glue can be dangerous - the most dangerous compounds

Not all components of the glue can be harmful

Experts identify the following components, the handling of which requires the greatest care:

• toluene: can harm the liver, nervous system,
• epoxy resins: irritating to the skin,
• hardeners: may inhibit breathing, cause a drop in pressure,
• anhydrides: dangerous for the respiratory system, mucous membranes,
• phenol formaldehydes: cause skin dermatitis.

Among household mixtures, the most dangerous glue is considered to be cyanoacrylate, presented on the shelves, for example, under the brand name "Secunda" and similar ones.

It causes a burning sensation on contact with the skin, and also affects the mucous membranes of the eyes, including due to poisonous vapors. Other synthetic adhesives can also be classified as toxic, for example, Superglue, Moment, epoxy and others.

The gasoline, dichloroethane, phenol, acetone included in their composition, at an increased concentration, actively affect the respiratory organs, mucous membranes, and human skin.

The only safe among synthetic mixtures is PVA, which is approved for use even in children's institutions. Does not burn, does not contain toxins, at the same time it adheres well to paper, wood, cardboard and other materials.

Even kids can observe safety with PVA glue, so it is suitable for making children's crafts, as well as simple repair work at home.

In the modern world, not everyone is ready to wait several days for the glue to set, and even more so, not everyone wants to spend time preparing it.

Another group - silicate adhesives, although they are considered safe, due to the sodium metasilicate included in the composition, are capable of corroding the materials to be glued, as well as "yellowing" paper, therefore they are used less and less for repair work today.

Safety instructions with scissors

Many of the points in this list are intuitive, but it's better to consider them in order:

First of all, the scissors should be stored in a dry place to avoid rust on the blades.
In no case should you cut anything on the go and on the move: any work requires a stable workplace and a highly desirable sitting position.
Sharp scissor blades must not be held upside down.
The tool should not be left open.
Place the scissors so that they do not hang over the edge of a table or other work surface.
When working, it is extremely important to watch the fingers of your free hand so as not to damage them by the movement of the blades.
You can't run with scissors.
They should be passed in rings forward, holding on to the closed blades.
It is also not recommended to cut with the edge of the blades, for this it is better to use their middle.
It is best to keep the scissors from falling to the floor. This could damage some parts and increase the risk of injury.

Specifications

The quality of the scissors depends on the hardness of the cutting insert material. They are made of carbon steel, factory sharpening is kept on it for a long time. The length of the blades can vary from 130 to 240 mm. The most popular models are 150-210 mm long. The ergonomic design of the handles can be oval, round or ellipsoidal.Models come with rings of the same size and asymmetrical handles. The latter, in combination with rubberized gaskets, tire the hand less during intensive and prolonged work.

Solid and durable all-metal scissors are made from solid metal plates connected to each other. A layer of plastic is applied to the iron rings. In combined models, only plastic is present in the handles, such a product will not last you long. In addition to stainless steel, titanium or nickel plated models are also available. The micro-notch applied to the edges of the blades prolongs their service life without additional sharpening.

General labor protection requirements

1.1. Individuals who are at least 18 years of age of relevant qualifications, who have undergone special training and knowledge testing, have 1 qualification group in electrical safety, who have passed introductory and initial instruction at the workplace, internship and who have received admission to independent work, are allowed to work independently on sheet scissors and press scissors. Repeated instruction on labor protection is carried out at least once every 3 months.

Re-examination of knowledge on labor safety and re-instruction on electrical safety is carried out at least once every 12 months.

1.2. Observe the internal labor regulations of the enterprise on the territory of the enterprise. Be attentive to moving vehicles and hoisting machines in operation.

1.3. Do not turn on or stop machines, machines and mechanisms on which you are not instructed by the administration (except in emergency cases).

1.4. Observe the work and rest regime established at the enterprise. Normal working hours cannot exceed 40 hours per week. Lunch break 30 min. The total time for rest and natural needs during the shift is 34 minutes.

1.5. When working on scissors and press-shears, dangerous and harmful production factors that act in the process of work are:

moving machines and mechanisms, moving parts of equipment, fixtures and tools that can lead to injury;

the processed material, workpieces with improper and careless handling, accidental fall can lead to injury;

insufficient illumination of the working area - can lead to visual impairment;

increased noise levels in the workplace can lead to hearing damage;

a dangerous voltage level in an electrical circuit can lead to electrical injury;

1.6. For the safe production of work, it is necessary to use personal protective equipment:

1.7. Every worker must know and follow the operating instructions.

1.8. In case of any interruption in the supply of electricity, compressed air, pressure drop in the hydraulic and pneumatic systems, it is necessary to turn off the equipment.

1.9. If an electric current is detected on the metal parts of the equipment, an abnormal operation of the electric motor (hums), a break in the ground wire, it is necessary to turn off the equipment and report the malfunctions to the master. Self-repair of faulty electrical equipment is prohibited.

