Possibilities of Husqvarna tf-338 and 434 walk-behind tractors: sharing knowledge

Features of use

In order to prepare the cultivator for work, you must perform the following steps:

• Before starting work, it is necessary to remove from the site all objects that could damage the machine - large stones, glass, wires, etc.
• Visually inspect the machine for oil or fuel leaks. Make sure implements and deflectors are not deformed. Replace with new ones if faulty.
• If the machine is equipped with a push-button engine shut-off system, make sure the cables are intact.
• Do not use the machine without protective covers or covers designed for your safety.
• Check that all fasteners are secure.

Running-in is the key to the long-term service of the walk-behind tractor.

At this time, all parts are lubricated and rubbed against each other. It is advisable to carry out all the necessary procedures immediately after purchase, as well as after long-term storage.

By adhering to the following actions, you will significantly extend the life of the walk-behind tractor:

1. Check oil level and top up if necessary.
2. Start the cultivator at low speed and let it run for a few minutes.
3. Change gears, checking their work.
4. After 4 hours, you can use the machine at half of the specified power.
5. After 8 hours, you can start full-fledged operation, but first drain the used oil and fill in a new one.
6. To work with cultivators of the Husqvarna brand, manufacturers recommend using gasoline with an octane rating of 92. On the recommendation of the owners of motoblocks of the presented brand, any oil can be used, but it is advisable to use from well-known manufacturers such as (Echo, Huskvarna, Shtil).

Description of the Husqvarna 434 walk-behind tractor

Multicultivator 434 attracts the attention of users with its technical parameters. Chief among them are:

1. It has a Subaru gasoline engine that runs almost quietly, so the noise is not heard during starting and working in the field or in the country.
2. The valves on the motor are located on top.
3. Engine power is 5 hp. with.
4. The cultivator has a reverse gear.
5. A pneumatic clutch is installed.
6. The walk-behind tractor has a high level of performance and maneuverability in the field.
7. The transmission is of a removable type, it can be chain or pneumatic.

Model 434 has been significantly improved when compared with other modifications of this company. In particular, a pneumatic drive was supplied to the handle, which allows the operator to maneuver and correctly control the mechanism. Also located on the handle are speeds that allow you to accelerate or slow down the movement of the unit.

A tow bar has been installed that has universal dimensions and is suitable for any work on the field. The cultivator has a steering column that can be adjusted horizontally and vertically. A wheel is installed on the front of the walk-behind tractor, which makes the 434 more maneuverable and more responsive. The package includes additional attachment parts, including protective cleaners, metal and rubber wheels, edge leveler, snow plow, plow. This provided numerous positive feedback from farmers.

Compared to previous models, the 434 has a higher engine speed. The motor of the 338 walk-behind tractor is capable of making 3 thousand rpm, and the improved model 434 - 3.4 thousand rpm.

Model range of Husqvarna walk-behind tractors

The Swedish company Husqvarna has been in the agricultural machinery market for over forty years. Recently, the brand entered the list of leaders in motor cultivators.This is primarily due to the quality of the products, as well as to the latest technologies that are used to create models.

Due to the power of the units, it is possible to use various additional equipment. Attachments from the manufacturer can also be found on the market. For example, a cart for a walk-behind tractor, which is slightly inferior in size to a tractor and has a large cross-country ability.

The entire model range of equipment is divided into series, which have their own distinctive features. It is worth considering that walk-behind tractors need good service, since special systems were used when creating the structure.

In this video, we will consider the Husqvarna walk-behind tractor:

Each model is suitable for use in its area, but there are also multifunctional models. These options include the popular TF 338 unit.

TF 230

The TF 230 belongs to the 200 series, but it differs in the form of sufficient power and practicality. It is used for small areas. The model has a gasoline engine version, which stands out for its reliability. The unit has all the necessary protection, as well as an adjustable handle.

The variant has low fuel consumption, which, with a 3.6-liter tank, allows for long-term operation without refueling.

TF 324

The Husqvarna TF 324 is used in medium-sized plots. There is a powerful gasoline engine with a working volume of up to 163 cubic meters. cm.

There are two gears, one of which is reverse. It is used for maneuverability and better cross-country ability. The overall dimensions of the equipment are small, which makes storage and transportation convenient. The engine is installed from the manufacturer Briggs & Stratton.

The reduced noise level is also considered an important difference.

