Review of motoblocks huter. description of models, video work, reviews

How to choose?

It is important to understand that attachments are not universal and are selected individually for each cultivator. For example, a lug is considered a must-buy, since the wheels of the cultivator often skid when working with the soil.

To choose the right option correctly, you will have to proceed from the walk-behind tractor model.

Cutters

As for cutters, they are divided into two types: saber and crow's feet. Manufacturers add the first variety to the walk-behind tractor. It differs in a different number of sections, due to which the processing width changes, which can reach 135 cm. In general, such cutters are good for work and are convenient for disassembly.

This is important in the event of a breakdown, because it allows you to replace the problematic part, and not the entire structure. These cutters can be sharpened, but the disadvantage of the attachments is the fact that they work well and for a long time only with soft soil. If the soil is dense and complex, then it is more advisable to purchase "crow's feet". They are usually not included in the basic kit, but they prepare the soil for planting potatoes quite well.

Plow

When choosing a plow, it is important to consider the type of soil. For example, the option with one single share type share is good when the soil is light

If the soil is difficult, it is worth looking at a swivel-type product with two shares. It will plow the ground in exactly one direction.

As for preparing the soil for planting and hilling, you need to take the option with a V-shaped share

It is also important to consider the power of the unit. For example, single-row hillers with a fixed width are suitable for a walk-behind tractor with a capacity of 4 liters.

with. The rotary device does not need a hitch, since they are installed instead of the wheels of the walk-behind tractor.

Diggers

The potato digger is selected based on the type of root crops harvested. Considering that it can be fan-shaped and rattling, it is worth noting: the former is cheaper and less effective, since after it a little more than 10% of the crop remains in the ground. This is not scary in a small farm, since you can also collect the remaining root crops manually. The variant of the vibration type is distinguished by lower losses (no more than 2%), works by means of vibration, shaking out everything except the fruit.

Mowers and adapters

With regards to mowers, you will have to choose between rotary and segment ones. The former are easier to maintain, the latter are cleaner than their rotary counterparts. The adapter is available for steering wheel and steering wheel. The first option is equipped with a seat, a lift lever and a brake, it is cheaper, however, the working capabilities of the steering mechanism are significantly greater. It can perform the functions of a grader, mini-tractor, dump truck and arable unit.

Snow blower

It is important to decide on the type of device here. This can be a moldboard shovel, a brush mechanism, or a rotary ejector.

The first option is cheaper than all varieties, and its width can vary in the range of 80-150 cm. At the same time, for a larger size, it is worth purchasing a device with higher power.

Motor pumps

When purchasing such equipment, you need to take into account its performance. For example, the average range may be 20 or even 30 cubic meters per hour. The head that will be created during operation can be 4-5 m with a suction depth of about 10 m.

Attachment overview

In order to better carry out soil cultivation, the Huter cultivator can be equipped with additional attachments.More often, owners use such devices necessary in agriculture as:

• plow;
• hiller;
• potato digger;
• metal lugs.

Motoblocks, the engine power of which is 7.5 and 9 horsepower, have more opportunities for the use of one or another attachment. Installation of additional agricultural accessories is carried out as quickly and easily as possible. Thus, you can not only expand the functionality of the unit, but also turn it into a snowblower, a sweeping device, a pump and even a lawn mower.

On sale there are such types of attachments for the Hooter motor-cultivator, such as rotary mowers, harrows, water pumps, weighting agents, shovels, etc.

Models

Among the German units that have a model range, the following devices deserve special attention.

GMC-6.5

This walk-behind tractor can be classified as a product of the middle price segment. Notable equipment with an engine capacity of 6.5 liters. with., thanks to which the unit perfectly copes with the task of processing small areas of soil with different types of soil, including virgin soil. The equipment is characterized by good maneuverability and maneuverability, this feature is achieved due to chain transmission and reverse.

The equipment has an attractive external design; the ergonomics of the machine body also deserves special attention. Among the advantages, it is worth highlighting the presence of wings under the cutters, which exclude the worker's contact with clods of earth during the movement along the site. All control levers are located on the handle of the walk-behind tractor, which can be adjusted for height and angle of inclination. The walk-behind tractor runs on gasoline, the capacity of the fuel tank is 3.6 liters, the weight of the device is 50 kilograms.

GMC-7

This model stands out for its economy in terms of fuel consumption, despite its power and performance. The device runs on a gasoline engine with a capacity of 7 liters. with. Due to its low weight (50 kilograms), one person can transport and operate the walk-behind tractor. The handle is adjustable in height, pneumatic wheels are included with the machine, which significantly increase the maneuverability of the operating device.