1.10. Switching the scissor control system from one mode to another (from single to continuous) and from one control method to another (from manual to pedal) should be done only with the permission of the master.

1.11. Each employee must receive fire-fighting instructions, be able to use available fire extinguishing equipment. In the event of a fire or if signs of burning are detected, immediately inform the fire brigade of the plant by phone.…, Report to the foreman or another person of the shop administration and start firefighting with the available means (fire extinguisher, sand, and other firefighting equipment).

1.12. Immediately notify your immediate or superior manager about any situation that threatens the life and health of people, about every accident that occurs at work, or about a deterioration in your health. Provide first aid to victims of injury or sudden illness.

1.13. If you find any deficiencies in the workplace or malfunctions of equipment, lifting machines, tools, devices, inform the foreman or work supervisor. It is forbidden to eliminate any malfunctions on your own, if such work is not included in the scope of your duties.

1.14. Observe the rules of personal hygiene, wash hands with soap and water before eating, do not eat at the workplace, but use a special room for this purpose, Wear clean, clean, non-oiled clothing and shoes at work.

1.15. Every worker is obliged to know well and unswervingly follow all the requirements set forth in this manual.

1.16. Persons who violate this instruction are liable in accordance with the legislation of the Russian Federation.

Presentation on the topic: "Safety rules when working with a needle, pins and scissors." - Transcript:

1

Safety rules for working with a needle, pins and scissors

2

Guess! I am small, Thin and sharp. I am looking for a way with my nose, I drag my tail behind me. A needle with a thread An iron bug, A worm on the tail A pin A small bucket Sits on a finger, Hundreds of eyes Looks in all directions. Thimble

3

A story about a needle What came first - a needle or a clothes? This question will probably surprise many: is it possible to sew clothes without a needle? It turns out you can. Primitive man sewed animal skins, piercing them with the bones of animals or fish. This is how the ancient awl looked. When the ears were drilled with fragments of flint (a very hard stone) in the awls, needles were obtained. About 600 years ago, Arab merchants brought the first steel needles to Europe. Threads were threaded into them with the ends bent into rings. By the way, where is the eyelet of the needle? It depends on which one. The usual one - from the blunt end, the machine room - from the sharp end. However, some new sewing machines do just fine without needles or threads - they glue the fabric together. But people cannot do without a needle. The needle is a real helper, and therefore they glorify it in poetry and songs, they do not forget it in proverbs, sayings and riddles.

4

Needle Handling Guidelines Store the needle in the needle bar. Do not leave the needle in the work area without thread. Pass the needle in the needle bar with the thread. Do not put the needle in your mouth. Do not stick the needle into clothing. Use a thimble when working with a needle. Check the number of needles before and after use. Always store the needle bar and needle in one place. Stick the needle into the needle bar while sewing. Do not get distracted while working with the needle.

5

Guess! Scissors! Experienced tool - Not big, not small. He has a lot of worries: He both cuts and cuts.

6

The Scissor Story That's right, scissors. Now every child will guess this riddle. But there was a time when even adults, not just riddles, did not know the scissors themselves. Because they weren't invented. When it was required to cut something, they took a knife. But about three and a half thousand years ago, someone connected the handles of two knives with a springy bridge. We got the first scissors - for shearing sheep. And to this day they are called sheep. And more than a thousand years ago, another person came up with the idea of ​​replacing the bridge with a carnation. And a wonderful instrument was born, about which a riddle is laid. Any tool consisting of two movable halves held together at one point is a lever tool.And the first feature of this tool is that when you apply a relatively small force to its handles, a very significant force arises on the working part. The lever tool allows a person to easily nibble on wire, cut metal sheets, loosen tight nuts, bend nails, and even cut a dress or build a paper house. Scissors are used everywhere: in a locksmith's shop, and in a surgical office, and in a garage, and in a depot, and on a spaceship, and in a garment factory, and, of course, at school in labor lessons. Currently, there is a wide variety of scissors: household, garden, tailor, manicure, medical, sheep and many others, without which a person cannot do.

7

Rules for working with scissors Use well-adjusted and sharpened scissors. Scissors should have blunt, rounded ends. Place the scissors in rings towards you. Watch the movement of the blades while cutting. Do not leave the scissors open. Pass the scissors rings forward. Do not wave your scissors, do not bring it to your face. Use scissors as directed. After finishing work, put the scissors in the case. Always store your scissors in a specific place.

8

How nice it is to do something with your own hands! Everywhere there are miracles in life, you just find them always. Just be more attentive, Do not forget to see the miracle. I'll tell you a secret, kids, Scissors, needles, threads, They do such miracles, That we are always glad to them.

Choosing scissors for a child

The choice of scissors for the baby must be approached with all responsibility. Safety and convenience should be the main criteria. Small and almost toy scissors with animal handles for learning to cut will not work.

