Features of the honda motor pump

Model WT20-X

Using the Honda WT20-X motor pump, you can pump up to 700 liters of contaminated water per minute. To make this possible, the manufacturer equipped the device with a 4.8 liter motor. with. The largest size of the permeable particles is 2.6 cm. The pump draws in water from a depth of up to 8 m, it can create a pressure of up to 26 m. The capacity of the gasoline tank is 3 liters.

With a size of 62x46x46.5 cm, the device weighs almost 47 kg. The designers made sure that it was possible to clean the hull without additional tools. Thanks to a wide range of additional components, you can significantly increase the operating time. Another positive aspect is the maximum use of wear-resistant materials. The capacity of the fuel tank allows you to pump out dirty water for 3 hours without interruption.

This device can be used:

• when to put out a fire;
• for pumping out heavily clogged liquid;
• to extract water from a pond, river and even a swamp;
• when draining flooded basements, ditches, pits and pits.

Features of motor pumps "Honda"

Irrigating seedlings, watering fruit trees, draining sewer pits, filling reservoirs with water and much more is an overwhelming task for an ordinary household pump. But a motor pump, the functionality and performance of which is many times higher than conventional electrical counterparts, allows you to do this in a few minutes.

Motor pumps from this manufacturer are distinguished by:

• efficiency - optimized fuel consumption;
• autonomy - can be installed in hard-to-reach places where there is no power grid;
• ergonomic design - the equipment can be carried over distances;
• stability of working parameters and functions, which remain unchanged through the years of service;
• safety - there is no threat of electric shock;
• environmental friendliness - low noise, minimal harm to atmospheric air;
• durability - wear-resistant materials and working units were selected;
• high warranty obligations to consumers - long-term warranty, professional service;
• maintainability - a variety of original spare parts from the manufacturer of motor pumps for replacing each working body: motor (for example, GX-120 and GX-160), primer, muffler, gas tank, etc.;
• high price - several times higher than its competitors.

The main and significant disadvantage of the Honda motor pump is their inability to distill chemically active solutions, which narrows the scope of their use.

Why buy Honda motor pumps?

Wherever power is not available, Honda pumps get the job done quickly, economically and reliably.

Reliable, powerful, versatile

Thanks to a 4-stroke engine with an electronic ignition system, Honda motor pumps are highly reliable and excellent in performance. Watering a garden, pumping water out of a pool, draining a flooded pit or extinguishing a fire are just a few of their applications.

Unique protection

All Honda pumps are equipped with an oil out-of-oil protection system - to protect the engine, high quality ceramic gaskets, fittings for the suction and discharge unit, a strainer that allows particles of acceptable size only.

Economical and maintenance-free

In Honda water pumps, the engine and pump share a common shaft. Thus, no drive belts and chains are needed. These machines are easy to maintain and clean.

Large selection: from 140 to 1640 liters per minute

All Honda pumps are self-priming suction pumps.They work on the principle of a centrifugal pump and can deliver, depending on the model, from 140 to 1700 liters per minute (8.4 - 102 m3 / h).

Serial equipment

• Oil out-of-oil protection system - to protect the engine
• High quality ceramic gaskets
• Suction and Discharge Fittings
• Strainer that only allows particles of acceptable size to pass through

Outstanding Features:

• Construction. Honda motor pumps are equipped with a 4-stroke engine, which ensures environmental friendliness, reliability of use for the entire service life.

• Ease of use. The Honda water pump is simple and convenient to use, requires no special equipment or training, and in most cases requires little effort to maintain and clean the pump.

• Security. All pumps, without exception, are equipped with special protection: in the absence of oil, the engine turns off, which prevents damage. With the help of special mesh nets, the transmission of particles of only a certain size is achieved, which cannot damage the structure of the device.

Honda motor pumps are the right choice for any purpose

Honda water pumps are a guarantor of quality, which is confirmed by certificates of conformity to Russian standards. The Honda motor pump is ready for use immediately after purchase; its operation does not require special knowledge and skills. The Honda water pump, first and foremost, allows you to achieve ease of operation, as it does not need direct access to electricity. The Honda motor pump is powered by a 4-stroke gasoline engine running on AI-92 gasoline. Honda's sophisticated product line allows you to customize your Honda water pump to your specific needs, so you don't have to overpay for unnecessary features. A small Honda motor pump with a throughput of 130-240 liters per minute is ideal for watering a lawn, a vegetable garden and green spaces, as well as pumping water from reservoirs for their own needs.

For industrial purposes, Honda water pumps are used to pump out dirty water, crushed stone, pebbles. As protection against large particles, cleaning pumps are used, which ensure stable operation regardless of the amount of impurities in the water. The only negative: cleaning such a Honda motor pump is more laborious due to its specifics.

When there is a need to raise the pumped-out water to a greater height, a more powerful Honda motor pump is used. Honda water pumps of this type are quite efficient: from 1300 to 2300 liters per minute.

Nuances of use

Honda motor pumps are used wherever an economical, safe and environmentally friendly device is needed. According to the manufacturer, it is possible to move any model of the pumping unit without any problems. Even after many years of use, the basic operating parameters remain stable. Engineers were able to select the most wear-resistant materials and parts.