GMC-9

This model of German agricultural machinery is designed to perform a large amount of work, therefore, the Huter GMC-9 is recommended to be purchased for an impressive farmland. As practice shows, the walk-behind tractor can handle plots up to two hectares. These characteristics are largely due to the engine power of the unit, which is 9 liters. with. Such a device can be easily transformed into a traction machine using attachments such as a trolley. The walk-behind tractor is capable of transporting a load weighing about half a ton. The fuel tank has a capacity of 5 liters. The mass of the walk-behind tractor is 136 kilograms.

MK-6700

Such a walk-behind tractor is an improved analogue of the previous modification of the German unit. The device is equipped with 8 cutters, thanks to which the area of ​​the site that the unit can process is significantly increased. A feature of this model is the presence of a coupling block in the rear of the body, which provides the possibility of joint operation of the walk-behind tractor with various types of attachments that increase the performance of the unit. The equipment has a capacity of 9 liters. with., with a gas tank volume of 5 liters.

Scope of use of Hooter walk-behind tractors

The field of application of the Huter brand walk-behind tractors is very diverse. The product of German design is very popular with farmers, summer residents and owners of country houses. Due to its versatility, the technique has found application in the communal sector. If there are components, the walk-behind tractor can replace several units with limited capabilities.

The versatility of the Hooter walk-behind tractor is achieved by installing the following devices on it:

1. Cutters. Farmers use these devices most often. By loosening the topsoil, the cutter blades catch and pull out the weeds along with the roots. When working in heavy soil, its processing is carried out in several stages with a capture of 6-10 cm for each pass. Processing is carried out in 2nd gear. In the absence of pushing, the unit moves by itself.
2. Plow. Depending on the power of the equipment and the density of the soil, devices with 1, 2 or 3 plowshares are used, fixed on a common frame. The plow is used for raising virgin lands, laying trenches for communications and excavating the soil when arranging pits.
3. Hiller. This device is used for plowing light soil and creating beds. Hilling allows you to give the beds the correct shape, to ensure a better supply of plant roots with moisture and oxygen. When passing through the site, hillers remove weeds, contributing to an increase in yield.
4. Hay mowers. In agriculture, rotary devices and trimmers are used. Rotary mowers have a working width of up to 120 cm and are used for making hay. Trimmers are indispensable for domesticating lawns in the yard.
5. Snow plows. Having a set of a rotary cleaner, a blade and a brush, you can clean paths, platforms, gates and gates from fresh and densely packed snow.
6. Trailers of various configurations. The most popular among diggers is the universal cart. This product has an operator seat and body. At the same time, you can use a mowing machine or potato digger for harvesting and transporting crops.

The engine pulley can be used to connect an electric generator and a water pump.

Attachment overview

Hooter cultivators perform soil tillage with milling cutters, are aggregated with some mounted implements: plow, hiller, potato digger, metal lugs. Motoblocks Huter with 7.5 hp engines and 9 hp. have great possibilities when operating with attached implements.

Motoblock (cultivator) Huter MK-6700

The mounting of the attachment to the Hooter walk-behind tractors is carried out quickly and allows not only to efficiently carry out the entire range of agricultural work, but also to convert the unit into a snowblower, sweeping machine, pump or lawn mower.

The most popular accessories are: a plow, rotary mowers, potato planters and potato diggers, harrows, cutters and openers, a water pump, lugs, various couplings, weighting agents, an adapter with a seat, a mini-trailer, a snow blower, a shovel-blade, a household brush.

Features of operation, maintenance

New units are supplied for sale unassembled, so the owner should first familiarize himself with the assembly steps and adjustments in detail in the instructions.

How to start a walk-behind tractor Hooter

• open the fuel cock
• close the air damper
• turn on the ignition
• set the gear shift lever to neutral
• turn the throttle lever to minimum
• Pull the starter handle until resistance is reached, return to the starting point and then jerk sharply.

The started engine is warmed up for 1-2 minutes, smoothly opening the damper. The number of revolutions of the engine can be adjusted with the throttle lever. The engine is stopped by turning the throttle lever to the "Slow" mark and turning off the ignition.

Maintenance of Huter walk-behind tractors consists in checking the fuel level, engine oil, making the necessary adjustments to the cutters, and the opener. After work, it is imperative to clean the unit from dirt, earth residues, dust. The fuel for cultivators and motoblocks Hooter is AI-92 gasoline. The 10W40 grade is used as engine oil.