TF 338

Husqvarna TF 338 is one of the most successful models. The main features of the unit:

• original Husqvarna Engine, which supports 92 and 95 gasoline;
• there are many additional functions that simplify the operation process;
• there is a reverse motion for greater cross-country ability and no getting stuck off-road;
• the handle is adjustable in height, which is convenient when transporting. It can also increase productivity;
• maintenance-free gearbox of autonomous type. There is enough lubricant for the entire period of operation;
• the basic package includes several protective side elements;
• wide wheels of pneumatic type allow to increase cross-country ability;
• manual start allowing all-season use based on reliability;
• the clutch actuator is protected by a completely sealed cover.

Thanks to its good power and efficient operation, the walk-behind tractor takes leading positions in the form of mini-tractor equipment.

TF 334

The TF 334 is a professional vehicle with 6.5 hp. The weight of the unit reaches 56 kg in the absence of attachments. The accessories of the cutters go deep into the ground by 0.3 m. There is a steering column that is adjustable for the height of the operator.

All other equipment is considered standard and includes all equipment, including protective guards, which are installed to protect the driver.

It is considered one of the quietest and most maneuverable models. Very convenient to operate in a small area.

TF 335

The TF 335 has a four-stroke petrol engine with 6.1 hp. It is used on an area of ​​up to 1 hectare. The chain-type gearbox has three gears, the list of which includes one return, that is, reverse.

The set includes 6 cutters. There is also a protective cover and all additional protective shields. There is a possibility of connecting various options for agricultural equipment.

TF 545

The Husqvarna 545P is suitable for large areas and difficult terrain. There is an air filter with which the service interval is increased. With the help of a walk-behind tractor, you can perform work of any complexity. It is also possible to use any attachments, including heavy ones. The standard cutting depth is 30 cm with a width of 1.1 meters.

The model is distinguished by its quality and durability.

Video review of Husqvarna walk-behind tractors

Cultivation with a Husqvarna TF 230 walk-behind tractor

Walk-behind tractor Husqvarna TF 338 in operation

Denis:

“When I read reviews on the Husqvarna TF 338 walk-behind tractors on the forums, I met the comparison as if it worked like a beast. Now I can say that, it works like a beast. Replaces several people. Now virgin land is not scary

It is important to install the cutters correctly. I immediately bought a potato digger, a snow blower and an adapter with a seat

Grousers were not needed, the car itself is heavy, pulls normally. Gasoline consumption increases a lot when I carry heavy loads - 2.5 or even 3 liters can take ”.

Anton:

“Motoblock Huskvarna works on a plot of 37 acres. Excellent traction, cannot be compared with the old gasoline models of other companies. Good build quality and the components themselves. The price is reasonable, it starts up without problems. I have not noticed any shortcomings yet. There are some nuances: it is inconvenient to pour oil, it is difficult to find a suitable sample. I am looking for a plow for him. In general, I recommend it. "

Attachments

With the help of attachments, you can not only speed up the time of work on your site, but also carry out various types of work very easily. There are such types of equipment for Husqvarna walk-behind tractors.

• Hiller - with this device, furrows can be made in the soil, which can later be used for planting various crops or for irrigation.
• Potato Digger - Helps harvest different root crops by separating them from the ground and keeping them intact.
• Plow - you can use it to plow the soil. The use is advisable in those places where the cutters did not cope, or in the case of cultivation of unplowed lands.
• Lugs are used instead of wheels to improve traction by cutting the blades into the ground, thereby moving the device forward.
• Wheels - come complete with the device, suitable for driving on hard ground or asphalt, in the case of driving on snow, it is recommended to use tracks that are installed instead of wheels, thereby increasing the contact patch of the walk-behind tractor with the surface.
• Adapter - thanks to it, the walk-behind tractor can be transformed into a mini-tractor, where the operator can work while sitting.

• Milling cutters - used for balling the earth of almost any complexity.
• Mowers - Rotary mowers operate with three rotating blades to cut grass on sloping surfaces. There are also segmental mowers, consisting of two rows of sharp "teeth" moving in a horizontal plane, they can cut even dense plant species, but only on a flat surface.
• Snow plow attachments are a practical addition to snow removal.
• An alternative to this can be a device - a shovel blade. Due to the angled sheet of metal, it can rake snow, sand, fine gravel and other loose materials.
• Trailer - allows the walk-behind tractor to turn into a vehicle carrying loads weighing up to 500 kg.
• Weights - add weight to the implement which aids in cultivation and saves operator effort.