All models are equipped with high-performance four-stroke engines. Tests have confirmed that these engines emit even fewer gas and dust particles than specified in quality standards. There are devices that prevent accelerated wear of working parts when the engine oil supply is depleted. Fill oil only into the cooled engine. But it is advisable to drain it immediately after stopping, then it will turn out better.

For the highest tightness of the motor pump shaft, oil seals are used. In trade catalogs and in information documents of service centers, they can also be called mechanical seals. In any case, these parts are subdivided into mechanical and ceramic segments. They should snuggle as tightly as possible to each other.

It is important to take into account that Honda motor pumps (regardless of the specific model) are not suitable for pumping or pumping out chemically active liquids. Do not use clean water seals on pumping installations intended for pumping dirty water (and vice versa)

Among the parts necessary to restore the performance of Honda motor pumps are invariably present:

• manual starters;
• fully assembled gas tanks;
• bolts for fixing housings and flanges;
• vibration isolators;
• intake and exhaust valves;
• adjusting nuts;
• mufflers;
• carburetors;
• crankcases;
• ignition coils.

An overview of the Honda WB 30 motor pump, see below.

Model WB30-XT

The Honda WB30-XT motor pump is capable of pumping up to 1100 liters of water per minute or 66 cubic meters. m per hour. It creates a fluid pressure of up to 28 m. Having completely filled the tank, you can use the pump for about 2 hours. Its total weight is 27 kg, which makes it easy to move the device at your own discretion.

The system works great if you need:

• irrigate the field;
• deal with fire;
• drain the pool.

Even if the dimensions of the pool are 25x25 m, the motor pump will perfectly cope with pumping it out. It will take no more than 14 hours. The pumping unit can also be used in reservoirs, but only on condition that the particle size is no more than 0.8 cm.

The device of a motor pump "Honda"

This equipment is a conventional hydraulic pump to which an internal combustion engine is connected. This manufacturer has focused on 4-stroke motors, which have high performance, long service life and do not exceed the amount of gas and dust emissions allowed by environmental and hygienic standards.

The use of the shaft in the design made it possible to get away from the belt drive and increase the reliability of the structure. And the implementation of a special protector in case of full oil consumption does not allow the engine to wear out prematurely.

Each model of Honda motor pumps, in addition to the device itself, is completed with:

• connecting clamps;
• filtration nozzle;
• nozzles - inlet and outlet, which allow you to complete the installation of the pump without the use of tools.

Checking the unit before purchasing

Before purchasing such a device, you should pay attention to its characteristics and packaging. Also check the serial numbers on the engine and in the documents, and then you can proceed to the phased assembly of the equipment:

Make sure that there are no foreign objects in the inner cavity of the nozzles;
When assembling the unit, first of all, you need to install the supply and suction tract, after which you need to install a cleaning filter;
It is very important to ensure that the suction hose is not compressed, otherwise you will not be able to achieve the required pressure of the device during operation;
Tighten all the fasteners where the clamps are used. Since, during the operation of the equipment, a very large pressure is created, it is very important that they are securely fixed;
Then it is necessary to perform a general inspection of the unit and the reliability of the fastening of all components;
Then you can go directly to the installation of a motor pump next to the reservoir

And if, after turning on the unit, the water supply began, then it means that the assembly was performed correctly.

The main components of pumping units with an internal combustion engine:

• Fuel tank of various sizes;
• The frame on which all the components of the device are attached;
• Handle for starting the motor;
• Gas supply lever;
• Special plug for filling engine oil;
• Spark plug;
• Air filter;
• Fuel shut-off valve;
• Engine shutdown button.

Motor pump "Honda" WB20XT

A gasoline unit that passes water with mechanical contaminants (their size should not exceed 0.6 cm). The most common household tasks - filling / draining pools, tanks - he performs without unnecessary labor costs and unnecessary consumption of gasoline.

Peculiarities:

• practicality - the equipment is easy to operate, it does not need special maintenance and frequent repairs;
• primer snap-in for quick manual start;
• tool-free fastening of hoses;
• good pressure and performance characteristics;
• compactness.

Technical specifications:

• Power - 2900 W;
• Throughput - 0.6 m3 / min;
• Suction depth - 8 m;
• Gas tank - 1.9 L;
• Fuel consumption - 1 l / h;
• Weight - 21 kg.

Classification of motorized pumps "Honda"

The entire model range of this type of equipment can be combined into several series:

• WX - work with clean water. The smallest modification that is popular with summer residents;
• WB - multifunctional devices with decent technical and functional properties;
• WH - powerful pressure units: supply water over considerable distances in horizontal and vertical planes. Most often they justify their use for fire extinguishing;
• WT - the most powerful models, designed not only for clean, but also slightly polluted water.

Let's take a closer look at popular models.

Model WT40-X

The Honda WT40-X motor pump is optimized for pumping both clean and contaminated liquids. It can be used when pumping water containing grains of sand, silt deposits and even stones up to 3 cm in diameter. If the device is brought to the maximum intensive mode of operation, it pumps 1640 liters of liquid per minute. To ensure such performance, the engine will burn 2.2 liters of AI-92 gasoline every hour. To start the motor pump in operation, a manual starter is used.

The total weight of the structure reaches 78 kg. Therefore, it is designed exclusively for stationary use. The pump can suck in water from a depth of 8 m. Its outer casing is made of an aluminum-silicon alloy. The water pressure can reach 26 m.