Break-in, first start

Huter walk-behind tractors are distinguished by high-quality reliable components, so their running-in takes a short time.First, start the engine in accordance with the instructions, let it run for about 20 minutes at idle speed. Then, a blow-through is performed.

In this mode: XX / gassing work for 2 hours. Upon completion, the first oil change is carried out, then the change is carried out every 10 hours.

Motoblock Huter GMC 7.5 HP

Major malfunctions, repair

Huter cultivators and walk-behind tractors are solid equipment, according to the owners, they do not have any typical malfunctions. Malfunctions in most cases occur due to violation of the manufacturer's recommendations.

Engine malfunctions (does not start, runs intermittently) are associated with old gasoline, incorrect position of the air damper, disconnection of the high-voltage wire from the spark plug or poor contact, dirty air filter, clogged fuel system.

Do not operate with low or no oil level, this will damage the engine. To check the oil level, turn off the engine and allow the oil to escape into the crankcase for 4-5 minutes. Then remove the dipstick cover, wipe dry and insert, without twisting, back. From the mark on the dipstick, determine the actual amount of oil in the crankcase, top up if necessary.

Maintenance

Running in

The actions that are included in the running-in significantly extend the service life of the walk-behind tractor, since during this all parts are run in to each other and all units are lubricated.

Also, you have the opportunity to test a walk-behind tractor that is under warranty service.

Running-in is carried out after purchase and long-term storage. By doing the following, you will not waste much time, but will extend the life of the unit:

1. Check for the presence of oil in the engine crankcase. Fill tank full of fuel.
2. Start the engine according to the instructions and let it idle for 20 minutes.
3. After 20 minutes, run through, increasing the speed to the maximum. Try changing gears. Work in this mode for 4 hours.
4. For the next 4 hours, you can connect the wheels and ride the walk-behind tractor without using attachments.
5. After running-in, drain all used oil and refill with new one.

Features of use

For successful operation, keep an eye on the oil level in the tank. With a low level or no lubricant at all, the engine may fail.

The manufacturer recommends pouring engine oil of 10W40 type at positive temperatures. The first replacement is carried out after 10 operating hours, and the subsequent ones agree with the plan (every 50 operating hours).

Gasoline with octane number 92 is used as fuel. To fill the tank with gasoline, you must first loosen the cap and wait until the pressure in the tank equilibrates.

Important! Do not close the choke when starting a warm engine, because you can fill the spark plug

The main breakdowns and their causes

Attachment types

A wide range of attachments for Hooter walk-behind tractors, which is offered for sale, significantly expands the capabilities of the unit, thereby helping to carry out all the hard work on the farm.

Attachments

The following types of equipment are suitable for all Hooter models:

• Pump for supplying water to the site;
• Lugs that facilitate the passage of the walk-behind tractor on viscous soil;
• Nozzle for trimming the edges of the landings;
• Cutters of various sizes are suitable for cultivating the soil as well as removing weeds;
• The potato digger is designed to collect potatoes by separating the root crop from the ground;
• The harrow helps to create furrows, which are subsequently used for planting or watering;
• The hiller is an indispensable device when it is required to carry out hilling in rows.
• The adapter and trailer are used to improve working comfort as well as to transport goods.
• The mowers are designed for cutting grass and other grain crops.
• The plow is the most demanded device after milling cutters, as it plows faster and more efficiently, especially if the task is to process virgin soil.
• Snow blower, blade-shovel - can be used from other manufacturers, while coping with the work no less effectively. The snow blower throws snow several meters to the side, therefore safety measures should be taken when working with it.
• The hitch allows you to attach any attachments to the walk-behind tractor.
• Weights are used in those models of walk-behind tractors that are lightweight for effective immersion in the soil.

Description

The Huter brand belongs to the German company HüterElektrischeTechnik GmbH. Since 2011, the production facilities of the concern in the PRC have launched the production of various equipment - electric generators, welding and electrical equipment, garden tools, high pressure washers, lawn mowers, trimmers, electric saws and chainsaws, snowblowers, motor-drills.

Hooter motor-cultivators and walk-behind tractors are represented by a small model range - within 10 modifications. Despite the insufficiently ramified dealer and service network, Huter walk-behind tractors are gradually conquering the post-Soviet space.

The equipment is produced under the strict supervision of German specialists, corresponds to the best European standards, therefore, some marketing flaws are successfully covered by the impeccable quality of the machines in combination with budget prices.

