Motoblock neva mb 23

The lineup

"Neva MB1-N MultiAGRO (GP200)"

Ideal for small areas. Equipped with an engine from a Japanese manufacturer, which has established itself for its reliability and durability. The manufacturer transferred the gear change to the steering column. Reducer from "MultiAgro" is the development of the manufacturer.

The technique can work with additional equipment, there are gears for moving forward, there are three of them, it is possible to take it back. Thus, the operator has the opportunity to carry out any agricultural work. Such a technique is distinguished by its high power and minimal costs. The user can adjust the height of the handlebars to suit their height.

When working on milling cutters, it is allowed to install a support wheel, due to which the best balance is ensured. The wheel is not supplied, so it must be purchased separately. The engine demonstrates a power of 5.8 horsepower, you can refuel AI-92 and 95. The width of the track created, depending on the attachment used, is 860-1270 mm.

"MB1-B MultiAGRO (RS950)"

This model is best used on medium density soil. This is a multifunctional technique on which the manufacturer has provided for the choice of gear. The engine is quite powerful and has a long service life. As in the previous model, a custom gearbox is installed in the design. The technique can be commended for its easy control of gear and gear changes and high efficiency. Even a person without experience can easily cope with such a technique.

The steering wheel can be quickly and easily adjusted according to the user's height, and the speed can be switched on the steering wheel. If necessary, the number of gears is increased through the flap and the belt, which needs to be reinstalled on the second groove of the pulley. The technique helps to quickly cope with all work on the ground, including digging the soil.

If you lower the additional wheel, installed as a support, and the steering wheel, then the installation of the cutter is quick and without additional effort. The technique can be used as a small means of transporting crops. This requires a cart and adapter. It is easy and simple to clean the area and clear snow with an additional brush or shovel. Engine power 6.5 liters. with., runs on the same fuel as the previous model, the width of the left track is in the same range.

Motoblock "Neva MB1-B-6, OFS"

It is used in poor lighting conditions on medium-weight ground. With a significant increase in ambient temperature, the manufacturer advises to work on the walk-behind tractor only early in the morning or in the evening. The design includes headlights, the work of which is carried out thanks to a built-in generator and an electric starter. There are three forward gears and a rear one, the power consumption is low.

The optimum speed for work is selected by repositioning the belt. The lever, which is necessary for shifting, is located on the steering wheel. It can be customized, which greatly simplifies the performance of the assigned tasks on uneven ground. The wheels are quickly and easily changed to cutters. An additional support wheel is not supplied.

If you plan to perform complex tasks, different types of equipment are attached to the walk-behind tractor. You can remove snow from the territory, transport crops. The fuel tank holds 3.8 liters of gasoline, engine power is 6 liters. with. The cultivation track is the same as for other models. One of the main advantages of the described technique is ease of maintenance.

"Neva MB1S-6.0"

Equipped with a 4-stroke engine, which is characterized by an increased service life. The number of gears is 4, for forward movement three and one reverse. One of the features of this walk-behind tractor is the center of gravity, which is lowered, so the operator does not have to apply additional force during operation. The power of the power unit is 6 horses, while the volume of the gasoline tank is 3.6 liters.

"MultiAgro MB1-B FS"

It can be operated in the dark, suitable for small areas. Its power is 6 horsepower, the working width is the same, but the depth of entry into the ground is 200 mm.

How to do it yourself?

If you have access to a huge selection of necessary spare parts, then, of course, it is easier to make gearboxes yourself.

But please note that such a spare part needs serious equipment for metal processing. If you have this, then you can choose a housing of optimal parameters, make holes for shafts on bearings and make a device no worse than at a factory.

Initially, you need to calculate the rated power without errors. Thanks to the correct results, you will be able to find out the optimal angle to find on the bevel gear. You need to calculate the number of spins in 60 seconds.

The gearbox made requires the determination of the conditions of its operation, including the load. Its performance will be top notch with the right temperature and lubrication. The next step is assembling the gearbox. The case can be taken from the factory. According to its diameter, you can identify the bearing housing for the shaft. A vernier caliper and a drill will help you with this.

The steel flange must be mounted on the front of the gearbox. Inside, we mount a flange bearing and a washer. The flange is secured with screws at the generator itself. The key and gear must be selected in advance. All units that are in contact with the transmission system are fixed to the rotary generator.

Operating rules

How durable the operation of the walk-behind tractor will be depends on the correct assembly, configuration and adjustment. It is strictly forbidden to work on wet soil with this type of equipment, as well as to cultivate fields that are on a slope or the ground in greenhouses. Before starting operation, it is necessary to run in

This process is considered a rather important procedure for further use of the walk-behind tractor. Before starting this procedure, it is necessary to adjust the valves, check the fixity of each of the bolts

After the integrity of the unit has been checked, it must be filled with oil, gasoline, grease, and coolant. After that, the car can be started, the speed can be reduced and the walk-behind tractor can be worked at first with no load.

Before plowing the land and working with the plow, it is necessary to adjust the carburetor, remove the clutch, and carry out a technical inspection of the transport. Each part of the walk-behind tractor must be wiped with diesel oil.

Before cultivating, you need to carry out the following activities:

• tighten the bolts, then - fix the protective shields;
• mount the holder and opener;
• collect the cutters, and then - carry out their installation;
• fill the tank with high-quality fuel;
• add engine oil or transmission oil.

Maintenance of the Farmer equipment is a service twice a year. If the equipment is idle for six months, before working on the walk-behind tractor, it is worth changing the oil in it and refilling the fuel.

Self-diagnosis of the unit consists in the following points:

• flushing the fuel tank;
• checking the position and fixing of the carburetor;
• change of lubricant;
• cleaning candles;
• constantly checking the amount of oil and adding it if necessary.

User manual

The manual for the Favorit walk-behind tractor allows the owner to competently assemble and configure the walk-behind tractor, in the future, after the purchase, all operation should be carried out in accordance with the manual for using the walk-behind tractor.Do not violate the recommendations for fuel materials, do not save on oils and lubricants, the useful life of the walk-behind tractor depends on their quality.

What oil and fuel to use for Favorit walk-behind tractors?

• Engine oil: SAE 10 W - 30 API SF or SG.
• Transmission oil (in the gearbox): TAD 17I, MC20.
• The volume of oil for the gearbox is at least 50 cm3, for the engine - at least 1100 cm3.

First start-up and break-in instructions

The first start is performed after the following actions:

• reactivation of the walk-behind tractor;
• assembly, installation of wheels or cutters (depending on the tasks);
• oil filling;
• refueling with diesel fuel / gasoline.

Starting the walk-behind tractor begins with starting the engine. The documents attached to the device contain information on engine operation, study it before working with the walk-behind tractor. After warming up the motor, it is allowed to switch to the operating mode.

Running-in duration - 25 hours. Only after running in is it allowed to give 100% of the load on the walk-behind tractor. Cultivation is usually done in second gear. It is regulated by setting the appropriate position of the opener.

Major malfunctions

Possible malfunctions of the Favorit walk-behind tractor and their elimination