Many people advise to buy children's scissors at the pharmacy for the first acquaintance with scissors, designed for cutting nails in babies. I do not recommend doing this. Why? And try to cut something yourself with such scissors and the question will disappear by itself.

If we have already decided that our child has grown up to use scissors, then they should be the most real ones. Choose medium-sized, blunt-ended scissors on the blades from your local supply store. It is good if the handles of the scissors are rubber - they are softer and do not slip.

And, of course, the rings at the handles of the scissors should fit the size of the baby. It is better if one ring is round (for the thumb), but the other is elongated (for the index and middle fingers). So it will be easier for the child, otherwise the fingers will scatter in all directions.

It is also desirable that the scissors are sold with a cover.

Paper handling rules

1. All fold lines are made clearly, ironing well. To avoid dirty spots on the paper, iron the fold with closed scissors or put a sheet of paper in place of the intended fold and iron it on top. Moreover, if the fold is single, then it is convenient to arrange the sheet so that the fold is on the right or on top.
2. If you need to tear the paper into strips, you need to consider in which direction the fibers are located in it. If you tear along the fibers, the tear will be long and fairly even. And if across, then a long strip will not work. To get a feel for this, practice on newsprint.
3. If it is necessary to glue a part on a flat sheet, glue the part to be glued. If you smear the contour of the part on the base sheet, and then attach the part itself, it will not be even and smooth, wrinkles and folds will appear on it.
4. The part to be glued must be firmly pressed. To do this, use a clean sheet of white paper and a piece of flannel. The part is smeared with glue, placed on a base sheet, lightly pressed in the center, straightened and put on clean paper. After that, with a flannel cloth, carefully iron the part from the center to the edges.

General safety requirements when working with hand tools

Russian legislation provides for safety requirements for different types of tools. It:

• manual;
• mechanized;
• electric (electrified);
• pneumatic;
• firefighter, etc.

Briefing

Requirements are a special measure, the line between permission and duty. The general character is here because they are not assigned to a specific object or a group of similar objects. This includes preparation of the workplace, compliance with sanitary and hygienic standards. Here are a few of them:

• wear goggles, gloves if necessary;
• it is recommended to inspect each item before completing tasks;
• repair work products on time, fix breakdowns;
• timely inspect inventory;
• it is forbidden to work with a faulty tool (it needs to be corrected - to eliminate deficiencies).

This also includes performing work in hard-to-reach places. Height is of particular importance. In such situations, personal safety should come first.

Important! It is recommended to be careful and careful. There is no need to rush, try to complete the assigned tasks faster - personal safety depends on it

General requirements

Safety requirements during work

When starting production tasks, you should rely on the following:

• the time of the year is of great importance when carrying out work. Do not stay in the sun, frost, cold or icy water for a long time. Uniforms, overalls must be appropriate;
• do not overload the network, monitor the voltage;
• do not hold several objects in your hands at the same time;

Memo

• lighting must comply with norms and standards. Here it is recommended to be guided by the current legislation;
• do not continue to work in the event of pain or other physical disorders;
• smoking is allowed only in designated areas. This could result in a sudden fire;
• when repairing equipment, it should be disconnected from the network or all mechanisms and its elements should be stopped.

Attention! These are important points for any kind of hand tool activity.

Safety rules with a needle, pins and scissors

In everyday life and at work, people have to use stabbing and cutting tools, which can easily and simply injure themselves. To avoid injury, you need to carefully, diligently adhere to the established safety rules. In classes with students, adolescents, work with sharp and piercing objects becomes a special concern of adults.

Household scissors

Safety with a needle

The rules for storing and using a needle are as follows:

• the place for storing piercing objects (needles and pins) should be a special pillow and a box;
• the needle is wrapped with thread and stored stuck in a pillow or needle bed;
• getting down to business, a certain number of needles, pins are taken. After completing the lesson, you need to make sure they are available;
• during work, piercing specimens must be injected into a prepared needle bed or fixed in a pillow;
• a special box should be prepared for broken needles;
• it is not recommended to use a rusty needle. The reasons are simple: it does not penetrate the fabric, rust stains remain on the working product, there is a possibility of breakage;
• direct the pointed ends of the pins away from you. When securing the pattern with the material with pins, you need to remember this, so as not to accidentally stumble on the tip of the needle when moving;
• start fitting by checking if there are any sharp objects in the product.

Sewing tools

It is prohibited:

• taking sharp objects in your mouth;
• fasten them to clothes, to curtains, stick them into sofas, armchairs, walls, forget them in a work item.

In conclusion

The scissors safety guidelines are a set of points everyone should know, regardless of age or employment.It is already difficult to imagine our world without the conveniences at hand that allow you to quickly and easily carry out the simplest operations. But what makes life easier is not always safe. By taking a few minutes to review certain knowledge, it is not difficult to significantly reduce the likelihood of cuts and injuries.

You just need to follow simple rules and treat dangerous tools with all available attention, because not only the result of any creative activity, but also the health of a working person may depend on it.