Pros and cons of Hooter motoblocks

The main advantage of a foreign-made product is its adaptation to the operating conditions that are typical for our country. The engine of the walk-behind tractor can operate on low quality fuel and oil, in the rain and in dust. Users appreciated the functionality of the machine and the capacity of the fuel tank, which allows it to work for a long time without stopping for refueling. The high permeability of the unit is achieved by a wide spacing of the wheels and the possibility of replacing them with weighted ground hooks. The equipment is convenient to operate, it is easy to operate and maneuver in hard-to-reach places.

There are also disadvantages of motoblocks of Chinese assembly. Chief among them is the poorly developed network of service centers. Since domestic options are not suitable for imported equipment, they have to be ordered and wait up to two weeks. The same story is with spare parts, which are almost impossible to find on sale. But, parts and accessories delivered to order have all certificates and are of high quality.

General information, purpose and design features

The Huter cultivator allows you to effectively loosen and cultivate the soil, preparing it for further use as intended. The design of the device is designed in such a way as to completely eliminate the manual work necessary when performing agricultural work on personal plots.

The functions of the cultivator are as follows:

• loosening the soil by means of rotating double and single steel cutters;
• plowing the field, the depth of which can be adjusted using a metal opener;
• processing of soils of personal plots even in hard-to-reach places of a limited area;
• a high level of maneuverability, as a result of which a person has the opportunity to operate the device simply and without any difficulties.

The design of the Huter motor cultivator is quite simple. The source of its mechanical energy is a powerful gasoline internal combustion engine. Such a device is equipped with an electronic ignition and a manual starter. The working tools possessed by the Hooter motor cultivator are its metal steel cutters. Above them there are special shields that prevent stones and soil particles from getting into the person controlling the cultivator. The model uses a single steering wheel to improve maneuverability.

The cutters that are used in Hooter motor-cultivators, unlike the plow, do not turn over the soil layer. As a result, soil erosion does not occur.

Attachments

Each manufacturer proposes to use auxiliary components in conjunction with their products. As for the Chinese Huter walk-behind tractors, they can be operated with the following equipment.

• Cutters. The assortment of these tools is quite wide, so the part can be selected specifically for a particular task.
• Pump for water supply. A very useful device, suitable for use on large agricultural areas.
• Grousers. A necessary part that increases the speed and permeability of the equipment on heavy types of soil. In particular, the use of this part is relevant in the off-season and in winter.
• Plant edge removal attachment.
• Harrow. A tool thanks to which you can make furrows in the ground. Subsequently, they are used for sowing crops or watering plants.
• Hiller. Carries out hilling of beds without the use of manual labor.

• Mower. A tool that allows you to prepare animal feed, as well as harvest grain.
• Adapter. An auxiliary element that increases the maneuverability of the machine, and also makes it possible to use the walk-behind tractor in conjunction with a trailer.
• Plow. The most popular tool used in conjunction with walk-behind tractors. During operation and cultivation of the land, the plow demonstrates much greater efficiency in comparison with the milling cutter.
• Snow blower. This equipment may be manufactured by another manufacturer. Thanks to an additional device, the walk-behind tractor can throw snow over long distances.
• Coupling. Part responsible for attaching attachments and trailed equipment to the machine body.
• Weights. Elements required for light vehicles to provide stability and good traction.

Description

The Huter brand itself has German roots, however, almost all production workshops engaged in the production of components and assembly of motoblocks are concentrated in Asian countries. This territorial division allows to reduce the cost of devices, which significantly expands the range of consumers of agricultural units. The concern is actively engaged in the manufacture of various agricultural equipment, and the first walk-behind tractors left the assembly line less than ten years ago, therefore, such equipment appeared in domestic stores relatively recently.

According to the reviews of the owners of such devices, the units are distinguished by a high level of quality and assembly, this feature is due to the presence of a multi-stage quality control system in production, which has a positive effect on the operational life of German products. However, most of the units in the mechanism are not interchangeable, which negatively affects the maintainability of the equipment.

Device

Most models have 4 main gears - 2 forward and two reverse, however, some modifications may contain more or less operating speeds. All Huter walk-behind tractors are equipped with a steering wheel with anti-slip attachments and the ability to adjust its height. Motoblocks run on gasoline, however, there are also diesel cars. All units have a four-stroke engine and a tank capacity ranging from 3 to 6 liters. In addition, the devices are equipped with a convenient speed switch, gear reducer and various cooling systems for the motor and the main units in the mechanism.

There are modifications of devices that are supplied complete with pneumatic wheels; most often, equipment belonging to the heavy class is implemented in this way. All units emit a minimum of noise during operation, in addition, the running walk-behind tractor practically does not vibrate. The working depth of tillage varies within 30 centimeters in depth with a width of 1.5 meters, but this figure also depends on the type of cutters used.