General information, purpose and design features

The cultivator was developed by the Swedish company Husqvarna in 2015. The basic configuration of the machine includes a minimum set of options, which is not a disadvantage at all. Indeed, in this way, the manufacturer gives the buyer the right to choose the missing equipment himself, based on his needs. Moreover, the technique supports any attachments.

The Husqvarna model TF 338 is ideal for working in the garden and in the country. The characteristics of the product are so outstanding in technical terms that the cultivator is able to satisfy even the most sophisticated gardener. Swedish technology will delight the owner for a long time with its impeccable work. The machine is perfect for plowing, hilling and cultivating large areas. There is no doubt about the reliability of the equipment, since the official warranty from the manufacturer is 2 years from the date of purchase.

The front of the cultivator is equipped with a protective bumper, which is attached to a heavy-duty welded frame. The bumper effectively protects the car from external influences - stones, ruts, hard soil and other debris

This is very important when working in extreme conditions, for example on soggy soil.

The equipment is equipped with a powerful gasoline unit, which was developed by the efforts of Husqvarna engineers. The unit has a modern, robust design and is characterized by low noise and vibration levels. It picks up speed quickly and delivers stable torque even when riding uphill.

Note that not only Swedish components are used in the motor, but also parts from other European companies with a good reputation. I must admit that this is one of the most innovative engines ever used in walk-behind tractors and other household equipment.

It has minimal emissions and is easy to start in frosty weather.

The cultivator is quite compact and lightweight, thanks to which it can be actively controlled. This allows you to quickly maneuver in confined spaces, for example, in small areas with a lot of obstacles - bushes, trees and stones.

The basic equipment of the device includes pneumatic wheels, which can be replaced with metal wheels or lugs if desired. This option significantly increases the stability of the machine when working on difficult land. In addition, the cultivator can be supplemented with a plow and a hiller, with which it is very convenient to form beds after cultivation, as well as to cultivate virgin soil.

It's interesting: Characteristics of popular models of Russian hopper motoblocks

Advantages and disadvantages

Swedish agricultural equipment, according to the reviews of the owners, stands out for a number of high performance characteristics. In addition, in comparison with the rest of the European equipment on the market, the equipment is sold at an acceptable cost. However, for the most complete picture of such units, it is worth considering all the positive and negative features of Husqvarna cultivator models.

Among the positive characteristics are the following.

The range of units is presented in a wide variety of devices of various capacities and modifications, in light of which any consumer will be able to choose equipment that will satisfy his individual needs in terms of solving agricultural problems.

• Thanks to the installation of powerful and efficient Robin-Subaru, Husqvarna or Briggs & Stratton engines on walk-behind tractors, the equipment stands out for its durability and minimal risk of damage, even during long-term operation.
• Husqvarna cultivators can be equipped with a reverse function. This feature of the lineup excludes situations when agricultural machinery gets stuck in the ground, even when working with wet soil.
• The manufacturer has taken care of the ease of use of its units, so most modern models have an ergonomic telescopic removable control handle, which can be removed if necessary. This feature is relevant for the transportation and storage of cultivators.
• All machines are manufactured with a gearbox that does not require additional maintenance.

• To protect the operator during soil cultivation tasks, many models additionally have shields on their hulls that can protect against flying clods of dirt. In addition, they will protect crops from damage by the device.
• The Husqvarna motor cultivator has small wheels on its body that allow you to transport equipment. There are also units with a carrying handle.
• The configuration of the Swedish technology involves manual start of the engine, making the device quite easy to bring into working order.
• This technique stands out for its high-quality belt clutch. This unit has a long service life and rarely fails.In addition, the mechanism is reliably hidden from the penetration of various kinds of contaminants from the outside. Due to chain reducers, the units have the ability to move not only forward, but also backward.
• In the basic configuration, motor cultivators contain several cutters, as a rule, a set consists of 2, 4 or 6 parts. In action, these elements can rotate in the direction of the machine or against it.

But the technique is not without its drawbacks.

• Since high-performance machines are distinguished by their power, they also stand out for their impressive dimensions, which significantly limits the circle of people who can operate the units.
• Chain driven devices require special conditions of use, as any solid object falling into the cutter can damage the entire chain.

Models and their technical characteristics

There is a fairly large range of agricultural machinery from Sweden on the market.

Product classification is as follows:

• Husqvarna T - machines recommended for small areas;
• Husqvarna TF - walk-behind tractors designed for work on medium-sized land plots;
• Husqvarna TR - heavy duty machines for large areas.

It is worth dwelling in detail on the most popular ones.

Husqvarna TF 230

Small and lightweight walk-behind tractor, additionally equipped with a special bumper to protect the engine. The device has a folding handle and a wheel on the body for easy transportation of the unit.

Husqvarna TF 324

Garden equipment with American engine. The motor-cultivator is distinguished by its ease of operation and minimal vibration during movement. The design of the device contains protective barriers to prevent damage to crops. The checkpoint is located on the handle, the walk-behind tractor is additionally equipped with a coulter.

Husqvarna TF 334

The device has a six milling cutters, the movement of which occurs in the course of the cultivator. The unit operates at two speeds: 1 rear and 1 forward. The device weighs 56 kilograms.

Husqvarna TR 430

The equipment is equipped with large wheels, thanks to which its cross-country ability is significantly improved. The motor-cultivator contains two pairs of cutters, the movement of which is carried out in the opposite direction. The cultivator has counterweights on the body for maximum productivity and good traction.

Husqvarna TR 530

The popularity of the machine is due to the depth and width of the soil cultivation. The device has 2 speeds: 1 reverse and 1 forward. The walk-behind tractor operates on an Asian engine and a carburetor. The volume of the fuel tank is 3.6 liters. In the basic configuration, the technique is realized with two pairs of cutters.

Husqvarna T50 RS

Light equipment, the weight of which is 53 kilograms, the walk-behind tractor includes 4 cutters, the gear change is carried out using a built-in system in the handle.

In addition to the above devices, the Swedish concern offers medium-sized machines that are also in demand on the market:

• Husqvarna TF 338 9673168 01;
• Husqvarna TF 335;
• Husqvarna TF 225;
• Husqvarna TF 325;
• Husqvarna TF 434P;
• Husqvarna TF 224;
• Husqvarna TF 545P and others.

Husqvarna 200 Series

TF 224

Motoblock Husqvarna TF 224 - looks like a big toy that can become a reliable assistant for a farmer.

HUSQVARNA TF 224

This model is the smallest of the entire range and is suitable for use in small areas.

The engine is quiet, which contributes to the comfortable work of the operator, and has a power of 4.5 hp.

The steering column folds down, making the cultivator compact for storage or for easy transport.

The design provides for the presence of protective shields that protect the plant from damage during cultivation.

Specifications

TF 230

The TF 230 cultivator is a powerful and practical cultivator that makes cultivating a small plot of land much easier.

HUSQVARNA TF 230

The reliable gasoline engine has a displacement of 196 cc.

All materials used that make up the main structure are durable and reliable.

Fuel consumption is low, so a 3.6 liter tank makes it possible to work for a long time.

The gearbox has 2 forward gears and one reverse, which provides a certain amount of maneuverability.

Specifications

TF 225

The TF 225 tiller is a lightweight and manoeuvrable unit that will help you cope with the processing of a small area.

HUSQVARNA TF 225 2017

Small weight of 46 kg and relatively compact dimensions make it easy to transport the walk-behind tractor; during storage it does not take up much space.

There are only two speeds, one forward and one back.

The working width is 60 cm, allowing you to maneuver between obstacles.

An indisputable advantage is the adjustable handle, which, together with a low-noise motor, provides a comfortable working environment.

Specifications

Description

Husqvarna motor-cultivators and walk-behind tractors from a reputable Swedish company are reliable equipment for medium-sized land plots. Depending on the soil, the size of the territory, the work required, the owners can choose the appropriate model - from the Husqvarna TF224 cultivator with a capacity of 3.1 hp. to the powerful multifunctional walk-behind tractor Husqvarna TF 545P 7 hp

The equipment is being developed in design offices in Sweden. All units and mechanisms for Husqvarna walk-behind tractors are produced at our own factories in the USA, China, France, Sweden. Husqvarna walk-behind tractors favorably stand out among similar equipment of other brands for their reliability, high-quality workmanship, efficiency, minimal maintenance costs.

User manual

The instruction manual is included in the kit for each walk-behind tractor and contains the following standards.

General norms

Before using the tool, familiarize yourself with the rules of operation and controls. When using the unit, follow the recommendations in this operating manual. The use of the unit by persons who are not familiar with these instructions, and children are strongly discouraged. It is not recommended to carry out work at a time when there are bystanders within a radius of 20 meters from the device. The operator must keep the machine under control during all work. When working with hard types of soil, remain vigilant, since the walk-behind tractor has the least stability compared to already treated soils.

Preparation for work

Examine the area where you will be working and remove any visible non-soil objects as they may be thrown away by the working tool. Before using the unit, each time it is worth inspecting the equipment for damage or tool wear. If you find worn or damaged parts, replace them. Inspect the device for fuel or oil leaks. It is not recommended to use the device without covers or protective elements. Check the tightness of the connectors.

Operation of the device

Follow the manufacturer's instructions to start the engine and keep your feet at a safe distance from the cutters. Stop the engine when the equipment is not in use. Maintain concentration when moving the machine towards you or when changing the direction of rotation. Be careful - the engine and exhaust system become very hot during operation, there is a risk of burns if touched.

In case of suspicious vibration, blockage, difficulties with engaging and disengaging the clutch, collision with a foreign object, wear and tear of the engine stop cable, it is recommended to immediately stop the engine. Wait until the engine has cooled down, disconnect the spark plug wire, inspect the unit and have a Husqvarna workshop carry out the necessary repairs. Use the device in daylight or good artificial light.

Maintenance and storage

Stop engine before cleaning, inspecting, adjusting, or servicing equipment or changing tools. Stop engine and wear strong gloves before changing attachments. To ensure safety when using the device, observe the tightness of all bolts and nuts. To reduce the risk of fire, keep plants, waste oil and other flammable materials away from the engine, muffler and fuel storage area. Allow the engine to cool down before storing the unit. When the engine is hard to start or does not start at all, one of the problems is possible:

• oxidation of contacts;
• violation of wire insulation;
• water entering the fuel or oil;
• blockage of the carburetor jets;
• low oil level;
• poor fuel quality;
• malfunctions of the ignition system (weak spark from the spark plug, contamination on the spark plugs, low compression ratio in the cylinder);
• pollution of the exhaust system with combustion products.

Daily check:

• loosening, breaking off nuts and bolts;
• the cleanliness of the air filter (if it is dirty, clean it);
• oil level;
• no oil or gasoline leaks;
• good quality fuel;
• instrument cleanliness;
• no unusual vibration or excessive noise.

Change the engine and gearbox oil once a month. Every three months - clean the air filter. Every 6 months - Clean the fuel filter, change the engine and gear oil, clean the spark plug, clean the spark plug cap. Once a year - change the air filter, check the valve clearance, replace the spark plug, clean the fuel filter, clean the combustion chamber, check the fuel circuit.

How to choose a Husqvarna walk-behind tractor, see the next video.

Attachments for the Husqvarna TF 338 walk-behind tractor

To expand the capabilities of the Huskvarna TF 338 motor cultivator, the manufacturing plant offers attachments suitable for the model:

• Metal wheels 5882671-01 - strong lugs, designed for better passability of the machine when working on clay and loamy soil types. Installed by means of hubs. Supplied in a set of 2 pieces, and have the following characteristics: weight - 12.2 kg; outer diameter - 380 mm.
• Fan-type potato digger plow 5882663-01 - used for harvesting root crops (potatoes, beets, onions). Principle of operation: a correctly installed and adjusted tool undermines the soil in the middle of the row, and the dug tubers fall on long tines; when moving the cultivator forward, the soil is shaken off, and the roots remain on the surface.
• The hiller plow 5882665-01 is a single-row device for cutting furrows for planting and hilling, which is attached using a hitch that is not included in the package. Produces a dump of soil (previously treated) with the direct course of the walk-behind tractor. It has a low weight - 4.7 kg, therefore, when aggregating, it is necessary to use weights.
• Coupling 5882660-01 is a device that is designed for rigid and reliable attachment to the cultivator of various attachments (plow, hiller, potato digger).
• Set of subsoilers 5882672-01 - used for effective loosening of hard, heavy soil. Equipment weight - 15.75 kg.

For more information on attachments, visit the Husqvarna official website.